• Tribology and Lubricants
• /
• 제18권4호
• /
• pp.305-311
• /
• 2002

Three different kinds of brake discs including two coated brake discs and one steel disc were tested under the same experimental conditions on a reduced scale braking test bench. A braking test bench was specially designed to analyse thermo-mechanical and frictional behaviors of two types of brake with different sizes in stop and hold braking modes. Plasma spray coating technique was also used to coat the discs with ceramic powder. During the test four commercial brake pads were coupled with discs. Ceramic coated discs showed good stability in friction coefficient at high speed and high energy braking conditions. But they caused large wear loss of pad mass compared with the steel disc. It was shown that thermal barrier effect in ceramic coated discs adjusted the thermal partition between pad and disc. For a steel disc. it showed fluctuating friction coefficient at high speed but small wear loss of pad mass compared with ceramic coated discs.

• Tribology and Lubricants
• /
• 제18권4호
• /
• pp.273-278
• /
• 2002

Grease deterioration of mineral oil type grease was investigated using sealed deep groove ball bearings (6203) and bearing life test rig. The bearing test was performed under 3,000 rpm and 245 N radial load at 120。C. Grease taken ken tested bearings was checked in using certain evaluation methods, for example, oxidation induction time (OIT), FT-IR peak intensity, leakage .ate, bleeding .ate, total acid number. (TAN) and bearing noise increase. Within these test conditions, OIT, TAN, bleeding rate were changed gradually in accordance with bearing operating time and showed useful indices for deterioration of grease.

• Tribology and Lubricants
• /
• 제15권3호
• /
• pp.265-271
• /
• 1999

Wherever there are rotating equipment and contact between surface, there is wear and the generation of wear particles. The particles contained in the lubricating oil carry detailed and important information about the condition monitoring of the machine. This information may be deduced from particle shape, composition, size distribution, and concentration. Therefore, This paper was undertaken to Ferrography system of wear debris generated from lubricated moving machine surface. The lubricating wear test was performed under different experimental conditions using the Falex wear test of Pin and V-Block type by Ti(C, N) coated. It was shown from the test results that wear particle concentration (WPC) and wear severity Index( $I_{S}$), size distribution in normal and abnormal wear have come out all the higher value by increases sliding friction time. Wear shape is observed on the Ferrogram it was discovered a thin leaf wear debris as well as ball and plate type wear particles. This kind of large wear shape have an important effect not only metals damage, but also seizure phenomenon.

• Tribology and Lubricants
• /
• 제14권4호
• /
• pp.108-113
• /
• 1998

In order to investigate the characteristics of top ring groove deposit formation in diesel engine, engine test and simulation test were performed. From component analysis of used oils sampled from actual running engines, soot content in engine oil was selected as a main parameter for evaluating oil degradation. Deposit formation is highly related to soot content in lubricating oils. And high soot content oil accelerates deposit formation even in low temperature region below 26$0^{\circ}C$. In low temperature region below 26$0^{\circ}C$, deposit formation rate is mainly affected by top ring groove temperature. However, in high temperature region above 26$0^{\circ}C$, deposit formation rate is affected by soot content as well as top ring groove temperature. Therefore, soot content as well as top ring groove temperature should be kept a certain level in order to prevent troubles due to carbon deposit formation.

• Tribology and Lubricants
• /
• 제18권3호
• /
• pp.187-193
• /
• 2002

The half-value breadth off-ray diffraction profile line is generally used for a factor in nondestructive hardness measuring method of steel. In this paper, the problem in using the half-value breadth for the hardness measuring method is evaluated in strain hardened steel. And new hardness measuring method using residual stress is proposed X-ray diffraction test after rolling contact fatigue test of ball bearing with inner race of various hardness are carried out to measure the distribution of residual stress and half-value breadth from surface. The result of this study shows that there is little correlation between half-value breadth and hardness in the higher strength region and in the region increasing the hardness by strain hardening. But the magnitude of residual stress on/under race after rolling contact fatigue test becomes clearly to be correlative with hardness. Thus, it is concluded that the hardness of strain hardened steel can be estimated by this relationship between residual stress and hardness.

