• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.3
• /
• pp.192-199
• /
• 1999

During start up and shut down, the generator is rotating at a low speed and copper dusts cause arcing between the turns in the slot. Shorted turns occurred primarily by the movement of these copper dusts between individual windings in the generator rotor. Detection of shorted turns was performed in five gas turbine generators in two combined cycle power plants. Two types of permanent and temporary flux probes were used in this paper. These flux probes have been used to develop a methodology for detecting shorted turns in an operating generator's rotor. The flux probes sense the rotor winding slot leakage flux and produce a voltage proportional to the rate of change of the flux. This pattern of flux variation is the signature unique to each rotor winding. An appropriate waveform analysis technique canidentify the pole location, the slot number, and the number of shorted turns within each slot. Shorted turns in field winding of gas turbine generator(125.7 MVA) were detected to twelve turns on al total 190 turns.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.5
• /
• pp.434-441
• /
• 2016

This paper deals with transformer turns ratio design with the consideration of loss minimization in isolated bidirectional DC-DC converter. Generally, the rms value of current, magnitude of current at switching instance, and duty ratio of a converter vary according to the turns ratio of an isolation transformer in the converter under the same voltages and output power level. Therefore, the transformer turns ratio has an effect on the total loss in a converter. The switching and conduction losses of IGBTs and MOSFETs consisting of dual-active bridge converter are analyzed, and iron and copper losses in an isolation transformer and inductor are calculated. Total losses are calculated and measured in cases of four different transformer turns ratios through simulation and experiment with 3-kW converter, and an optimum turns ratio that provides minimum losses is found. The usefulness of the proposed transformer turns ratio design approach is verified through simulation and experimental results.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.115-117
• /
• 1999

This paper deals with characteristics of universal motor of which parameters varying by stator turns and propose stator turns that has the highest efficiency. Stator turns variation results difference in current, impedance, power, torque and speed. We try to measure these data. The experimental results show the stator turns which this motor has the highest efficiency.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.8
• /
• pp.1555-1559
• /
• 2011

Turbine generator(13.8 kV, 137.5 MW) has high bearing vibration at rotation speed. Shorted turns in generator rotor windings have strong correlation with increased field current which is thus related to increase in bearing vibration. The recurrent surge oscillograph (RSO) test is performed on the rotor winding in turbine generator to detect shorted turns. The result of the RSO test indicates that shorted turns of rotor winding are generated in two locations. The RSO test was capable of identifying the presence, number, and location of shorted turns in generator rotor windings.

• Progress in Superconductivity and Cryogenics
• /
• v.19 no.1
• /
• pp.51-55
• /
• 2017

To obtain Nuclear Magnetic Resonance (NMR) measurement of membrane protein, an NMR magnet is required to generate high intensity, homogeneity, and stability of field. A High-Temperature Superconducting (HTS) magnet is a promising alternative to a conventional Low-Temperature Superconducting (LTS) NMR magnet for high field, current density, and stability margin. Conventionally, an HTS coil has been wound by several winding techniques such as Single-Pancake (SP), Double-Pancake (DP), and layer-wound. The DP winding technique has been frequently used for a large magnet because long HTS wire is generally difficult to manufacture, and maintenance of magnet is convenient. However, magnetic field generated by the slanted turns and the splice leads to field inhomogeneity in Diameter of Spherical Volume (DSV). The field inhomogeneity degrades performance of NMR spectrometer and thus effect of the slanted turns and the splice should be analyzed. In this paper, field gradient of HTS double-pancake coils considering the slanted turns and the splice was calculated using Biot-Savart law and numerical integration. The calculation results showed that magnetic field produced by the slanted turns and the splice caused significant inhomogeneity of field.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.3
• /
• pp.663-668
• /
• 2010

In driving a car, turns such as left turns, right turns, or u-turns, make the speed of the car decrease considerably. A more straight path, therefore, is probably faster to arrive at the destination than zig-zag path with same distance. In this paper, we have newly proposed the turn heuristic to make more straight path. The path navigation algorithm with turn heuristic(called as TA* algorithm) could enhance the straightness of a path by putting the turned-edges to the turn cost. It requires higher cost to use TA* algorithm than traditional A* algorithm because the straight-edge first searching have increased the search space. We have improved the TA* algorithm into the variable TA* algorithm(called as VTA* algorithm) which adopt the turn-heuristic during the a portion of the whole path.

