• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1453-1460
• /
• 2003

The present study investigates the effects of rib arrangements and aspect ratios of a rectangular duct simulating the cooling passage of a gas turbine blade. Two different V-shaped rib configurations are tested with the aspect ratios (W/H) of 3 to 6.82. One is the continuous V-shaped rib configuration with $60^{\circ}$ attack angle, and the other is the discrete V-shaped rib configuration with $45^{\circ}$ attack angle. The square ribs with the pitch to height ratio of 10.0 are installed on the test section in a parallel arrangement for both rib configurations. Reynolds numbers based on the hydraulic diameter are changed from 10,000 to 30,000. A naphthalene sublimation method is used to measure local heat/mass transfer coefficients. For the continuous V-shaped rib configuration, two pairs of counter-rotating vortices are generated in a duct, and high transfer region is formed at the center of the ribbed walls of the duct. However, for the discrete V-shaped rib configuration with $45^{\circ}$ attack angle, complex secondary flow patterns are generated in the duct due to its geometric feature, and more uniform heat/mass transfer distributions are obtained for all tested cases

• Membrane and Water Treatment
• /
• v.7 no.3
• /
• pp.175-191
• /
• 2016

In this work, oil-in-water emulsions (O/W) were prepared successfully by membrane emulsification with $0.5{\mu}m$ pore size membrane. Sunflower oil was emulsified in aqueous Tween80 solution with a simple crossflow apparatus equipped with ceramic tube membrane. In order to increase the shear-stress near the membrane wall, a helical-shaped reducer was installed within the lumen side of the tube membrane. This method allows the reduction of continuous phase flow and the increase of dispersed phase flux, for cost effective production. Results were compared with the conventional cross-flow membrane emulsification method. Monodisperse O/W emulsions were obtained using tubular membrane with droplet size in the range $3.3-4.6{\mu}m$ corresponded to the membrane pore diameter of $0.5{\mu}m$. The final aim of this study is to obtain O/W emulsions by simple membrane emulsification method without reducer and compare the results obtained by membrane equipped with helix shaped reducer. To indicate the results statistical methods, $3^p$ type full factorial experimental designs were evaluated, using software called STATISTICA. For prediction of the flux, droplet size and PDI a mathematical model was set up which can describe well the dependent variables in the studied range, namely the run of the flux and the mean droplet diameter and the effects of operating parameters. The results suggested that polynomial model is adequate for representation of selected responses.

• Solar Energy
• /
• v.13 no.1
• /
• pp.11-21
• /
• 1993

The purpose of this study was to investigate the enhancement of heat transfer without additional external power in the case of rectangular impingement air jet vertically on the flat heating surface. The technique used in the present study was placement of square rod bundles as a turbulence promoter in front of the heat transfer surface. The results obtained through this study were summerized as follws. High heat transfer enhancement was achieved by inserting rods in front of the heating flat plate. According to visulaization, it was examined because of flow acceleration and separation and disturbance of boundary layer. The smaller clerance between rod and heating plate was, the larger heat transfer effect became at each H/B. Arverage Nusselt number reached maximum at H/B=10 and the local augmentation rate of heat transfer became maximum at H/B=2. The maximum average heat transfer enhancement rate increase about 43% for the case of X/B=2 and C=1mm, compared to a flat plate without rods. The correlating equation of average Nusselt number and Reynolds number was obatined. As follws : ${\overline{Nu}}_0=1.249Re^{0.465}(C/A)^{-0.033}(H/B)^{0.013}$.