• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.65-73
• /
• 2007

The use of an Exhaust Gas Recirculation(EGR) for a diesel engine with variable geometry turbocharger(VGT) has confronted how to obtain the amount of EGR for NOx reduction requirement at wide operating range and less side effect. Through a combined effort of modeling(wave action simulation) and experiment, an investigation into the effect of EGR area ratio and pipe length on EGR characteristics of common rail diesel engine with VGT has been performed. For accurate computation, calibration of constants involved in empirical and semi-empirical correlations has been performed at a specific operating point, before of its use for engine simulation. From the results of this study, it was found that EGR rate is sharply increased with increasing EGR area ratio until area ratio of 0.3. However, the effect of EGR area ratio on EGR rate is negligible beyond this criteria. This study also investigates the effect of EGR pipe length on a EGR amount and pulsating flow characteristics at EGR junction. The results showed that the longer EGR pipe length, the lower EGR amount was achieved due to the flow loss resulting in lower amplitude of pressure wave.

• 한국대기환경학회지
• /
• 제7권1호
• /
• pp.31-40
• /
• 1991

This study shows the correlation between $NO_x$ emission in the exhaust gas and various operation factors of dual fuel engine for Co-generation system. General tendency was shown that the thermal efficiency was lowered by the change of operation factors. However these were not confirmed on this experiment. Increasing T4 temperature (exhaust gas temperature at turbo-charger inlet) reduces $NO_x$ emission rate. The higher T4 temperature requires lower excess air as the excess air ratio is controlled by T4 temperature on gas mode operation. Another tendency was that $NO_x$ emission rate is reduced in case of increasing boost air temperature, quantity of pilot oil or bypassing flue gas through the exhaust gas boiler. The diameter of the fuel injection nozzle was changed smaller than design value and the injection timing was readjusted. Thus $NO_x$ emission rate could be reduced as retarding injection timing and changing hole diameter of fuel injection nozzle, however maxium engine out-put was decreased by changing fuel nozzle on the diesel mode operation.

• 오토저널
• /
• 제7권4호
• /
• pp.24-31
• /
• 1985

본 논문은 Comprex압력파 과급기(Pressure-wave Supercharger;이하 PWS)의 공기 역학적인 원 리에 대해 기술하였으며, 또 기체 동력학적인 현상들이 별도의 제어장치없이도 우수한 운전성과 낮은 연료소모율, 적은 배기 배출물을 형성하는 차량들에 대해 기계적으로는 간단하면서도 완벽 한 boosting장치를 만들어 내는데 어떻게 사용될 수 있는지를 설명하였다. 근본적인 목적은 종 래의 turbo charger와 동일이지만 Comprex PWS는 현재 응용되고 있는 승용차가 요구하는 여러 가지면, 즉 1) 부하변동에 대한 충진공기압의 빠른 응답성 2) 엔진속도 전영역에 걸친 높은 boost 효과 3) 배기배출물특성을 좋게할 수 있는 배기가스 재순환(EGR)효과 등에서 종래의 것과 구별된다. 따라서 PWS의 중요한 특징들을 기술하였으며 마지막으로 최근 자동차용 Diesel Engine에의 몇 가지 예를 보았다.

• 한국자동차공학회논문집
• /
• 제15권6호
• /
• pp.151-158
• /
• 2007

The static and dynamic behaviour of VGT and EGR systems has a significant impact on overall engine performance, fuel economy and exhaust emissions. This is because they define the state and composition of the air charge entering the engine. This work focused on the effect of the aperture ratio of VGT and EGR on the emission and flow characteristics under partial loads conditions. The investigation carried out using 2 liter PCCI 4 cylinder diesel engine with VGT and EGR. The result of this study shows that smoke increases with increasing EGR rate and NOx decreases with increasing EGR rate. It was also found that the residual gas contents greatly impact on soot emission under partial load condition. Finally, it can be concluded that VGT and EGR aperture ratio can greatly impact not only on soot and NOx but also air charging.

