• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.3
• /
• pp.138-144
• /
• 2013

New experimental devices and methods to measure shaft forces of ships are proposed in this paper. The strain gauge type six-component load cell was newly designed and installed to the end of the propeller shaft. The signals generated from the sensor in the propeller rotating are transferred to the new data amplifying and processing board on the shaft and the data is transmitted to the self-made wireless receiver. To find out the characteristics of shaft forces during port and starboard turning motions in sea trial, oblique and combined yaw maneuvering tests at straight, transient, maximum yaw rate, steady conditions were performed with the model ship installed the shaft forces measuring device using circular motion tester of Samsung Ship Model Basin. Characteristics of the measured shaft forces in model tests show quantitatively good agreement with the computed values obtained by the CFD programs using the measured wake data in oblique towing conditions. In the near future, It is hoped that the estimated shaft forces for a ship from this experimental method could be validated through comparison with directly measured values of a ship.

• Korean Journal of Applied Biomechanics
• /
• v.23 no.4
• /
• pp.295-306
• /
• 2013

The purpose of this study was to provide high school male shot putters training methods of gliding and delivery motion through comparative analysis of kinematic characteristics. To accomplish this purpose, three dimensional motion analysis was performed for the subjects(PKC, KKH, YDL) who participated in high school male shot putter competition on 92nd (2011), 93rd (2013) National Sports Festival. The subjects were filmed by four Sony HXR-MC2000 video cameras with 60 fields/s. The three-dimensional kinematic data of the glide, conversion and delivery phase were obtained by Kwon3d 3.1 version. The data of the shoulder rotational angles and projection angles were calculated with Matlab R2009a. The following conclusions had been made. With the analysis of the gliding and stance length ratio, the gliding length was shorter at the TG than the SG with short-long technique but the gliding and stance length ratio was 46.8:53.2% respectively. The deviation of the shots trajectory from APSS(Athlete-plus-shot-system) revealed that the PKC showed similar to "n-a-b-c-I" of skilled S-shape type, KKH and YDL showed "n-a-d-f-I'" of unskilled type. Furthermore, they showed smaller radial distance from the central axis of the APSS and the shots were away from the linear trajectory. From this characteristics, The PKC who performed more TG than SG had shorter glide with S-shape of APSS(skilled type) showed the better record than others with technical skill. But KKH and YDL had bigger glide ratio with "n-a-d-f-I'" of unskilled type and improved their records with technical factor. The projection factor had an effect on the record directly. Because PKC maintained more lower glide and transition posture with momentum transfer through COG's rapid horizontal velocity respectively the subject possessed the characteristics of high horizontal and vertical velocity with large turning radius from shot putter to APSS.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.546-550
• /
• 2008

In this study, 3-dimensional Computational Fluid Dynamics (CFD) analysis was induced to simulate air flow and particle motion in the axial flow cyclone separator. The commercialized CFD code FLUENT was used to visualize pressure drop and particle collection efficiency inside the cyclone. We simulated 4 cyclone models with different shape of vane, such as turning angle or shape of cross section. For the air flow simulation, we calculated the flow field using standard ${\kappa}-{\varepsilon}$ turbulence viscous model. Each model was simulated with different inlet or outlet boundary conditions. Our major concern for the flow filed simulation was pressure drop across the cyclone. For the particle trajectory simulation, we adopted Euler-Lagrangian approach to track particle motion from inlet to outlet of the cyclone. Particle collection efficiencies of various conditions are calculated by number based collection efficiency. The result showed that the rotation angle of the vane plays major roll to the pressure drop. But the smaller rotation angle of vane causes particle collection efficiency difference with different inlet position.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.1
• /
• pp.515-520
• /
• 2020

The design and actual implementation of the four-bar parallel link was studied in the paper. The parallel four-section link is widely used as a basic kinematic mechanism for transmitting the rotation of one axis to the rotational motion of the other axis. However, the parallel 4 link has a problem that phase reversal occurs at the turning point during the movement. In order to prevent the link reversal, it is known that a double parallelogram-type link is formed by attaching an additional phase reversal suppression link with an offset. However, as a result of the actual fabrication experiment, the movement is not smooth at the transition point. In order to solve this problem, in this study, a link for smooth movement is added in addition to a link that provides an offset to prevent phase reversal, so that the phase reversal does not occur at a specific point when the driven shaft rotates along the drive shaft. The test result confirms the validity of our suggestion.

