• 대한기계학회논문집
• /
• 제16권10호
• /
• pp.1971-1978
• /
• 1992

본 연구에서는 원형 파이프에 원추형 디퓨져가 연결된 덕트 내의 유동장에 대 하여 Launder-Sharma의 저 레이놀즈수 k-.epsilon. 난류모델을 이용하여 수치해석을 수행하였 으며, 수치해석 방법으로는 타원형 방법을 사용하였으며, 앞으로 일반적인 단면의 곡 관이나 스크롤 내부 유동 등의 연구 수행을 감안하여 지배방정식을 일반 비직교 좌표 계로 변환하여 계산을 수행하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2798-2803
• /
• 2008

The confined slot air jet impinging normally on a moving flat surface has been investigated numerically by using commercial CFD code Ansys CFX-V11. Turbulent flows are modeled using k-w turbulence model. Two-dimensional turbulent flow is considered. Calculations were conducted for a nozzle-to-plate spacing of eight slot nozzle width, at three Reynolds number(Re=4500, 6700 and 10,000) and four surface-to-velocity ratios i.e. 0, 0.25, 0.5 and 1. Results are compared against corresponding cases for heat transfer from a stationary plate. Local Nusselt number is calculated under constant wall temperature condition. The analysis reveals that the average Nusselt number increases considerably with the jet exit Reynolds number, but decrease with the plate velocity.

• Journal of Advanced Marine Engineering and Technology
• /
• 제20권5호
• /
• pp.58-67
• /
• 1996

In the present study, the pressure distribution, wall shear stress distribution and friction factor of developing turbulent pulsating flows are investigated theoretically and experimentally in the entrance region of a square duct. The pressure distribution for turbulent pulsating flows are in good agreement with the theoretical values. The time-averaged pressure gradients of the turbulent pulsating flows show the same tendency as those of turbulent steady flows as the time-averged Reynolds number $(Re_{ta})$ increase. Mean shear stresses in the turbulent pulsating flow increase more in the inlet flow region than in the fully developed flow region and approach to almost constant value in the fully developed flow region. In the turbulent pulsating flow, the friction factor of the quasi-steady state flow $({\lambda}_{q, tu})$ follow friction factor's law in turbulent steady flow. The entrance length of the turbulent pulsating flow is not influenced by the time-averaged Reynolds number $(Re_{ta})$ and it is about 40 times as large as the hydraulic diameter.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권3호
• /
• pp.529-561
• /
• 2014

The two-phase turbulent flow past an interface-piercing circular cylinder is studied using a high-fidelity orthogonal curvilinear grid solver with a Lagrangian dynamic subgrid-scale model for large-eddy simulation and a coupled level set and volume of fluid method for air-water interface tracking. The simulations cover the sub-critical and critical and post critical regimes of the Reynolds and sub and super-critical Froude numbers in order to investigate the effect of both dimensionless parameters on the flow. Significant changes in flow features near the air-water interface were observed as the Reynolds number was increased from the sub-critical to the critical regime. The interface makes the separation point near the interface much delayed for all Reynolds numbers. The separation region at intermediate depths is remarkably reduced for the critical Reynolds number regime. The deep flow resembles the single-phase turbulent flow past a circular cylinder, but includes the effect of the free-surface and the limited span length for sub-critical Reynolds numbers. At different Froude numbers, the air-water interface exhibits significantly changed structures, including breaking bow waves with splashes and bubbles at high Froude numbers. Instantaneous and mean flow features such as interface structures, vortex shedding, Reynolds stresses, and vorticity transport are also analyzed. The results are compared with reference experimental data available in the literature. The deep flow is also compared with the single-phase turbulent flow past a circular cylinder in the similar ranges of Reynolds numbers. Discussion is provided concerning the limitations of the current simulations and available experimental data along with future research.

• 한국해양학회지
• /
• 제18권2호
• /
• pp.104-110
• /
• 1983

海洋 亂流境界層內 亂流運動量輸送의 斷續性 現象에 對하여 그 本質을 把握 하고 流體力學的 인 의미를 규명하기 위한 영구를 기원했다.또한 단속성 현상과 작비현상의 상호관계도 아울러 연구했다. 본 연구를 통해 난류경계층내에서도 중간층에 속하는 z/h=0.067층에서는 단속성의 크기가 평균난류운동량 수송의 408배의 달하고 상부층 즉 z/h=0.1층에서는 270배에 달함이 밝혀져,이제까지 보고되었던 Gordon(1974)이나 Heathersaw(1974)의 30배의 월등히 크다는 것이 새로운 사실이다. 일부 학자들은 단속성현상을 자기현상의 반영 또는 자기의 유통계의 부딪혀 나타나는 현상이라고 해석한바 있으나 (Gordon,1974; Heathersaw,1974),본 연구에서 밝혀진바에 의하면,이는 마찰 Reynolds 수가>$10^{5}$인 실제해양의 난류경계층내 난류운동의 특징이라는 사실이다.

