• 대한기계학회논문집B
• /
• 제27권3호
• /
• pp.347-356
• /
• 2003

The characteristics of near wakes of circular cylinders with serrated fins are investigated experimentally using a hot-wire anemometer for various freestream velocities. Near wake structures of the fin tubes are observed using a phase average technique. With increasing fin height and decreasing fin pitch. oscillation of streamwise velocity increases. It file oscillation of lateral velocity decreases. The time averaged V-component velocity distribution of the finned tube is contrary to that of the circular cylinder due to the different strength of entrainment flow. This strength is affected by the distance of (equation omitted) = 1.0 contour lines. (equation omitted) = 1.0 contour line approaches to the wake center line when the fin density is increased. When the distance between (equation omitted) = 1.0 contour lines comes close the shear force should be increased and the flow toward the wake center line can be more strengthened because of the shear force. Factors related to the velocity recovery in the near wake of the finned tube are attributed to tile turbulent intensity, the boundary layer thickness. the position and strength of entrainment process.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.609-614
• /
• 2008

The heating and cooling performance of system multi-air conditioner under high-head and long-line conditions are experimentally investigated. The maximum head and tube length were 110 m and 1000 m, respectively. The experimental system was composed of 4 outdoor units with module systems, and 13 indoor units which were joined with the mode change unit by single-tube circuit. Field tests without indoor and outdoor temperature control were performed in a general office building with 22 different working conditions. Experimental results were prepared on the p-h diagram. Also the oil level in the compressor was normally maintained at the safety zone for the system multi-air conditioner with high-head and long-line conditions.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 동계학술발표대회 논문집
• /
• pp.304-309
• /
• 2008

The heating and cooling performances of system multi-air conditioner for various refrigerant flow rates with high-head and long-line conditions are experimentally investigated. The maximum head and tube length were 110 m and 1000 m, and the two different adjustments of refrigerant flow rates were +20 % and -20 %, respectively. The experimental system was composed of 4 outdoor units with module systems, and 13 indoor units which were joined with the mode change unit by single-tube circuit. Field tests without indoor and outdoor temperature control were performed in a general office building with two different refrigerant flow rates. Especially, the oil level in the compressor was normally maintained at the safety zone. Experimental results were prepared on the p-h diagram.

• 한국정밀공학회지
• /
• 제18권7호
• /
• pp.179-185
• /
• 2001

Porthole die extrusion is profitable to manufacture long tube with hollow section. The material through portholes is gathered within chamber and welded under high pressure. This weldability which classifies the quality of tube product is affected by several variables and die shape. But, porthole die extrusion has been executed on the experience of experts due to the complicated die assembly and complexity of metal flow. Analytic approaches that are useful in profitable die design and in the improvement of productivity are inevitably demanded. Therefore, the objective of this study is respectively to analyze the behavior of metal flow and to determine welding pressure of hot extrusion product according to the various billet temperature, bearing length and tube thickness by FE analysis and its results are compared with tube expanding tests.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권2호
• /
• pp.136-142
• /
• 2015

The shell and tube heat exchanger is an essential part of a power plant for recovering transfer heat between the feed water of a boiler and the wasted heat. The baffles are also an important element inside the heat exchanger. Internal materials influence the flow pattern in the bed. The influence of baffles in the velocity profiles was observed using a three-dimensional PIV (Particle Image Velocimetry) around baffles in a horizontal circular tube. The velocity of the particles was measured before the baffle and between them in the test tube. Results show that the velocity vectors near the front baffle flow along the vertical wall, and then concentrate on the upper opening of the front baffle. The velocity profiles circulate in the front and rear baffle. These profiles are related to the Reynolds number (Re) or the flow intensity. Velocity profiles at lower Re number showed complicated mixing to obtain the velocities and concentrate on the lower opening of the rear baffle as front wall. Numerical simulations were performed to investigate the effects of the baffle and obtain the velocity profiles between the two baffles. In this study, a commercial CFD package, Fluent 6.3.21 with the turbulent flow modeling, k-${\epsilon}$ are adopted. The path line and local axial velocities are calculated between two baffles using this program.