• 대한기계학회논문집B
• /
• 제33권2호
• /
• pp.79-84
• /
• 2009

Turbocharger has been widely used in many passenger cars in application with diesel engines because of high power and fuel efficiency. However, flow-induced noise (whoosh or hissing noise) which is generated within a compressor during its operation at marginal surge line can deteriorate noise characteristics. Hissing noise excitation is associated with the generation of turbulence within the turbocharger compressor and radiated through the transmission path in a turbocharger system. In this study, a expansion muffler with lids is devised and installed in the transmission path to reduce the hissing noise. Acoustic and fluid dynamic characteristics for the muffler are investigated which are related to the unsteadiness of turbulence and pressure in the turbocharger system. A transfer matrix method is used to analyze the transmission loss of the muffler. A simple expansion muffler with lids is proposed for the reduction of high frequency component noise. Turbulence simulation is carried out by a standard k - ${\varepsilon}$ model. An optimal design condition of the muffler is obtained by extensive acoustic and fluid dynamic analysis on the engine dynamometer with anechoic chamber. A significant reduction of the hissing noise is achieved at the optimal design of the muffler as compared with the conventional muffler.

• 해양환경안전학회지
• /
• 제27권2호
• /
• pp.355-362
• /
• 2021

L.P SCR의 촉매 반응을 위해 선박의 발전기용 4행정 디젤엔진의 배기가스 온도를 높게 설계 할 수밖에 없었다. 본 연구의 목적은 밸브개폐시기와 연료분사시기를 조정을 통한 배기가스의 온도 감소가 L.P SCR의 운전조건을 만족시키고 고온으로 인한 발전기 엔진의 사고를 예방하기 위함이었다. 배기가스 온도를 하강시키기 위해 캠샤프트의 각도를 조정하고 연료분사펌프의 Shim을 추가하였다. 그 결과 최대폭발압력은 12.8 bar 증가하였고 터보차저 출구온도 평균값은 13.3 ℃ 하강하였다. 터보차저 출구에서 SCR 입구까지의 열손실을 감안하더라도 L.P SCR 운전조건인 SCR 챔버 입구 온도인 290 ℃를 만족하였다. 배기가스 온도 하강을 통해 디젤발전기의 안전운전이 가능하게 한 연구였다.

• 한국자동차공학회논문집
• /
• 제20권5호
• /
• pp.145-151
• /
• 2012

New design of catalytic converter is proposed by optimization of DFSS (Design For Six Sigma) and DOE (Design Of Experiment) method which is based on taguchi matrix. As a result of the optimization of design of catalytic converter, this paper classifies Exhaust-downpipe shapes with 3 parameters to increase flow velocity uniformity of front catalytic substrate face from CFD results. after finishing with L9 Taguchi test matrix, it can be found the main effect of each design parameter of concept model, and optimal design level. in conclusion, it can be increase flow uniformity from 0.60 upto 0.80 with optimal diffuser shape for Turbo-charger.

• 해양환경안전학회지
• /
• 제22권5호
• /
• pp.547-553
• /
• 2016

선박용 디젤엔진 배기가스에 포함된 입자상물질(PM) 가운데서 블랙카본(BC)은 극지방의 해빙을 촉진시키고 온난화를 유발하는 원인물질로서 큰 주목을 받고 있다. 본 연구에서는 향후 예상되는 PM/BC 배출 규제에 선제적으로 대응하고, 저감기술 개발 및 실증을 위한 기초연구의 일환으로 한국해양대학교 실습선 한바다호를 이용하여 실제 운항 중에 주기관의 배기관 수 포인트에서 PM을 샘플링하여 HR-TEM을 통해 그 구조와 특성을 분석하였다. 또한 배기가스 분석기를 이용하여 운전조건별 배기가스 내 유해물질의 배출 경향을 확인하였다. 분석 결과 엔진에서 배출된 PM의 구조는 구형 입자들의 촘촘하지 않은 체인형 결합으로 이루어져 있으며, 과급기로부터 멀어질수록 온도 저하에 의한 응집이 더 많이 관찰되었고 BC 특유의 graphitic 구조를 잃어가면서 점점 amorphous 구조를 띠는 경향이 나타났다. 또한 배기가스 분석을 통해 엔진 회전수가 증가할수록 배기 내 PM의 농도는 감소할 것으로 예측되었다.