• Journal of Korean Society of Transportation
• /
• v.17 no.1
• /
• pp.67-74
• /
• 1999

Where an interchange is located just after a tunnel not only it is impossible to install the traffic signs in tunnel sections but also sufficient sight distance to identify the interchange can't be provided. The objective of this study is to suggest the safety based spacing between tunnel and interchange. For this study accident rate was used as an index representing characteristics for vehicle operation to suggest the appropriate spacing. Traffic volume and the number of accidents on freeway from 1992 to 1997 were analyzed. The relationship between accident rate and spacing represents negative logarithm function such that shorter spacing increases accident rate. An appropriate safety based spacing between tunnel and interchange for four lane freeway with the design speed of 100kph was found as 2.6km.

• Geomechanics and Engineering
• /
• v.11 no.2
• /
• pp.269-288
• /
• 2016

The jointed rock mass behavior often plays a major role in the design of underground excavation, and their failures during excavation and in operation, are usually closely related to joints. This research attempts to evaluate the effects of two basic geometric factors influencing tunnel behavior in a jointed rock mass; joints spacing and joints orientation. A hybridized indirect boundary element code known as TFSDDM (Two-dimensional Fictitious Stress Displacement Discontinuity Method) is used to study the stress distribution around the tunnels excavated in jointed rock masses. This numerical analysis revealed that both the dip angle and spacing of joints have important influences on stress distribution on tunnel walls. For example the tensile and compressive tangential stresses at the boundary of the circular tunnel increase by reduction in the joint spacing, and by increase the dip joint angle the tensile stress in the tunnel roof decreases.

• Geomechanics and Engineering
• /
• v.36 no.1
• /
• pp.71-81
• /
• 2024

This study analyzes the pull-out behavior of tunnel-type anchorage under various joint conditions, including joint direction, spacing, and position, using a finite element analysis. The validity of the numerical model was evaluated by comparing the results with a small-scaled model test, and the results of the numerical analysis and the small-scaled model test agree very well. The parametric study evaluated the quantitative effects of each influencing factor, such as joint direction, spacing, and position, on the behavior of tunnel-type anchorage using pull-out resistance-displacement curves. The study found that joint direction had a significant effect on the behavior of tunnel-type anchorage, and the pull-out resistance decreased as the displacement level increased from 0.002L to 0.006L (L: anchorage length). It was confirmed that the reduction in pull-out resistance increased as the number of joints in contact with the anchorage body increased and the spacing between the joints decreased. The pull-out behavior of tunnel-type anchorage was thus shown to be significantly influenced by the position and spacing of the rock joints. In addition, it is found that the number of joints through which the anchorage passes, the wider the area where the plastic point occurs, which leads to a decrease in the resistance of the anchorage.

• Tunnel and Underground Space
• /
• v.14 no.6 s.53
• /
• pp.429-439
• /
• 2004

The deep underground High Level Waste (HLW) repository to dispose of 36,000tons of spent fuel from the reactors in Korea needs about $4km^2$ repository area. In this study, the deep undergrond repository layout was optimized to minimize the excavation rock volume as well as underground repository area. In the optimization, the results from thermal analysis were used to define the influence of tunnel and deposition hole spacings on repository layout. The repository area and excavation rock volume could be reduced with longer disposal tunnel length. When it is necessary to reduce the repository area with satisfying thermal criteria, it is better to reduce tunnel spacing and increase deposition hole spacing. In contrast, the excavation rock volume can be reduced by increasing the tunnel spacing and decreasing the hole spacing.

• Nuclear Engineering and Technology
• /
• v.40 no.5
• /
• pp.429-438
• /
• 2008

The objective of the present study is the depth and layout optimizations of a single layer, high level radioactive waste repository in a discontinuous rock mass with special joint set arrangements. A single layer repository model, considering variations in the repository depths, pitches, and tunnel spacings, is used to analyze the thermomechanical interaction behavior. It is assumed that the repository is constructed in saturated granite with joints; the PWR spent fuel in a disposal canister is installed in a deposition drift which is then sealed with compacted bentonite; and the backfill material is filled in the repository tunnel. The decay heat generated by the high level radioactive wastes governs the thermomechanical behavior of the near field rock mass of the repository. The temperature and displacement behavior of the repository is influenced more by the pitch variations than the tunnel spacing and repository depth. However, the stress behavior is influenced more by the repository depth variations than the pitch and tunnel spacing. For the final selection of the tunnel spacing, pitch, and repository depth, other aspects such as the nuclide migration through a groundwater flow path, construction costs, operation costs, and so on should be considered.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.65-68
• /
• 2006