• 수산해양교육연구
• /
• 제28권3호
• /
• pp.645-652
• /
• 2016

At the initial stage of propulsion shaft design, in line with shaft alignment, an intensified consideration of lateral vibration is needed to verify its operational safety. Recently the alignment problem affecting the lateral vibration has been becoming issues. However, the theoretical method of forced lateral vibration analysis is not cleary established so far and it is about to simply limited among the classification societies and international standards to avoid the blade natural frequency resonance cpm outside of ${\pm}20%$ of engine rpm at MCR. On the other hand, longer center distance between each support bearing shows an affirmative result normally in shaft alignment analysis whereas the blade order resonance speed may cause lowering near the limitation in the aspect of lateral vibration. Therefore, it is required careful attention to engineers as described above. As a method to solve the problem, it is mainly considered that remove forward stern tube bearing. In this paper, based on a medium size container ship case, theoretical study was carried out in the context of the forward stern tube bearing. The various effects and functions of forward stern tube bearing are reviewed and evaluated. Then an guidance note to lead the conclusion is proposed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.296-301
• /
• 2003

A study on the engineering design and numerical thermo-hydraulic analysis for KSTAR TF coil structure cooling system has been conducted. The numerical analyses have been done to verify the engineering design of cooling using the commercial code, FLUENT and in-house code for calculating helium properties which varies with cooling tube's heat transfer. Through the engineering design process based on the steady heat balance concepts, the circular stainless steel tube with inner diameter of 4 mm for TF coil has been selected as cooling tube. From normal operation mode analysis results, total 28 cooling tubes were finally chosen. Also, three dimensional cool down analysis for TF coil with designed cooling tube was satisfied with next three design criteria. First is cooling work termination within a month, second is maximum temperature difference within 50 K in TF coil structure and third is exit helium pressure above 2 bar. Consequently, these cool down scenario results can afford to adopt as operating scenario data when KSTAR facilities operate.

• 설비공학논문집
• /
• 제7권3호
• /
• pp.366-381
• /
• 1995

A performance analysis of refrigeration system using the HFC-134a and scroll compressor is performed numerically. The refrigeration system mainly consists of various standard components such as heat exchanger, compressor, and expansion device. The model for heat exchanger performance is based on a tube-by-tube method which is analyzed separately by considering the cross-flow heat transfer with the outdoor air flow and pressure drop. Compressor is used the scroll-type compressor which has many merits such as high efficiency, low noise and vibration, and small in size. Short-tube is included as an expansion device. Vapour and liquid line are also considered for the performance analysis of refrigeration system. Using the modeling of various components of refrigeration system, a performance comparison of CFC-12 and HFC-134a is performed numerically for the various outdoor air temperature and various values of short-tube diameter. As the results of this study, the refrigeration system performance decreases as the outdoor air temperature increases. And the optimum short-tube diameter based on COP is 1.37mm for this system.

• 한국광학회지
• /
• 제17권1호
• /
• pp.60-67
• /
• 2006

본 논문에서는 I자형과 U자형의 변압기를 각각 사용한 펄스형 고전압 전원에 의해 대기압에서 동작되는 파장 337.1 nm인 질소레이 저의 방전간극과 레이저 관에 각각 광섬유를 설치하고, 이를 통해 나오는 빛을 핀 다이오드를 이용하여 선전리 현상을 직접 관측하고 출력특성을 조사하였다. 레이저 출력이 안정되고 높아질수록 선전리 현상을 뚜렷이 관측할 수 있었고, 레이저 출력은 I자형 변압기보다는 U자형의 변압기를 사용하였을 때 높은 출력과 안정성을 얻었으며, 또한 펄스 방전의 예비동작 시간도 U자형이 1/3 정도 짧았다. U자형의 변압기를 사용하고 출력창의 반사율 $40\%$, 반복율 10 Hz, 레이저 관내에서 질소기체의 유동률이 4 ${\iota}$/min, 방전간극 내에서 질소기체의 유동율이 1500 cc/min, 방전간극 전극 거리 3.0 mm, 레이저 관 내 전극거리 5.0 mm 일 때, 안정성이 $2.7\%$인 $36{\mu}J$의 출력을 얻었다.

• 산업공학
• /
• 제6권1호
• /
• pp.99-112
• /
• 1993

This study deals with analysis of material from in Tube manufacturing line. This line is a multi product flow ship type production line, which consists of 5 steps of work station. Some work stations involve in unnecessary moving activities of workers and much work in-process storage due to the non-systematic material flow with respect to the different lot size production of multi-items. To improve productivity for this line, one alternative is considered such as grouping two work stations by using GT and JIT concepts. Also, feasibility analysis for this alternative is performed using and simulation model built by SIMAN IV simulation language.