• 전기학회논문지
• /
• 제57권12호
• /
• pp.2194-2198
• /
• 2008

In this paper, the construction of secondary reaction plate is analyzed by 3-D Finite Element Method(3-D FEM) to consider the influence of its variation on the transverse edge effect of LIM. The effective 3-D analysis model for considering the transverse edge effect caused by the finite widths of the primary and the secondary is proposed. The simple method measuring the transverse edge effect by using the patterns of currents induced in the secondary reaction plate is also proposed. With this effective analysis method, various models of secondary reaction plate with overhang and cap has been analyzed to consider the relationship between the construction of secondary reaction plate and the transverse edge effect of LIM.

• 전기의세계
• /
• 제23권4호
• /
• pp.39-45
• /
• 1974

In most previous research work, the transverse edge effect has been allowed for only by use of a relativity-increase factor. This paper gives a more exact treatment. A two-dimensional-field analysis is presented for the problem of sheet rotor linear induction motor with finite width the method used takes account of flux leakage in the space between the stator and secondary sheet rotor as well as in the secondary itself. Equations are derived for the flux density distribution in the air gap and for the starting face, in each case as a function of stator current. The cross gap flux density peaks towards athe edge of the stator. This phenomena is known as the transverse edge effect. Measurements of the flux density in the air gap and starting force on a linear induction motor with sheet rotor of different width showed a reasonable agreement,suggest that it would be desirable to take into account also, at least for this motor in which severe redistribution occurs.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 추계학술대회 논문집 학회본부
• /
• pp.329-332
• /
• 1988

In this paper, A analysis method about air gap field of L.I.M. considering Transverse Edge Effect is suggested. Especially, the case of displacement of primary and secondary it can be analysed and criteria for design of L. I. M. is proposed by proving the influance of ratio of width for primary and secondary to the characteristic

• 한국정보기술학회 영문논문지
• /
• 제9권2호
• /
• pp.107-113
• /
• 2019

In this study, we examined the feasibility of considering the transverse edge effect of flat type linear induction motor as 2D finite element analysis (FEA) by changing the resistivity of secondary conductor. For this purpose, the 3D FEA analysis results were compared with the 2D FEA analysis results with the change of the resistivity of the secondary conductors. As a result, simply changing the resistivity could not accurately account for the transverse edge effect of LIM because of leakage components that could not be considered by 2D FEA.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1983년도 하계학술회의강연.논문초록집
• /
• pp.66-67
• /
• 1983

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.405-408
• /
• 2009

Edge cracks in cold rolling always influence to the quality of productions, while the "V" shaped cracks were propagated by passing the roll gap. We set up the sizes and shapes of initial cracks in simulation according to the references from real productions. Different to in hot rolling, the cracks in cold rolling couldn't be reduced from propagation automatically after generated, even if these could be reduced by changing the process parameters. In this paper, we described the affections of process parameters on the propagation of edge cracks, such as reduction ratio and tension. We predicted that the dependence of the cracks propagations of changing of process conditions and expected to gain the smaller edge cracks. By raising the reduction ratio, the cracks were propagated increasingly in both transverse and rolling directions. And as tension raise, the cracks became propagated in both directions in which transverse direction was less effectively.

• 대한전기학회논문지
• /
• 제39권1호
• /
• pp.29-35
• /
• 1990

This paper proposes a tow-dimensional magnetic flux distribution analysis of the double-sided linear induction motor(DLIM). Both the longitudinal end-effect and the transverse edge-effect, which are due to the finite length and width of the primary stator, are considered. Also each force which is due to the variation of slip frequency was computed to show the fact that the thrust force of DLIM is dependent on both the longitudinal end-effect and the transverse edge-effect. To ascertain the propriety of this analysis, the simulated results of the magnetic flux density distribution in the airgap are compared to the experimental data.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1974년도 학술발표회초록
• /
• pp.29-35
• /
• 1974

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.251-251
• /
• 2010

Linear induction motor performance for a light-weight urban transit has been established and verified. In this paper, linear induction motor is analyzed by finite-element method to consider influence of construction of secondary reaction plate on the transverse edge effect. With this effective analysis method, various models with overhang and cap have been analyzed to consider the relationship between the construction of secondary reaction plate and the transverse edge effect.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2008년도 Asian Magnetics Conference
• /
• pp.96.2-96.2
• /
• 2008