• Journal of Biomedical Engineering Research
• /
• v.27 no.3
• /
• pp.83-88
• /
• 2006

A new method of measuring pulse arrival time (PAT), which is usually used for the estimation of systolic blood pressure, in an unconstrained manner using a chair, is proposed. The capacitive-coupled ECG (CC-ECG) measurement system and the air cushion with balancing tubes system were used for unconstrained PAT measurement. Firstly, the correlation between the standard PAT (S-PAT) from the photoplethysmography (PPG) and the PAT measured in an unconstrained manner (U-PAT) was evaluated. It was observed that U-PAT, which is the time delay from the R-peak of ECG to the steepest decent point of air cushion pressure wave, is significantly correlated with the S-PAT. Secondly, systolic blood pressure (SBP) measured by the radial tonometer is compared to the U-PAT. The ten-beat averaged U-PAT removed respiration effects and demonstrated a high intra-subject correlation with SBP in all participants. Finally, the tonometry SBP was estimated from these U-PAT values for one participant intermittently during half a day.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.119-119
• /
• 2016

Over the last years the anodic formation of ordered $TiO_2$ nanotube layers has created significant scientific interest. Titanium oxide nanotube formation on the titanium or titanium alloy surface is expected to be important to improve cell adhesion and proliferation under clinical conditions. It should be possible to control the nanotube size and morphology for biomedical implant use by controlling the applied voltage, alloying element, current density, anodization time, and electrolyte. $TiO_2$ nanotubes show excellent biocompatibility, and the open volume in the tubes may be exploited as a drug release platform and so on. Therefore, in this study, Nanotube shape on the Ti-29Nb-xHf alloys with applied potentials was reserched. $TiO_2$ nanotube formation on Ti-29Nb-xHf alloys was carried out using anodization technique as a function of applied DC potential (10 V to 30 V and 30 V to 10 V) and anodization time for 60~120 min in $1MH_3PO_4$ with small additions of (0.8 wt. %, to 1.2 wt. %) NaF. The morphology change of anodized Ti-29Nb-xHf alloys was determined by FE-SEM, XRD, and EDS.

• Restorative Dentistry and Endodontics
• /
• v.16 no.1
• /
• pp.190-199
• /
• 1991

The purpose of this study was to evaluate the antimicrobial effect of root canal cements such as AH-26, Sealapex, Canals and Apatite root sealers(Type I, II, III) and to determine the efficacy of their activities. S.mutans(AHT), S.sanguis(NCTC 9811) and B.gingivalis(381) were streaked on blood agar and the PVC tybes filled with root canal cements were applied on. Then the microorganisms were cultured for 48 hours, anaerobically. B.cereus(KCTC 1012) was streaked on nutrient agar, PVC tubes were applied on and were cultured for 48 hours, aerobically. The inhibition zones of root canal cements were measured with vernier caliper. The data statistically analyzed, and the results were as followed. 1. Apatite root sealers(Type I, II, III) showed no inhibition zones. 2. AH-26, Sealapex and Canals had inhibition zones with varying degrees. The inhibition zone of AH-26 was greatest and followed by Canals and Sealapex(P<0.01). 3. As time goes by after mixing the root canal cements, AH-26, Canals and Sealapex showed significantly reducing inhibition zones(P<0.01). 4. There were the least inhibition zones of all the root canal cements on S.mutans and followed in such order as; B.gingivalis, S.sanguis and B.cereus(P<0.01).

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.4
• /
• pp.447-452
• /
• 1999

This paper describes the cycle performance of heat-pump system using R-22 and R-290. Experiments were performed in the smooth tube with inside diameter of 10.07mm and outside diameter of 12.07 mm and grooved inner tube having 75 fins with a height of 0.25mm Condensing temperatures were held constantly between 318K and 328 K while evaporating temperatures were varied from 257 K to 288 K mass velocities from 51 to $280 kg/m^2s$. From the experiments it was known that the evaporating temperature and condensing temperature had more affected by the compressor shaft power than the tube geometries. Cooling capacity of the R-22 and R-290 had similar values in the smooth and grooved inner tubes. The coefficient of performance(COP) was calculated using the compressor shaft power volumetric refrigeration capacity compression ratio and cooling capacity. The COP of the R-290 had slightly higher values than that of R-22 The major parameters affecting the heat pump cycle performance wee the refrigerant proper-ties and operating conditions rather than the geometric shapes of the heat exchanger

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.5
• /
• pp.687-694
• /
• 1999