Experiments were performed to investigate the effects of mud-flap width on the aeroacoustic noise generation inside high-speed trains. The open-circuit type wind tunnel was used. The measurement setup was custom-built to simulate intercoach spacing. From the measurements, the characteristics of the turbulent flow after the intercoach spacing and consequent generation of aeroacoustic noise inside the cabin was investigated. Especially the effects of mud flap length on the characteristics of the characteristics of the turbulent flow were identified. The mechanism of noise generation by analyzed interactions with structure vibration characteristics and generation characteristics of blocked pressure was investigated.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.3 no.4
• /
• pp.349-358
• /
• 2005

In this study, analysis of the disposal tunnel spacing and disposal pit pitch was carried out, as a factor of the design to estimate the scale and layout of the repository. To do this, based on the reference repository concept and the engineered barrier concept, several cross sections of the disposal tunnel and disposal pit were established. After then, the mechanical and thermal stabilities of the established tunnels were analyzed. Also, an optimized disposal tunnel spacing and the disposal pit pitch reducing the excavation volume was proposed. The results of these analyses can be used in the deep geological repository design. The detailed analyses by the exact site characteristics data to reduce the uncertainty of the site and the modification for the optimization are required.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.4 no.4
• /
• pp.393-400
• /
• 2006

In design of a deep geological repository for the high level wastes, it is very important that the temperature of the bentonite block should not be over $100^{\circ}C$ to maintain the integrity of the bentonite buffer block from the decay heat. In this study, for the layout of the repository to meet the requirement, the analysis of the disposal tunnel and disposal pit spacing was carried out. To do this, based on the reference repository concept, several cases of cooling times and disposal tunnel and disposal pit spacing were compared. The thermal stabilities of the disposal systems were analyzed in terms of the cooling time and spacing. The results showed that it was more desirable to determine the layout of the repository in terms of disposal pit spacing than the disposal tunnel spacing. The results of these analyses can be used in the deep geological repository design. The detailed analyses with the exact site characteristics data will reduce the uncertainty of the results.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.315-321
• /
• 2003

In this study, analysis of the disposal tunnel spacing and disposal pit pitch was carried out, as a factor of the design to estimate the scale and layout of the repository To do this, based on the reference repository concept and the engineered barrier concept, the cross section of the disposal tunnel and disposal pit are established and the mechanical and thermal stabilities of the tunnels are analyzed. Also, the optimized disposal tunnel spacing and the disposal pit pitch which minimize the excavation volume was proposed. The detailed analyses by the exact site characteristics data are needed to reduce the uncertainty of the site in the future.

• Wind and Structures
• /
• v.1 no.3
• /
• pp.225-241
• /
• 1998

The high-rise supporting towers of long-span suspension and cable-stayed bridges commonly comprise a pair of slender prisms of roughly square cross-section with a center-to-centre spacing of from perhaps 2 to 6 widths and connected by one or more cross-ties. The tower columns may have a constant spacing as common for suspension bridges or the spacing may reduce towards the top of the tower. The present paper is concerned with the aerodynamics of such towers and describes an experimental investigation of the overall aerodynamic forces acting on a pair of square cylinders in two-dimensional flow. Wind tunnel pressure measurements were carried out in smooth flow and with a longitudinal intensity of turbulence 0.10. Different angles of attack were considered between $0^{\circ}$ and $90^{\circ}$, and separations between the two columns from twice to 13 times the side width of the column. The mean values of the overall forces proved to be related to the bias introduced in the flow by the interaction between the two cylinders; the overall rms forces are related to the level of coherence between the shedding-induced forces on the two cylinders and to their phase. Plots showing the variation of the force coefficients and Strouhal number as a function of the separation, together with the force coefficients spectra and lift cross-correlation functions are presented in the paper.