• 대한기계학회논문집B
• /
• 제30권4호
• /
• pp.320-327
• /
• 2006

The computations of chemically reacting laminar and turbulent flows are performed using the preconditioned Navier-Stokes solver coupled with turbulent transport and multi-species equations. A low-Reynolds number $k-\varepsilon$ turbulence model proposed by Chien is used. The presence of the turbulent kinetic energy tenn in the momentum equation can materially affect the overall stability of the fluids-turbulence system. Because of this coupling effect, a fully coupled formulation is desirable and this approach is taken in the present study. Choi and Merkle's preconditioning technique is used to overcome the convergence difficulties occurred at low speed flows. The numerical scheme used for the present study is based on the implicit upwind ADI algorithm and is validated through the comparisons of computational and experimental results for laminar methane-air diffusion flame and $ H_2/O_2$ reacting turbulent shear flow. Preconditioning formulation shows better convergence characteristics than that of non-preconditioned system by approximately five times as much.

• 대한안전경영과학회지
• /
• 제14권2호
• /
• pp.83-89
• /
• 2012

In this study, FDS fire simulation experiments and measured wind speed by applying the exterior installation portion for blocking the spread of the fire was investigated. As a result, aluminum composite panels installed in the lower and the upper part of the panel to remove all the lower side, and then the maximum wind speed 0.24 m/s and the upper side 0.58 m/s were measured. In the FDS, the measured wind speed difference air currents are approximately 3.7 times in 12 seconds, the occurrence of 17 seconds early moment wind 2.2 m/s was measured from. Before and after the fire occurred in early of the air velocity about 39 seconds was 3.5 times difference. Such air currents caused by the temperature of the building but also by the building height was found. Turbulent flame of fire by expanding the vertical extent of damage become greatly important factor. Therefore, through the exterior installation portion of the block that can delay the spread of fire is expected that this should be taken.

• 한국자동차공학회논문집
• /
• 제8권2호
• /
• pp.50-56
• /
• 2000

It is well known that the combustion phenomenon of diesel engine is an unsteady turbulent diffusion combustion. Therefore, the combustion performance of diesel engine is related to a complex phenomenon which involves the various factors of combustion, such as a injection pressure, injection timing, injection rate, and operation conditions of engine. In this study, the spray and the flame development processes in a single cylinder D.I. diesel visualization engine which uses the electronically controlled injection system were visualized to interpret the complicated combustion phenomenon by using high speed CCD camera. In addition, the cylinder pressure and heat release rate were also obtained in order to analyze the diesel combustion characteristics under several engine conditions.

• 대한기계학회논문집
• /
• 제18권7호
• /
• pp.1789-1798
• /
• 1994

This paper aimed for numerical simulation of complicated gas turbine combustor with swirler. For the convenience of numerical analysis, fuel nozzle and air linear hole areas of secondary and dilution zone, which are issued to jet stream, were simplified to equivalent areas of annular type. In other to solve these problems, imaginary source terms which are corresponded to supplied fuel amount were added to those of governing equation. Chemical equilibrium model of infinite reaction rate and $k-{\epsilon}-g$ model with the consideration of density fluctuation were applied. As the result, swirl intensity contributed to mixing of supplied fuel and air, and to speed up the flame velocity than no swirl condition. Temperature profiles were higher than experimental results at the upstream and lower at the downstream, but total energy balance was accomplished. As these properties showed the similar trend qualitatively, simplified simulation method was worth to apply to complicated combustor for predicting combustion characteristics.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.590-593
• /
• 2009

모델 스크램제트 엔진의 3차원 유동특성 이해를 위하여 다단의 충격파를 발생 시키는 흡입구부터(외부 유동영역) 공동형 보염기, 연소기, 노즐이 포함되는 엔빈 내부 전영역을 통합한 수치해석을 수행하였다. $k-{\omega}$ SST 난류모델과 Sarkar모델이 적용된 저 레이놀즈 수 k-e 난류모델의 해석결과를 실험 결과와 비교하였으며, 흡입구의 측면효과(intake side wall effects)를 살펴보기 위하여 측면의 유무에 따른 유동특성을 관찰하였다. 본 연구에 소요되는 계산시간의 효율성을 위하여 계산영역을 다중블럭으로 구성하였으며, MPI(Massage Passing Interface) 병렬 계산 기법을 적용하였다.

• 대한기계학회논문집
• /
• 제18권4호
• /
• pp.912-919
• /
• 1994

The engine combustion is one of the most important processes affecting performance and emissions. One effective way to improve the engine combustion is to control the motion of the charge inside a cylinder by means of optimum induction system design, because the flame speed is mainly determined by the turbulence at compression(TDC) process in S.I. engine. It is believed that the tumble and swirl motion generated during intake stroke breaks down into small-scale turbulence in the compression stroke of the cycle. However, the exact nature of this relationship is not well known. This paper describes the tumble flow measurements inside the cylinder of a 4-valve S.I. engine using laser Doppler velocimetry(LDV) under motoring(non-firing) conditions. This is conducted on an optically assesed single cylinder research engine under motored conditions at an engine speed of 1000rpm. Three different cylinder head intake port configurations are studied to develop a better understanding the tumble flow generation, development, and breakdown mechanisms.