• Journal of the Society of Naval Architects of Korea
• /
• v.32 no.4
• /
• pp.19-26
• /
• 1995

The assessment of maneuverability of a ship is very important from the view point of safety of human beings and of pollution of ocean. And, it is quite natural that every ship yard wants to have some tools with which they can build a ship with good maneuverability. But, maneuvarability of a ship is very subtle problem, and to calculate the exact maneuvering motion, lots of captive model tests must be carried out. Futhermore, in the initial design stage we can not make the scale model, because the lines of a ship is not fixed. In this paper, some approximate method to calculate the maneuvering motion of a ship, with the principal dimensions of hull, and propeller, rudder characteristics only, is studied. And, proposed approximate method is used to calculate the turning and zig-zag maneuver of several ships. The results of those calculations and the usability of the method are discussed.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.5
• /
• pp.262-270
• /
• 2022

The emergence of new concept ships, such as autonomous ships, has drawn much attention on the manoeuvrability of ships because of the safe navigation and operation of ships. Although the manoeuvrability of KRISO Container Ship(KCS) has been frequently reported, there have been few documents of representative manoeuvre cases conducted in various methods by one institute. This paper presents the manoeuvrability of the ship in 1/42.0 model scale by 3 methods: free running model tests, horizontal planar motion mechanism tests, and computational fluid dynamics analysis. KRISO reports KCS manoeuvre data: 35° turning circle tests and 20/20(10/10) zigzag manoeuvring tests. In addition, a simple formula for integrating and comparing manoeuvre indices, Manoeuvrability Comparing Simple Index(MCSI), is proposed.

• Journal of Positioning, Navigation, and Timing
• /
• v.2 no.2
• /
• pp.123-130
• /
• 2013

Autonomous agricultural machines that are operated in small-scale farmland frequently experience turning and changes in direction. Thus, unlike when they are operated in large-scale farmland, the steering control systems need to be controlled precisely so that travel errors can be minimized. This study aims to develop a control algorithm for improving the path tracking performance of a steering system by analyzing the effect of the setting of the waypoint, which serves as the reference point for steering when an autonomous agricultural machine moves along a path or a coordinate, on control errors. A simulation was performed by modeling a 26-hp tractor steering system and by applying the equations of motion of a tractor, with the use of a computer. Path tracking errors could be reduced using an algorithm which sets the waypoint for steering on a travel path depending on the radius of curvature of the path and which then controls the speed and steering angle of the vehicle, rather than by changing the steering speed or steering ratio which are dependent on mechanical performance.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.2
• /
• pp.35-44
• /
• 2009

Long stroke Fast Tool Servo (LFTS) with maximum stroke of $432{\mu}m$ is designed, manufactured and tested for fabrication of optical free-form surfaces. The large amount of stroke in LFTS has been realized by utilizing the hinge and lever mechanisms which enable the displacement amplification ratio of 4.3. In this mechanism the peculiar shape was devised for maximizing the displacement of end tip in LFTS and special mechanical spring has been mounted to provide the sufficient preload to the piezoelectric actuator. Also, its longitudinal motion of tool tip can be measured by capacitive type displacement sensor and closed-loop controlled to overcome the nonlinear hysteresis. In order to verify the static and dynamic characteristics of designed LFTS, several features including step response, frequency response and cut-off frequency in closed-loop mode were experimentally examined. Also, basic machining result shows that the proposed LFTS is capable of generating the optical free-form surface as an additional axis in diamond turning machine.

• Journal of Welding and Joining
• /
• v.14 no.6
• /
• pp.68-80
• /
• 1996

When a workpiece is to be arc welded around the outside corner, continuous welding without welding seam in the neighborhood of comer still remains a very difficult technique. Skilled welders weld comers by delicate“hand-eye coordination”while turning the workpiece manually, However, there is not a very clear solution to this problem in robotized arc welding process. In order to solve this problem, the coordination of a robot and a positioner with one or two axes is necessary. This paper presents a method of continuous welding around the corner of workpiece using the coordinated motion of a robot and a positioner. The positioner is either revolute jointed or prismatic jointed. In this paper, a clothoid curve is chosen for welding trajectory. The clothoid curve is excellent in connecting straight and curved weld-lines with good continuity and accommodates various welding conditions. By using this welding trajectory, the deceleration, which leads to widening of the melt and the heat affected zone, at comer area is reduced with strategic rotation of robot torch in coordination with a positioner providing smooth transition of welding torch orientation. Two types of special clothoid curves are developed for different weld slope conditions. These clothoid curves are applied to the case of linear and rotary Positioners at arc welding robot work-cell.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.720-723
• /
• 2005

Ship motion is a complex controlled process with several hydrodynamic parameters that vary in wide ranges with respect to ship load condition, speed and surrounding conditions (such as wind, current, tide, etc.). Therefore, to effectively control ships in a designed track is always an important task for ship masters. This paper presents an effective adaptive autopilot ships that ensure the optimal accuracy, economy and stability characteristics. The PID control methodology is modified and parameters of a PID controller is designed to satisfy conditions for an optimal objective function that comprised by heading error, resistance and drift during changing course, and loss of surge velocity or fuel consumption. Designing of the controller for course changing process is based on the Model Reference Adaptive System (MRAS) control theory, while as designing of the automatic course keeping process is based on the Self Tuning Regulator (STR) control theory. Simulation (using MATLAB software) in various disturbance conditions shows that in comparison with conventional PID autopilots, the designed autopilot has several notable advantages: higher course turning speed, lower swing of ship bow even in strong waves and winds, high accuracy of course keeping, shorter time of rudder actions smaller times of changing rudder direction.