This study was conducted to develop new drying process for automatic control and marine engi-neering system. Air-water tests were carried out to investigate dryer performance. The dispersed flow in he dryer test apparatuses was also simulated by using a numerical code which solves the Dittus-Boelter equation for continuous liquid phase and the Reynolds equation of droplet motion for continuous liquid phase and the Reynolds equation of droplet motion for dispersed phase to predict droplet removal efficiency. Proper conditions for dehumidification were optimized by response ambient conditions. When the selected indexes were constrained in the range of 85-98% moisture content above $15^{\circ}$ and more than mass flow rates of moist air 750kg/h. The numerical results were compared with the experimental data pertaining to the removal effi-ciency at chamber stage and overall pressure drop along concentric tubes Good agreement was obtained as for the efficiency while relatively poor agreement was obtained for the relative humidity. The results also showed that the efficiency depended strongly on the relative humidity at the inlet condition which indicated the importance of estimating the heat exchanger length. Effects of some design parameters in both removal efficiency and breakthrough onset condition are discussed.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.4
• /
• pp.561-571
• /
• 1997

In this paper, the fundamental equations are developed for the pulsatile laminar flow generated by changing the oscillatory flow with $0{\leq}f{\leq}48Hz$ into a steady one with $0{\leq}Re{\leq}2500$ in a rigid circular pipe. Analytical solutions for the wave propagation factor k, the axial distributions of cross-sectional mean velocity $u_m$ and pressure p are schematically derived and confirmed experimentally. The axial distributions of centerline velocity and pressure were measured by using Pitot-static tubes and strain gauge type pressure transducers, respectively. The cross-sectional mean velocity was calculated from the centerline velocity by applying the parabolic distribution of the laminar flow and it was confirmed by using the ultrasonic flowmeter. It was found that the axial distributions of cross-sectional mean velocity and pressure agree well with theoretical ones and depend only on the Reynolds number Re and angular velocity $\omega$.

• Journal of the Korea Society for Simulation
• /
• v.14 no.2
• /
• pp.35-43
• /
• 2005

Feedwater heaters of many nuclear power plants have recently experienced wall thinning damage, which will increase as operating time progresses. As it is judged that the wall thinning damages have generated due to local fluid behavior around the impingement baffle installed in downstream of the high pressure turbine extraction steam line to avoid colliding directly with the tubes, numerical analyses using PHOENICS code were performed for two models with original clogged impingement baffle and modified multi-hole impingement baffle. To identify the relation between wall thinning and fluid behavior, the local velocity components in x-, y-, and z-directions based on the numerical analysis for the model with the clogged impingement baffle were compared with the wall thickness data by ultrasonic test. From the comparison of the numerical analysis results and the wall thickness data, the local velocity component only in the y-direction, and not in the x- and z-direction, was analogous to the wall thinning configuration. From the result of the numerical analysis for the modified impingement baffle to mitigate the shell wall thinning, it was identified that the shell wall thinning may be controlled by the reduction of the local velocity in the y-direction.

• Korean Journal of Plant Taxonomy
• /
• v.46 no.1
• /
• pp.55-59
• /
• 2016

Justicia kampotiana Benoist (Acanthaceae) is reported as a new record for the flora of Vietnam. This species differs from its allied species J. ingrata Benoist in having corolla outside pubescent, tubes slightly longer than limbs and considerably shorter petioles. Description, line drawing and color photographs are provided for species identification. Furthermore, a comparison of the diagnostic characters with those of related species is made.

• Korean Journal of Computational Design and Engineering
• /
• v.19 no.1
• /
• pp.19-28
• /
• 2014

The filament winding method is widely used to manufacture products of fiber reinforced plastics (FRP), such as high pressure vessels, launch tubes and pipes. For reducing winding time, the method of winding by filament band which consists of several filament fibers is used. NC winding machine is used for precise winding and NC path is needed. Before filament winding, users should verify that winding path which presented by a line is appropriate by filament winding simulation. Also, the used length of each filament is different. So, if the peak filament exhausted, it causes to stop manufacturing. In this research, we developed software which visualizes 3D graphic of filament band winding path and simulates winding process on real time. And we proposed algorithm about calculation of each filament usage. We use geodesic equation for generating filament band surface and calculating the usage length of each filament.

• Journal of the Korean Chemical Society
• /
• v.43 no.4
• /
• pp.401-406
• /
• 1999

Trace amount of cadmium was quantitatively extracted with 1% Aliquat 336-MIBK from 0.2M KSCN and 0.01M-HCl. Test tubes with a screw cap stopper were used for extraction in place of conventional separating funnels and organic solvents used were less dense than water. In this analysis, 22 times concentration effect was achieved with higher selectivity without interference. The detection limit of cadmium was 0.7ppb, therefore trace cadmium was easily analyzed by this method. The proposed method was applied to the determination of cadmium in blood serum and extraction mechanism was elucidated.