• Korean Membrane Journal
• /
• v.5 no.1
• /
• pp.68-74
• /
• 2003

Methane steam reforming (MSR) reaction for hydrogen production was studied in a membrane reactor (MR) using two tubular membranes, one Pd-based and one of porous alumina. A higher methane conversion than the thermodynamic equilibrium for a traditional reactor (TR) was achieved using MRs. The experimental temperature range was 350-500$^{\circ}C$; no sweep-gas was employed during reaction tests to avoid its back-permeation through the membrane and the steam/methane molar feed ratio (m) varied in the range 3.5-5.9. The best results (the difference between the MR conversion and the thermodynamic equilibrium was of about 7%) were achieved with the alumina membrane, working with the highest steam/methane ratio and at 450$^{\circ}C$. Silica membranes prepared at KRICT laboratories were characterized with permeation tests on single gases (N$_2$, H$_2$ and CH$_4$). These membranes are suited for H$_2$ separation at high temperature.

• Journal of Korean Society on Water Environment
• /
• v.18 no.4
• /
• pp.387-394
• /
• 2002

The efficiency variation of UF(tubular)/RO(spiral wound) process using acrylic wastewater treated by photo-catalyst pretreatment and coagulant-filter-neutralization pretreatment processes were discussed wit the variation of appled pressure and temperature. Ultrafiltration tubular module using acrylic wastewater treated by photo-catalyst pretreatment and coagulant-filter-neutralization pretreatment processes was shown that COD and T-N were not highly affected with the variation of appled pressure and temperature. It was shown that removal efficiency of COD and T-N was low. Removal efficiency of TDS and turbidity with ultrafiltration tubular module was better with the acrylic wastewater by photo-catalyst pretreatment than acrylic wastewater by coagulant-filter-neutralization pretreatment. T-N and TDS were shown high removal efficiency in reverse osmosis membrane process.

• Membrane Journal
• /
• v.9 no.1
• /
• pp.36-42
• /
• 1999

Permeation behavior of the semiconductor rinsing wastewater contammg Si particles was examined by ultrafiltration using the polyolefin tubular membrane. Flux decline with time was due to the growth of Si cake deposited on the membrane surface and the pore plugging by Si particles. Cake filtration from the cross flow application is compared to the combination of pore blocking and cake filtration from the dead-end application. The cake resistance is 3.16 x $10^{12}$ -4.34 X $\times$$10^{12}$ $m^{-1}$ for the cross flow and 6.6 x $\times$$10^{12}$ -12.19 X $\times$$10^{12}$ $\times$$m^{-1}$for the dead-end flow, respectively. At the initial stage of operation, permeation flux of cross flow type was 1.7 time higher than that of the dead end flow type. Permeation flux of cross flow was about 42 e 1m2 hr and the rejection rate of Si particles was about 96 %. The average particle size of Si particle in the permeate was 20 nm.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1991.04a
• /
• pp.9-9
• /
• 1991

This paper will begin by describing osmosis and how reverse osmosis works. It will show how osmotic pressure affects reverse osmosis operations. It uill explain salt rejection, membrane flux, and recovery rates and the affect that salt built up has on membrane performance. It wil 1 explain the limitations of RO performance and why pretreatment is important. It will describe the two basic types of membrane, asymmetric and thin-film composite and explain the difference between these types plus compare cellulose acetate types to aromatic polyamide type membranes. It will discuss operating efficiences as it compares to feedwater pressure, concentration, temperature and pH. Finally, it will discuss the differences between tubular, plate and frame, hollow fiber and spiral wound element design. It will be a paper that talks about the basics of RO systems and should give a person who is unfamiliar with RO a basic introduction to this type of separation technology.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1994.10a
• /
• pp.58-60
• /
• 1994

막 모듈의 종류에는 평판형(Plate and Frarne), 나권형(Spiral Wound), 중공사형(Hollow Fiber), 관형(Tubular) 등이 있다. 이 중에서 관형 모듈은 공업적 스케일의 한외여과 장치로써 그 특징은 공급액 유로가 일반적으로 커서 전처리를 행하지 않고도 막히는 것이 적으며, 또한 막 표면의 세정이 약품에 의한 것 이외에 스폰지 볼 등에 의한 물리적 세정이 가능한 것이 있으므로 공업용이나 폐액처리 등에 적용할 수 있다는 것이다.

• Membrane and Water Treatment
• /
• v.10 no.5
• /
• pp.353-360
• /
• 2019

ZSM-5 membrane was prepared on tubular macroporous ${\alpha}$-alumina support using a different synthesis route. The effects of organic template agent and Si/Al ratio of the synthesis gel on morphology, structure, and separation performance of the ZSM-5 membrane used for dehydration of isopropanol were investigated. High water perm-selectivity ZSM-5 membrane with a thickness of about $3.0{\mu}m$ and a low Si/Al ratio of 10.1 was successfully prepared from organotemplate-free synthesis gel with a molar composition of $SiO_2$ : $0.050Al_2O_3$ : $0.21Na_2O$ : NaF : $51.6H_2O$ at $175^{\circ}C$ for 24 h. The ZSM-5 membrane exhibited high pervaporation performance with a flux of $3.92kg/(m^2{\cdot}h)$ and corresponding separation factor of higher than 10,000 for dehydration of 90 wt.% isopropanol/water mixture at $75^{\circ}C$.