• Korean Chemical Engineering Research
• /
• 제62권1호
• /
• pp.27-35
• /
• 2024

메탄, 프로판 등을 주성분으로 하는 연료가스는 폭발위험장소에서 사용될 수 있으며, 누출로 인한 공정조건의 영향으로 불균일한 혼합기를 형성할 수 있다. 균일한 혼합기를 대상으로 측정된 문헌 데이터를 이용한 화재 폭발 위험성 평가, 손상 예측은 가스 누출에 의한 실제 폭발 사고와 다른 결과를 얻을 수 있다. 본 연구에서는 가스 누출시 나타날 수 있는 농도 변화에 있어서 불균일성 혼합기의 폭발압력, 화염속도 등의 폭발특성을 조사하였다. 길이 0.82 m의 스테인리스 재질의 밀폐 배관에서 수행하였으며 컬러 초고속 카메라 및 압력 센서를 사용하여 관찰하였다. 또한 배관 내의 시간에 따른 농도차이 변화에 대해 회귀분석 모델을 사용하여 불균일 혼합물의 정량화 방법을 제안하였다. 본 연구의 농도 불균일성 조건에 있어서 메탄 폭발 시 전파화염은 불균일성 농도가 높아짐에 따라 화염 면적의 증가가 관찰되었고 이는 난류 화염의 주름진 화염 구조와 유사하였다. 메탄의 최대압력까지 걸리는 소요시간은 불균일성이 클수록 감소하였고, 폭발압력은 불균일성이 클수록 증가하였다. 농도가 불균일한 메탄의 K_G(폭연지수)의 범위는 1.30~1.58 [MPa·m/s]으로서 메탄의 농도가 균일성에서 불균일성로 변화하면서 17.7% 증가하였다.

• 한국화재소방학회논문지
• /
• 제26권2호
• /
• pp.90-96
• /
• 2012

외장재에 의한 수직화재확산은 확산속도가 구획화재에 비해 매우 빨라 이에 대한 화재의 특성 분석이 요구된다. 본 연구에서는 건물 외부에서 발생한 화재가 연소 확대되면서 수직으로 상승하여 개구부를 통해 유입되는 화재의 성상에 대해서 외장재로 널리 사용되는 심재가 폴리에틸렌인 일반 알루미늄복합패널에 대해 화재시뮬레이션을 적용하여 연구하였다. 그 결과, 수직확산화염은 화재초기에 2층까지 상승하는 데는 약 135초가 걸렸지만 10층까지는 470초, 최고층인 30층까지 상승하는 데는 711초에 도달하는 것으로 분석되어 고층부로 갈수록 난류 및 외장재 설치공간의 연돌효과에 의해서 급격히 확대되는 것을 알 수 있었다. 이러한 연구 결과로 외장재가 설치된 건축물의 화재 시 개구부를 통한 화재는 동시다발적으로 그 건물의 내부에 확대되는 심각성을 확인할 수 있었다.

• 대한기계학회논문집
• /
• 제18권4호
• /
• pp.920-932
• /
• 1994

The combustion phenomena of a reciprocating engine is one of the most important processes affecting performance and emissions. One effective way to improve the engine combustion is to control the motion of the charge inside a cylinder by means of optimum induction system design, because the flame speed is mainly determined by the turbulence at compression(TDC) process in S.I. engine. It is believed that the tumble and swirl motion generated during intake breaks down into small-scale turbulence in the compression stroke of the cycle. However, the exact nature of their relationship is not well known. This paper describes cycle resolved LDV measurement of turbulent flow inside the cylinder of a 4-valve engine under motoring(non-firing) conditions, and studies the effect of intake port configurations on the turbulence characteristics using following parameters ; Eulerian temporal autocorrelation coefficient, turbulence energy spectral density function, Taylor micro time scale, integral time scale, and integral length scale.

• 한국자동차공학회논문집
• /
• 제4권3호
• /
• pp.211-219
• /
• 1996

In a small high-speed D. I. diesel engine, the injected fuel spray into the atmosphere of the high temperature is burnt by go through the process of break up, atomization, evaporation and process of ignition. These process are important to decide the emission control and the rate of fuel consumption and out put of power. Especially, in the case of injected fuel spray impinging on the wall of piston cavity, the geometry of piston cavity gives great influence the ignitability of injected fuel and the flame structure. Ordinary, the combustion chamber of driving engine have unsteady turbulent flow be attendant on such as the change of temperature, velocity and pressure. So the analysis of spray behavior is difficult. In this study, the spray was impinged on the wall of 3 types of piston cavity such as Dish, Toroidal, Re-entrant type, in order to analyze the combustion process of impinging spray precisely and systematically. And hot wire probe was used for analyze non-steady flow characteristics of impinging spray, and to investigate the behavior of spray, the aspects of concentration c(t), standard deviation σ(t) and variation factor(vf) was measured with the lapse of time.