• 한국생산제조학회지
• /
• 제9권3호
• /
• pp.160-168
• /
• 2000

Hydroforming is a metal forming process that enables circular metal tubes to be formed in to the parts with the complex cross section along the curved axial direction. Recently this hydroforming process is largely used for the production of the automotive parts. This paper presents the results of tube bending and hydroforming simulations in cases of the varying weld line positions of the tube. Ten cases of prebending and hydroforming simulations are carried out to find the optiaml weld line position.

• 한국진공학회지
• /
• 제17권3호
• /
• pp.247-252
• /
• 2008

휴대용 XRF(X-Ray Fluorescence) 장치에 적용하기 위하여 개발한 투과 양극형 x-ray tube를 이용하여 XRF 실험을 하고, x-ray tube가 XRF data에 미치는 영향을 조사하였다. W-target tube와 Rh-target tube를 이용하여 측정한 XRF data는 알려진 결과와 잘 일치하였다. 35 kV와 관전압과 $40{\mu}A$의 관전류에서 W-target tube로 측정한 Fe $K_{\alpha}$-line의 FWHM은 약 180 eV로써, 이 값은 물질의 성분분석을 하기에 충분한 것으로 확인하였다. XRF data와 x-ray tube의 적분강도 곡선을 비교 분석해 본 결과, 휴대용 XRF 장치에는 W-Target tube보다는 Rh-Target tube를 사용하는 것이 더 유리함을 밝혀내었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.227-230
• /
• 2009

The aim of this study was to improve extrudability limit, eliminate welding line and obtain optimum thixoextrusion conditions for manufacturing tubes of 7075 Al wrought alloy. By thixoextrusion, it was possible to improve deformability, control isotropy with extrusion direction, eliminate welding line (seamless) and save cost due to low energy consumption compared with conventional extrusion processes. The welded part was not observed at the welding line area. The grains of thixoextruded tube were homogeneously distributed and equiaxed grains were observed. Therefore, thixoextrusion is the most effective variable for the control of the magnitude of the welding line.

• 대한기계학회논문집
• /
• 제13권5호
• /
• pp.1023-1031
• /
• 1989

본 연구에서는 격자관군(in-line tube banks)과 엇갈림관군(staggered tube banks)에서의 유동특성을 해명하기 위한 기초로서, 일렬관군에 대해 유동특성을 통계적으로 조사한다. 이를 위해, 먼저 유동의 가시화와 관의 표면압력 측정실험이 행해진다. 또한, 통계적 기법의 도입을 통하여 관 주위의 평균속도, 난류강도, 파워 스펙트럼 밀도함수, 스트로홀수(strouhal number), 자기상관계수, 활률 밀도함수 등의 측정이 수행된다.

• Nuclear Engineering and Technology
• /
• 제53권3호
• /
• pp.1029-1040
• /
• 2021

For the structural integrity evaluation of pressurized water reactor (PWR) steam generator (SG) tubes subjected to transient hydraulic loading, determination of the tube-to-tube gap velocity and static pressure distributions along the tubes is prerequisite. This paper addresses both computational fluid dynamics (CFD) and analytical approaches for predicting the tube-to-tube gap velocity and static pressure distributions during blowdown following a feedwater line break (FWLB) accident at a PWR SG. First of all, a comparative study on CFD calculations of the transient velocity and pressure distributions in the SG secondary sides for two different models having 30 or no tubes is performed. The result shows that the velocities of sub-cooled water flowing between any adjacent two tubes of a tubed SG model during blowdown can be roughly estimated by applying the specified SG secondary side porosity to those of the no-tubed SG model. Secondly, simplified analytical approximate solutions for the steady two-dimensional SG secondary flow velocity and pressure distributions under a given discharge flowrate are derived using a line sink model. The simplified analytical solutions are validated by comparing them to the CFD calculations.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.255-262
• /
• 2008