• Tribology and Lubricants
• /
• 제11권1호
• /
• pp.27-36
• /
• 1995

Maximum allowable PV values of oilless composite bearing materials (70% epoxy-resin/30% Graphite) were measured and compared at various types of test rigs that have different contact geometry and the operating conditions. Test results showed that material failure was mainly characterized by the sharp increase in both coefficient of friction and surface temperature, and different PV values were measured under different Contact geometry. The discrepancy in measurement of PV values was analyzed in the light of theoretical frictional heating analysis. Results show that surface temperature rise depends on its contact geometry, and PV values could be overestimated in the testing conditions of high sliding velocity. Test data of different contact geometry were normalized by using a normalized contact pressure and sliding velocity; it showed a good correlation. This work suggests that normalized PV values could be more effective in evaluating bearing materials than conventional PV values for a design parameter of journal bearings.

• Tribology and Lubricants
• /
• 제12권3호
• /
• pp.92-99
• /
• 1996

Energy-efficient contrarotating propeller systems have been recently reviewed as one of alternative means in marine car-carrier applications. Contrarotating rotors preclude the usage of conventional plain journal bearings due to the lack of load carrying capacity. A new multi-recess hydrostatic contrarotating journal beating test facility has been designed and installed to test the static load carrying capacity. Measurements of flow rates and orbits have been investigated by testings on a overhung-type contrarotating rotor system which is supported by a hydrostatic journal bearing. Numerical results of static equilibria were compared with test results. Various contrarotating speed combinations, and supply pressure conditions were selected. The numerical predictions of orbit centers and flow rates are generally accurate.

• Tribology and Lubricants
• /
• 제12권3호
• /
• pp.72-78
• /
• 1996

This paper was undertaken to analyze the morphology of wear debris generated from lubricated moving machine surfaces by image processing. The lubricati, ng wear test was performed under different experimental conditions using the wear test device made in our laboratory and wear test specimen of the pin on disk type wear rubbed in paraffme series base oil, by varying applied load, sliding distance. The four parameters (50% volumetric diameter, aspect, roundness and reflectivity) to describe the morphology have been developed and outlined in the paper. A system using such techniques promises to obviate the need for subjective, human interpretation of particle morphology in machine condition monitoring, thus to overcome many of the difficulties with current methods and to facilitate wider use of wear particle analysis in machine condition monitoring.

• Tribology and Lubricants
• /
• 제26권6호
• /
• pp.322-328
• /
• 2010

An inter-propellant seal (IPS) for 75 ton class thrust turbopump was tested. Leakage characteristics were presented with a given range of pressure difference under cryogenic as well as room temperature conditions. For cryogenic tests, liquid nitrogen was used as analogic fluid of liquid oxygen (LOX) while water was used instead of kerosene for room temperature condition. Test results showed that IPS had satisfactory leakage performance. Additionally endurance test was conducted to prove the life time of manufactured IPS and the tested IPS had successfully survived during required life time, 2100 seconds.

• Tribology and Lubricants
• /
• 제22권1호
• /
• pp.8-13
• /
• 2006

Sliding wear tests have been performed to evaluate the effect of normal load decrease on the wear depth of nuclear fuel rods in room temperature air. The objectives of this study are to quantitatively evaluate the supporting ability of spacer grid springs, to estimate the wear depth by using the contacting force decrease and to compare the wear behavior with increasing test cycles (up to $10^7$) at each spring condition. The result showed that the contacting load decrease depends on the spring shape and the applied slip amplitude. The estimated wear depth is smaller when compared with measured wear depth. Based on the test results, the wear mechanism, the role of wear debris layer and the spring shape effect were discussed.