• Tribology and Lubricants
• /
• v.21 no.6
• /
• pp.302-305
• /
• 2005

Various carbon nanotubes (CNTs) are added into the epoxy matrix as reinforcements to investigate the effect on the wear behavior. Effects to the tribological properties of different loading concentrations and types of surface modification are investigated by using a linear reciprocal wear tester. As increasing the concentration of CNTs shows the reduction of the wear loss. Moreover, surface modified CNTs give better tribological property than as produced CNTs. It is due that the functional groups on the surface of CNTs increase the interfacial bonding between CNTs and epoxy matrix through chemical bonding. Changes in worn surface morphology are observed by optical microscope and SEM to investigate the wear behavior. CNTs in the epoxy matrix near the surface are exposed and it becomes the lubricating working film on the worn surface. It reduces the friction and results in the lower surface roughness morphology in the epoxy matrix as increasing the contents of the CNTs.

• Tribology and Lubricants
• /
• v.29 no.2
• /
• pp.117-123
• /
• 2013

Dimethyl ether (DME) has a high cetane number that is suitable for diesel fuel. DME does not contain sulfur or nitrogen, and is an oxygenated fuel so it produces no particulate matter when combusted and is environmentally friendly. DME fuel for diesel engines show excellent material properties such as a lower volumetric heating value, lower boiling point, lower lubricity, and stronger solvent effect than light oil. This study experimentally examined a lubricity improver (LI) for dimethyl ether. A diesel LI based on biodiesel and fatty acid methyl ester was tested among DME LI candidates. The long-term storage stability and physical properties of the optimum LI for DME were determined.

• Tribology and Lubricants
• /
• v.10 no.4
• /
• pp.59-68
• /
• 1994

This study is concerned with the change of physical and chemical properties of the used oil in gasoline and LPG engine. The used oils of engine were sampled from dynamometer and cars. The field tests of car were done in city and on highway. The properties of oil were TAN, TBN, visocity, oxidation, ZDTP depletion factor and etc. Also the relation between the chemical change and antiwear property was studied. From the study, it was shown that the decrease of antiwear property of used oil was depended on the changes of ZDTP depletion factor as well as TAN (total acid number). Also, it was found that the oil used by LPG car was deteriorated within the shortest distance among the other gasoline cars. The antiwear property of oil decreased as the running distance increased. The gasoline engine oil drove mainly on highway was the least deteriorate of properities for the same running distance.

• Tribology and Lubricants
• /
• v.15 no.1
• /
• pp.52-58
• /
• 1999

Nano-indentation and nano-scratch tests were peformed to assess the mechanical and tribological properties of the coating on a commercially available thin-film magnetic recording disk. Surface topography and roughness of the disk was studied using atomic force microscopy. The hardness and elastic modulus data show a peak at an indentation depth equivalent to the thickness of carbon overcoat, indicating strong influence of the coatin $g_strate interaction and the coating surface roughness on the measurements. The variations of surface roughness data were analysed statistically based on the normal probability distribution theories and Weibull cumulative probability theories.es.

• Tribology and Lubricants
• /
• v.10 no.3
• /
• pp.39-46
• /
• 1994

In order to investigate the effect of the ceramic reinforcements on the wear properties of aluminum bronze composites, Cu-8wt%Al aluminum bronze alloys reinforced with the Saffil alumina short fiber were produced by the powder metallurgical method and tested by a pin-ondisc wear testing machine. The wear surfaces of the pin specimens and discs, wear debris, and the cross sections of the wear specimens were observed by SEM. The wear mechanism according to various wear conditions and the change of microstructure in the composites were also discussed. In the results, the reinforcement of the composites with alumina short fiber was very effective at the higher applied load over 10N. The material transportation to the counter disc was observed in the alloy specimens without reinforcements. However, the composites reinforced with ceramic particles and fibers showed the resistance against the material transportation.

• Tribology and Lubricants
• /
• v.15 no.1
• /
• pp.59-67
• /
• 1999

Three kinds of reation-bonded SiC that reaction-bonded SiC(RBSC), RBSC reinforced by carbon fiber and RBSC reinforced by activated carbon fiber were prepared for investigating the change of erosion properties. The characteristics of microstructures and the phases have been investigated by using scanning electron microscope and XRD analysis. The hardness test toughness test and erosion test was carried out. In the cases with no carbon fiber, those kind of specimens had the highest value of hardness and the lowest value of toughness. With the increase of carbon fiber content the hardness and the weight loss were decreased, but the toughness was increased in the cases with carbon fiber. In the cases with activated carbon fiber specimens had the highest value of toughness and the lowest value of hardness with 30% contents of activated carbon fiber.

• Tribology and Lubricants
• /
• v.20 no.1
• /
• pp.33-40
• /
• 2004

This study represents the newly advanced formulation of hydraulic fluids for extended drain interval and introduces the performance results of used oil samples from various excavators. The used oil samples, in this paper, show that there is a sharp change in viscosity drop and moderate additive depletion when viscosity index of hydraulic oil is very high. For the extension of hydraulic fluid life, it is necessary to improve the stability of viscosity and oxidation. New target properties from the used oil analysis were proposed for extended life. Performance of newly developed hydraulic oil based on used oil analysis is compared with previously used one. The properties of new formulation are the viscosity index of 140 and improved thermal stability consists of VHVI base oil. Field test results showed the possibility of extension of fluid life. Additionally, for development of high performance product, new required propertied and performances were discussed.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1556-1557
• /
• 2008

"Biomimetics" is the study and simulation of biological systems with desired properties. In recent times, biomimetic surfaces have emerged as novel solutions for tribological applications in micro-electromechanical systems (MEMS). These biomimetic surfaces are attractive for MEMS application as they exhibit low adhesion/friction and wear properties at small-scales. In this paper, we present some of the examples of biomimetic surfaces that have potential application in small-scale devices.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.87-92
• /
• 1995

Lip seals, important components in many hydraulic devices, dissipate energy through friction, resulting in power loss. This study contributes to an understanding of lip seal friction by further exploring the connections between friction behavior, viscoelastic properties of robber and viscous properties of the lubricant. Experiments haven been conducted for short stroke oscillations, where these connections are quite strong. Sliding friction experiments at a variety of pressures, temperatures and oscillation rates (for different seal materials, surface roughnesses and lubricant viscosities) are examined. Speculative explanations are suggested for conditions under which friction maxima and frictional vibrations occur.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.93-98
• /
• 1995

To increase the information storage density in magnetic disk files, the head, the headdisk spacing must be reduced. This has motivated the investigation of alternatives to the conventional air-lubricated head-disk interface (HDI), which operates at a spacing of about 100 nm. One such alternative under consideration is the liquid-lubricated bearing. To properly model the HDI with a liquid bearing it is necessary to incorporate the theological properties of liquid lubricants at high shear rates. These rheological properties themselves are most easily measured within the HDI. Recently, some question has arisen in the literature concerning the interpretation of the frictional data acquired in this manner. In this study analytical and numerical solutions of the Reynolds eqn. are applied to the starved, liquid lubricated HDI to provide some validation of the rheological data reported the author and coworkers (Streator et al., 1994). Results of the analysis highlight the importance of the inlet taper region in determining the equilibrium configuration of the starved HDI even when only a small fraction of its length is wetted by the lubricant.