• Korean Membrane Journal
• /
• v.8 no.1
• /
• pp.13-20
• /
• 2006

The production of CO-free hydrogen streams for feeding PEM-Fuel Cells using catalytic zeolite membrane reactors was analysed by means of selective oxidation. Tubular FAU (Na-Y) zeolite membranes, prepared by a secondary growth method and Pt-loaded, were used in a flow-through MR configuration. The catalytic tests were carried out at $200^{\circ}C$ and at different pressures with a simulated dry reformate shifted gas mixture ($H_2$ ca. 60%, CO 1 %, plus $O_2,\;N_2,\;CO_2$). The operative $O_2/CO$ stoichiometric equivalent feed ratio was ${\lambda}= 2$. These catalytic tests, reducing the CO concentration down to $10{\sim}50$ ppm, verified the possibility of MR integration after using a low temperature water-gas shift unit of a fuel processor to convert hydrocarbons into hydrogen-rich gas.

• The Korean Journal of Physiology and Pharmacology
• /
• v.3 no.5
• /
• pp.513-519
• /
• 1999

Direct exposure of renal tubular brush-border membranes (BBM) to free cadmium (Cd) causes a reduction in phosphate (Pi) transport capacity. Biochemical mechanism of this reduction was investigated in the present study. Renal proximal tubular brush-border membrane vesicles (BBMV) were isolated from rabbit kidney outer cortex by Mg precipitation method. Vesicles were exposed to $50{\sim}200\;{\mu}M\;CdCl_2$ for 30 min, then the phosphate transporter activity was determined. The range of Cd concentration employed in this study was comparable to that of the unbound Cd documented in renal cortical tissues of Cd-exposed animals at the time of onset of renal dysfunction. The rate of sodium-dependent phosphate transport $(Na^+-Pi\;cotransport)$ by BBMV was determined by $^{32}P-Iabeled$ inorganic phosphate uptake, and the number of $Na^+-Pi$ cotransporters in the BBM was assessed by Pi-protectable $^{14}C-labeled$ phosphonoformic acid $([^{14}C]PFA)$ binding. The exposure of BBMV to Cd decreased the $Na^+-Pi$ cotransport activity in proportion to the Cd concentration in the preincubation medium, but it showed no apparent effect on the Pi-protectable PFA binding. These results indicate that an interaction of renal BBM with free Cd induces a reduction in $Na^+-Pi$ cotransport activity without altering the carrier density in the membrane. This, in turn, suggest that the suppression of phosphate transport capacity $(V_{max})$ observed in Cd-treated renal BBM is due to a reduction in $Na^+-Pi$ translocation by existing carriers, possibly by Cd-induced fall in membrane fluidity.

• Journal of the Korean Chemical Society
• /
• v.35 no.1
• /
• pp.51-58
• /
• 1991

A new tubular poly(vinyl chloride) membrane type of nitrate selective electrode was prepared and its characteristics were evaluated. The response slope, detection limit, and response time (t$_{99}$) under the optimum membrane composition (5${\%}$ aliquat-NO$_3$ solution + 32${\%}$ poly(vinyl chloride) + 63${\%}$ dibutyl sebecate) of the electrode were 58.5 ${\pm}$ 0.1 mV/decade, 2.0 ${\times}$ 10$^{-5}$ M, and 25 seconds, respectively. The nitrite ion was determined by the continuous-automated method using the new electrode. 10$^{-2}$ M phosphate buffer solution (pH 7.6) was used as a recipient solution. And also hydrogen peroxide (0.3${\%}$) was added to the recipient as an oxidant. The linear response range and response range and response slope for the standard nitrite solution under the optimum condition of this electrode system were 8.0 ${\times}$ 10$^{-5}$ M ∼ 5.0 ${\times}$ 10$^{-2}$ M and 56.8 ${\pm}$ 0.2 mV/decade, respectively.

• Journal of Korean Society on Water Environment
• /
• v.18 no.2
• /
• pp.113-122
• /
• 2002

A bench-scale anoxic membrane bioreactor (MBR) system, consisting of a bioreactor coupled to a ceramic crossflow ultrafiltration module, was evaluated to treat a synthetic wastewater containing alkaline hydrolysis byproducts (hydrolysates) of RDX, The wastewater was formulated the same as RDX hydrolysates, and consisted of acetate, formate, formaldehyde as carbon sources and nitrite, nitrate as electron accepters. The MBR system removed 80 to 90% of these carbon sources, and approximately 90% of the stoichiometric amount of nitrate, 60% of nitrite. The reactor was also operated over a range of transmembrane pressures, temperatures, suspended solids concentration, and organic loading rate in order to maximize treatment efficiency and permeate flux. Increasing transmembrane pressure and temperature did not improve membrane flux significantly. Increasing biomass concentration in the bioreactor decreased the permeate flux significantly. The maximum volumetric organic loading rate was $0.72kg\;COD/m^3/day$, and the maximum F/M ratio was 0.50 kg N/kg MLSS/day and 1.82 kg COD/kg MLSS/day. Membrane permeate was clear and essentially free of bacteria, as indicated by heterotrophic plate count. Permeate flux ranged between 0.15 and $2.0m^3/m^2/day$ and was maintained by routine backwashing every 3 to 4 day. Backwashing with 2% NaOCl solution every fourth or fifth backwashing cycle was able to restore membrane flux to its original value.