• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.10a
• /
• pp.115-120
• /
• 1992

Mirror-surface machining is very important machining technology to manufacture optical parts. especially brittle materials. In case of optical plastics, it is produced through both grinding and polishing till now. New machining method which is more efficient and contributed to the protection of the environmental pollution is, therefore, studied. In this , experimental results and an analysis of surface roughness in ultrasonic vibration cutting of optical plastic (CR-39) which is used for optical lens is presented. In results, a comparison of the micro-structure of machined surfaces produced by cutting with ultrasonic vibration and conventional turning is presented by analyzing S.E.M. photograph. Also, wavelength spectrum analysis is performed to investigate the surface-characteristics machined by ultrasonic vibration cutting.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.26-30
• /
• 1996

This paper presents the performance of CBN tools in the machining of hardened die-materials, SKD11 and SKD61 steel with HRC 50, by high-speed face milling. Generally, grinding or EDM is being used in machining of hardened materials but the cost is very high. If those can be replaced by cutting, it will be a greatly economical advantage. CBN tool has been recognized as an effective tool in turning, but it has not been in milling. So wear and surface roughness mode of CBN tool for hardened SKD11 and SKD61 steel were investigated by high-speed face milling in this study Also the relation between cutting force and wear mode of CBN tools was investigated.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.11
• /
• pp.76-82
• /
• 1998

In this study, the Ball screw and Servo motor Mechanism is considered as a High Speed Tool Feed System for the machining of a piston of a reciprocating engine. For the machining of a piston, that shapes oval, high speed servo mechanism is needed as a positioning of a cutting tool, and the stroke of tool is 0.1 mm ~ 1 mm. Ball screw and servo motor Mechanism is available very much because this mechanism is used widely in general machine. This Mechanism has been designed with the use of the decrease in mass and partial wear of the ball screw for high speed positioning of tool. Also the periodic learning control method with the inverse transfer function compensation has been applied to the positioning control for the high accuracy positioning of tool. These applications lead the achievement of the machining of a piston with an accuracy of 5${\mu}{\textrm}{m}$ at 2500 rpm in CNC turning.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.152-157
• /
• 1998

Since early 1960s, the high precision machining technology, so called ultra-precision technology or nano technology, has been developed in many Held based on single point diamond turning technology. The major application of this technology is the optical components with aspherical surfaces. Now a days, customer requires the smaller and lighter optical elements, such as camera video and etc., with higher performance for convenience. So, the manufacturer focuses on the ultra-precision technology. Thus, this technology becomes the major target to challenge the advanced barrier for the next machining technology.

• Structural Engineering and Mechanics
• /
• v.61 no.4
• /
• pp.519-526
• /
• 2017

In the present paper, the effects of cutting parameters and coating material on the performances of cutting tools in turning of AISI 52100 steel are discussed experimentally. A comparative study was carried out between uncoated and coated (with TiCN-TiN coating layer) cermet tools. The substrate composition and the geometry of the inserts compared were the same. A mathematical model was developed based on the Response Surface Methodology (RSM). ANOVA method was used to quantify the effect of cutting parameters on the machining surface quality and the cutting forces. The results show that feed rate has the most effect on surface quality. However, cutting depth has the significant effect on the cutting force components. The effect of coating layers on the surface quality was also studied. A lower surface roughness was observed when using PVD (TiCN-TiN) coated insert. A second order regression model was developed and a good accuracy was obtained with correlation coefficients in the range of 95% to 97%.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.11
• /
• pp.905-910
• /
• 2016

Infrared (IR) optic lens can be fabricated by a single point diamond turning (SPDT) machine without subsequent polishing process. However, this machining process often leaves micro-cracks that deteriorate the surface quality. In this work, we propose an experimental design to remove micro-cracks on IR lens. The proposed design gathered data between cutting process condition and Rt surface roughness. This is of great importance because the scale of micro-cracks is a few micrometer. Rt surface roughness is suitable for analyzing maximum peak height signals of the profile. The experimental results indicate that feed per revolution variable is one of the most dominant variable, affecting the generation micro-cracks on IR lens surfaces.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.99-107
• /
• 1995