The simulation of refrigeration cycle is important since the experimental approach is too costly and time-consuming. The present simulation focuses on the effect of capillary tube-suction line heat exchangers (CT-SLHX), which are widely used in small vapor compression refrigeration systems. The simulation of steady states is based on fundamental conservation equations of mass and energy. These equations are solved simultaneously through iterative process. The non-adiabatic capillary tube model is based on homogeneous two-phase model. This model is used to understand the refrigerant flow behavior inside the non-adiabatic capillary tubes. The simulation results show that both of the location and length of heat exchange section influence the coefficient of performance (COP). These results can be used in either design calculation of capillary tube length for refrigeration cycle or effect of suction line heat exchanging on refrigeration cycle.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.1992-1996
• /
• 2007

This study focuses on the hydrogen embrittlement of iron tube for fuel line of PEMFC (Proton Exchange Membrane Fuel Cell). PEMFC is operated by feed of hydrogen as a reactant and steam for proton conductivity of membrane. However, the environment with hydrogen and steam occur the hydrogen-induced degradation in BOP system. When iron tube was exposed to hydrogen and steam condition for 24 hours, the oxide layer on the surface was decreased by reduction. When the ambient temperature was 90$^{\circ}C$ micro cracks were found on the surface than any other temperature. The mechanical strength of iron tube was 3% lower than that of non-experiment tube. Maximum tensile stress was decreased 8%.

• 비파괴검사학회지
• /
• 제24권4호
• /
• pp.331-340
• /
• 2004

기기 건전성의 온라인 검사 및 감시 기술은 기존의 원전의 가동 중 검사의 효율적 수행에 필요한 정보를 제공한다. 유도 초음파는 온라인 검사와 감시에 활용 가능성이 있는 기술 중의 하나로 알려져 있다. 본 연구에서는 온라인 검사 겐 감시 기술 개발의 일환으로 유도초음파를 이용하여 파이프의 건전성을 검사/감시하는 기술을 개발하고자 한다. 이를 위해 증기 발생기 세관을 실험 대상으로 하여 분산 선도 덴 특정 모드에 대응하는 초음파 입사각을 계산하였다. Short time Fourier transform을 이용한 시긴-주파수 분석을 통하여 유도초음파 모드를 확인하였으며, 유도 초음파가 증기발생기 세관의 곡관 부분을 통과할 때 모드 변환이 발생하지 않는 것을 실험적으로 확인하였다. 유도 초음파를 이용한 증기발생기 세관의 최적 검사 모드를 제안하고 실험에 의하여 이를 확인하였다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 1990년도 추계학술발표회논문집
• /
• pp.35-40
• /
• 1990

Temperature distribution of high pressure mercury lamp has been mesured as a function of time using spectroscopic method. Sampling signal which is synchronized by lamp voltage was used to mesure temporal line intensity at each radius. To obtain radial temprature distribution, the mesured intensity was transformed into radial line intensity by Abel's formula. Absolute temperature profile was calculater from relative intensities of spectral lines as a function of line and tube radius. The temperature profile is very similar to the electrical tube current profile.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제41권2호
• /
• pp.66-73
• /
• 2015

Objectives: To assess the validity of the vertical tube-shift method using intraoral periapical radiography (IOPAR) for determining the relationship between the mandibular third molar roots and the inferior alveolar nerve (IAN) canal in comparison with cone-beam computed tomography (CBCT). Materials and Methods: Fifty impacted mandibular third molars were analyzed using the IOPAR vertical tube-shift method and CBCT. The relationship of the IAN canal to the impacted mandibular third molar was recorded as buccal, lingual or in line with the apex and was compared with CBCT findings. The sensitivity, specificity, positive predictive value (PPV), and negative predictive value (NPV) of the vertical tube-shift method in depicting the relationship (buccal/lingual/in line with the apex) of the IAN canal to the third molar root apex was calculated. Results: The sensitivity and specificity PPV and NPV of the IOPAR vertical tube-shift technique was found to be highest for a lingual relationship (100%) followed by buccal (94.4%, 92.3%, 97.1%, and 85.7%) and in line with the apex relationship (88.9%, 95.0%, 80.0%, and 97.4%) of the IAN canal with the third molar root apex, respectively. A statistically significant association was observed between the IOPAR vertical tube-shift method and the CBCT with a P-value <0.01. Conclusion: The vertical tube-shift method can be used as an effective diagnostic tool in assessing the relationship of the IAN canal to the third molar root apex with high sensitivity, specificity, PPV, and NPV.