• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.10a
• /
• pp.86-92
• /
• 1997

When Lubricants is used under severe running condition, tribological characteristics is very important. I have studied the lubricating oil viscosity, kinds of additives and lubricating oil temperatures were changed. In order to study the effect of oil temperature on the wear of the surface, the temperature of the oil was changed for the same sample. Moreover, the temperatures of three kinds of oils which have very different viscosities at room temperature, were varied while the oil viscosity was unchanged. It was shown from the test results that wear is not greatly affected by the amount of ZnDTP antiwear agent, but E-P additives are less effective against wear than ZnDTP additives. The viscosity of lubricating oil and its tempea-ature greatly affect the wear of the surface. Combining all the wear data with those of the surface strength, it was observed that the higher the load, the lower the scratch of wear, and also in the case of the same running load, the lower the wear, the longer the life of the surface strength.

• Tribology and Lubricants
• /
• v.20 no.1
• /
• pp.33-40
• /
• 2004

This study represents the newly advanced formulation of hydraulic fluids for extended drain interval and introduces the performance results of used oil samples from various excavators. The used oil samples, in this paper, show that there is a sharp change in viscosity drop and moderate additive depletion when viscosity index of hydraulic oil is very high. For the extension of hydraulic fluid life, it is necessary to improve the stability of viscosity and oxidation. New target properties from the used oil analysis were proposed for extended life. Performance of newly developed hydraulic oil based on used oil analysis is compared with previously used one. The properties of new formulation are the viscosity index of 140 and improved thermal stability consists of VHVI base oil. Field test results showed the possibility of extension of fluid life. Additionally, for development of high performance product, new required propertied and performances were discussed.

• Tribology and Lubricants
• /
• v.26 no.2
• /
• pp.97-104
• /
• 2010

A new magnetoelastic technique of oil viscosity measurement, where the oil viscosity is estimated by frequency shift of natural oscillations of magnetoelastic ribbon, is implemented in this study. Laboratory tests of the detector prototype are performed for measurement of viscosity of base synthetic and mineral oils. It was found that measurement accuracy was better when damping factor was estimated in comparison with accuracy of frequency of damped oscillations. Thus the oil viscosity was calibrated as a function of number of pulses of the damped oscillations of magnetoelastic ribbon. Result generally showed that developed detector is promising for in line oil viscosity measurement in wide viscosity range from 10 cSt up to 600 cSt, while the viscosity measurement was relatively instable when the viscosity of test oil was over 400 cSt.

• Tribology and Lubricants
• /
• v.29 no.4
• /
• pp.242-247
• /
• 2013

This study aims to establish the fundamental basis for the design of materials used in high-speed trains, by using a lab-scale dynamometer to evaluate the characteristic behavior of metallic sintered friction materials in relation to the shape of graphite. The test results clearly demonstrate that when flake graphite and granular graphite are added equivalently, the average coefficient of friction is much lower, and it is less influenced by speed variation; moreover, friction wear is observed to be insignificantly low. Adding flake graphite increases the coefficient of friction, which leads to higher friction wear. In addition, the roughness of the disc surface was equivalent regardless of the shape of the graphite.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.47-54
• /
• 1995

An advanced liquid lubricants for heat engines has been developed and tested successfully in a prototype engine. The lubricant possesses superior oxidation stability and high temperature stability and is capable of surviving for a minimum of three minutes at 425$^{\circ}$C (800$^{\circ}$C) at the ring zone and maintains stability at an oil sump temperature of 171$^{\circ}$C. The lubricant has been evaluated by the Cummins Engine Co. Out of a field of several dozens of lubricant, six lubricant was selected for a prototype 200 hours endurance testing. The NIST lubricant was one of the two lubricants that successfully finished the endurance testing. This paper describes the key lubricant considerations including oxidation and thermal stability, volatility, deposit control. The engine test conditions and the results will be presented.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.66-70
• /
• 1995

In this investigation, a controlled-environment tribological test device has been used to study the friction coefficients of several grades of commercially-available coated and uncoated cemented carbide cutting tools in a dry air environment at different environmental chamber pressures. Tests were run in the block-on-ring configuration. The results suggest that the friction coefficient is sensitive to the level of air present, with a noticeable rise in friction coefficient with decreasing pressure or increasing vacuum level. The uncoated cemented carbide sufaces resulted in the highest friction values, whereas the coated grades yielded somewhat lower values even after the coating was removed. The results suggest the importance of friction control in the design of coatings for metal removal processes.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.78-86
• /
• 1995

The silicon nitride based ceramic cutting tool materials have been fabricated by gas pressure sintering (GPS) or hot pressing (HP). Their mechanical properties were measured and the effect of the fabrication variables on the properties were examined. Also, effect of adding TiN or TiC particulates on the mechanical properties of the silicon nitride ceramics were investigated. Ceramic cutting tools (ISO 120408) were made of the sintered bodies. Cutting performance test were performed on either conventional or NC lathe. The workpieces were grey cast iron, hardened alloy steel (AISI 4140, HRc>60) and Ni-based superalloy (Inconel 718). The results showed that fabrication variables, namely, sintering temperature and time, exerted a strong influence on the microstincture and mechanical properties of the sintered body, which, however, did not make much difference in wear resistance of the tools. High hardness of the tool containing TiC particulates exhibited good cutting performance. Extensive crater wear was observed on both monolithic and TiN-containing silicon nitride tools after cutting the hardened alloy steel. Inconel 718 was extremely difficult to cut by the current cutting tools.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.26-30
• /
• 1995

Sliding experiments have been conducted on alumina and silicon carbide ceramics. Wear and friction data of both materials indicate that wear proceeds in two distinct stages. The wear occurs by a relatively mild plastic-grooving process in the initial stage, but eventually gives way to a severe grain pull-out process after a defined period of sliding test. The datails of the transition mechanism are presented. The effects of grain size and second phase particle on the wear transition are also presented.

• Tribology and Lubricants
• /
• v.17 no.6
• /
• pp.417-426
• /
• 2001

The effect of silver particle introduction on the rolling friction of AISI 52100 steel pairs has been investigated. Experiments ware performed in dry conditions using a thrust bearing-type rolling test rig at a load range of 12-960 N and a sliding velocity range of 8-785 mm/sec with pure (99.99%) silver particles. Results showed that introduced silver particles formed transfer layers, which protected the virgin bearing surfaces and resulted in the low lolling friction. By changing the quantity of silver particles, transitions in the rolling friction were found. Results also showed that the variations in normal load and rolling speed also affected the rolling friction behavior. Analyses of SEM and EPMA showed that the formation the transfer layer was mainly governed by the silver particle quantity, normal load and rolling speed, and this resulted in the different behavior of rolling friction. In this study, it was found that the low and stable rolling friction was resulted from the, shakedown phenomena occurred at the silver transfer layer.

• Tribology and Lubricants
• /
• v.17 no.6
• /
• pp.482-489
• /
• 2001

Changes in light transmission characteristics caused by various types of oil contaminations were experimentally measured with a built-in type wear monitoring device. Three kinds of iron powders of different size distribution, carbon duct, two kinds of solutions and grease were used for the test contaminants in this work. Light intensity of the transmitted light was measured with the contamination level. Results showed that the transmitted light intensity decreased linearly with the contamination concentration in the oil and the slope was affected by the size distribution. Light attenuation was also caused greatly by carbon dust, water contamination and poly-meric fibers in terms of the light absorption. As a result, it was proved that the optical measurement device could be applicable effectively for detecting any significant change in lubricating oils.