• 한국정밀공학회지
• /
• 제6권4호
• /
• pp.43-51
• /
• 1989

Free jet was investigated experimentally and numerically in range of Reynolds number from 9900 to 21000. The working fluid was air; the mean velocity components and turbulent quantities were measured by a hot-wire anemometer. In numerical computations, the governing partial differential equations of elliptic type were solved with conventional k- ${\epsilon}$ turbulence model. The measurements show that the jet increased linearly in flow direction, and that similarity for each turbulent quantity such as Reynolds shear stress, or turbulent kinetic energy was revealed in the fully developed region. The computational results show good agreements with experiments.

• Tribology and Lubricants
• /
• 제35권5호
• /
• pp.300-309
• /
• 2019

Gas foil thrust bearings (GFTBs) support axial loads in oil-free, high speed rotating machinery using air or gas as a lubricant. Due to the inherent low viscosity of the lubricant, GFTBs often have super-laminar flows in the film region at operating conditions with high Reynolds numbers. This paper develops a mathematical model of a GFTB with turbulent flows and validates the model predictions against those from the literature. The pressure distribution, film thickness distribution, load carrying capacity, and power loss are predicted for both laminar and turbulent flow models and compared with each other. Predictions for an air lubricant show that the GFTB has high Reynolds numbers at the leading edge where the film thickness is large and relatively low Reynolds numbers at the trailing edge. The predicted load capacity and power loss for the turbulent flow model show little difference from those for the laminar flow model even at the highest speed of 100 krpm, because the Reynolds numbers are smaller than the critical Reynolds number. On the other hand, refrigerant (R-134a) lubricant, which has a higher density than air, had significant differences due to high Reynolds numbers in the film region, in particular, near the leading and outer edges. The predicted load capacity and power loss for the turbulent flow model are 2.1 and 2.3 times larger, respectively, than those for the laminar flow model, thus implying that the turbulent flow greatly affects the performance of the GFTB.

• 설비공학논문집
• /
• 제11권6호
• /
• pp.855-860
• /
• 1999

An experimental study of jet impingement on the surface with linear temperature gradient is conducted with the presentation of the turbulent characteristics and the heat transfer rates measured when this jet impinges normally to a flat plate. The jet Reynolds number ranges from 30,000 to 90,000, the temperature gradient of the plate is 2~$4.2^{\circ}C$/cm and the dimensionless nozzle to plate distance(H/D) is from 6 to 10. The results show that the peak of heat transfer rate occurs at the stagnation point, and the heat transfer rate decreases as the radial distance from the stagnation point increases. A remarkable feature of the heat transfer rate is the existence of the second peak. This is due to the turbulent development of the wall jet. Maximum heat transfer rate occurs when the axial distance from the nozzle to nozzle diameter(H/D) is 8. The heat transfer rate can be correlated as a power function of Prandtl number, Reynolds number and the dimensionless nozzle to plate distance(H/D). It has been found that the heat transfer rate increases with increasing turbulent intensity.

• Journal of Mechanical Science and Technology
• /
• 제17권7호
• /
• pp.1054-1062
• /
• 2003

The numerical simulations of flow and pollutant particle dispersion are described for two-dimensional bell shaped hills with various aspect ratios. The Reynolds-averaged incompressible Navier-Stokes equations with low Reynolds number $\kappa$-$\varepsilon$ turbulent model are used to simulate the flowfield. The gradient diffusion equation is used to solve the pollutant dispersion field. The code was validated by comparison of velocity, turbulent kinetic energy, Reynolds shear stress, speed-up ratio, and ground level concentration with experimental and numerical data. Good agreement has been achieved and it has been found that the pollutant dispersion pattern and ground level concentration have been strongly influenced by the hill shape and aspect ratio, as well as the location and height of the source.

• 한국항공우주학회지
• /
• 제45권5호
• /
• pp.367-375
• /
• 2017

본 연구에서는 초음속 영역에서의 해머헤드형 노즈 페어링을 포함하고 있는 발사체 선두부에 대한 RANS 전산해석을 수행하였다. 층류, 완전 난류, 천이 모델을 이용한 2차원 축대칭 해석을 수행하여 실험 결과와 비교하였다. 레이놀즈수의 변화에 따라서 다른 유동현상이 나타남을 확인하였다. 높은 레이놀즈수에서는 경계층이 난류가 되어 발사체 표면에서 박리가 되지 않는다. 낮은 레이놀즈수 조건에서는 해머헤드형 노즈 페어링의 팽창-압축 모서리에서 경계층의 박리와 재부착으로 층류 박리 거품이 만들어진다. 받음각이 있는 3차원 계산에서 층류 박리 거품으로 발생되는 와류 구조를 확인할 수 있었다. 레이놀즈수에 따른 박리 거품을 예측하기 위해서 난류 천이를 고려해야 함을 확인할 수 있었다.