This paper reported research results to develop an algorithm of on-lin evaluation of surface profiles and roughness generated by turning. The developed module consisted of computer simulation of surface profiles using mechanism of cutting mark formation and cutting vibrations, and online measurement of cutting vibrations. The relative cutting vibrations between tool and worpkiece were measured through an inductance pickup at the rate of one sample per rotation of the workpiece. The sampling process was monitored using an encoder to avoid conceling out the phase lag between waves. The digital cutting signals from the Analog-to-Digital converter were transferred to the simulation module of surface profile where the surface profiles were generated. The developed algorithm or surface generation in a hard turning was analyzed through computer simulations to consider the stochastic and dynamic nature of cutting process. Cutting tests were performed using AISI 304 Stainless Steel and carbide inserts in practical range of cutting conditions. Experimental results showed good correlation between the surface profiles and roughness obtained using the developed algorithm and the surface texture measured using a surface profilemeter. The research provided the feasibility to monitor surface characteristics during tribelogical tests considering wear effect on surface texture in machining.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.3
• /
• pp.183-189
• /
• 2013

The chalcogenide glass has superior optical properties in IR region transmittances. We have determined the composition of GeSbSe chalcogenide glass for the application of good IR lenses, resulting in the composite rate of $Ge_{19}Sb_{23}Se_{58}$. The optical, structural, thermal and physical properties were measured by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), Differential scanning calorimeter (DSC), X-ray computed tomography (X-ray CT) respectively. The fabrication of the chalcogenide glass lens for infrared optics applications was proposed using a diamond turning machining technology which is known as the suitable ways for the production cost reduction and the accurate fabrication process control.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.1
• /
• pp.85-91
• /
• 2013

The machinability of wear-resistible tungsten carbides and the tool wear behavior in machining of V30 and V50 tungsten carbides using PCD (Poly Crystalline Diamond) cutting tool was investigated to understand machining characteristics. This material is one of the difficult-to-cut materials in present, but their usage has been already broadened to every commercial applications such as mining tools, and impact resistant tools etc. Summary of the results are as follows. (1) Tool wear progression of PCD tools in turning of wear-resistible tungsten carbides were observed specially fast in primary cutting distance within 10m. (2) Three components of cutting resistance in this research were different in balance from the ordinary cutting such as that cutting of steel or cast iron. Those were expressed large value by order of thrust force, principal force, feed force. (3) If presume from viewpoint of high efficient cutting within this research, a proper cutting speed was 15m/min and a proper feed rate was 0.1mm/rev. In this case, it was found that the tool life of PCD tool was cutting distance until 230m approximately. (4) In cutting of wear-resistible tungsten carbides such as V30 and V50, it was recognized that the tool wear rate of V30 was very fast as compared with V50. (5) When the depth of cut was 0.1mm, there was no influence of the feed rate on the feed force. And the feed force tended to decrease as the cutting distance was long, because the tool was worn and the tool edge retreated. (6) It was observed that the tungsten carbides were adhered to the flank.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1456-1464
• /
• 1993

The achievable machining accuracy depends upon the level of the micro-engineering, and the dimensional tolerances in the order of 10 nm and surface roughness in the order of 1 nm are the accuracy targets to achieved today. Such requirements cannot be satisfied by the conventional machining processes. Single point diamond turning is one of the new techniques which can produce the parts with such accuracy limits. The aims of this thesis are to get a better understanding of the complex cutting forces. A cutting model for describing the influence of cutting conditions (cutting speed, feedrate and depth of cut), material properties of the workpiece and tool geometry has been proposed after estimating the two cutting force models-the Recht model and the Dautzenberg model. The experiments with Al-alloy workpieces, which have been carried out in order to estimate the models, show that the proposed model in this thesis is better than the two models. As the depth of cut and feedrate are increased in the operations settings (depth of cut 8-100$\mu{m}$, feedrate 8-140$\mu{m}$/rev, and cutting speed 8 m/sec), the relation of dimensionless cutting forces from experiments are similar to the proposed model. With the undeformed chip area of $30-80{\times}10^{2}$\mu{m}^2$, the experimental cutting forces accord with the force prediction.