• Korean Journal of Applied Biomechanics
• /
• v.29 no.4
• /
• pp.219-226
• /
• 2019

Objective: The purpose of this study is to provide a better understanding of short turn mechanism by describing short turns after kinematic analysis and provide skiers and winter sports instructors with data through which they are able to analyze right postures for turns in skiing in a systematic, rational and scientific manner. Method: For this, a mean difference of kinematic variables (ski-hip angle, ski-shoulder twist angle, pole checking angle, the center of gravity (CG) displacement, trunk forward lean angle) was verified against a total of 12 skiers (skilled and unskilled, 6 persons each), regarding motions from the up-start to down-end points for short turns. Results: There was no difference in a ski-hip twist angle. The ski-shoulder twist angle was large at the up-start point while a pole-checking angle was high at the down-end point in skilled skiers. Concerning the horizontal displacement of CG, skilled skiers were positioned on the right side at the upstart point. No significant difference was observed in the trunk forward lean angle. Conclusion: According to the ski-shoulder twist angle and CG horizontal displacement results, the upper body should be kept leant toward the pole. In addition, big turns should be made via edging and angulation. During pole checking, the hand holding the pole should be thrown and released toward a vector direction of the forearm.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.10
• /
• pp.1818-1821
• /
• 2008

Several off-line diagnostic tests which include the insulation resistance(IR), polarization index(PI), low-voltage AC, and recurrent surge oscillograph(RSO) tests were performed to assess the condition of generator rotor windings. The low-voltage AC and the RSO tests were performed on the gas turbine generator rotor winding to detect shorted turns. Before intentionally applying artificial shorted faults, it was confirmed by the low voltage AC and the RSO tests that the winding was in sound condition. For simulated shorted rotor winding turns, the RSO test detected the fault in the winding. The RSO test was capable of identifying the number and pole location of the shorted turns for a number of simulated shorted coils.

• The Korean Journal of Community Living Science
• /
• v.12 no.1
• /
• pp.23-27
• /
• 2001

This study is designed to find out the physicochemical quality and the morphological features of Korean wheat flour and imported wheat flour with a view to shed light on their difference. In terms of components, Korean wheat flour and imported wheat flour are similar, but the latter turns out to be better than the former when it comes to crude protein, the ratio of water absorption and the power of maintenance. Yet Korean wheat flour turns out to be better than imported wheat flour. In terms of the chromaticity of wheat flour, the latter turns out to be higher than the former when it comes to L value, while the former turns out to be higher than the latter when it comes to a value and b value. In terms of the morphological features of wheat flour, both are in the shape of an oval with starch particles irregularly attached to gluten. And imported wheat flour is getter than Korean wheat flour in terms of the size of particles.

• KIEE International Transactions on Power Engineering
• /
• v.3A no.2
• /
• pp.70-78
• /
• 2003

This paper describes a transformer protection relay based on induced voltages. The ratio of the induced voltages of the primary and secondary windings is equal to the turns ratio during normal operating conditions such as magnetic inrush, overexcitation, and steady state, but it differs from the turns ratio in the case of internal faults. For a single-phase and a three-phase Y-Y transformer, the induced voltages are estimated and the ratios are compared with the turns ratio. For three-phase Y-Δ transformers, the differences between the induced voltages are estimated to use the line currents because delta-winding currents are practically unavailable. The proposed relay is tested under various conditions such as magnetic inrush, internal winding faults, overexcitation, and different core characteristics. The results evidently indicate that the relay successfully discriminates internal faults from magnetic inrush and overexcitation. This paper concludes by implementing the relay into a TMS320C6701 digital signal processor and reports satisfactory results. The relay requires no hysteresis data and can reduce the operating time of a relay.