• Computers and Concrete
• /
• v.24 no.6
• /
• pp.513-525
• /
• 2019

In this work, an experimental research has been performed on Steel Fiber-Steel Reinforced Concrete (SFSRC)specimens subjected to four-point bending tests to evaluate the feasibility of mutual replacement of steel fibers and conventional reinforcement through studying failure modes, load-deflection curves, stiffness of characteristic points, stiffness degradation curves and damage analysis. The variables considered in this experiment included steel fiber volume percentage with and without conventional reinforcements (stirrups or steel fibers) with shear span depth ratios of S/D=2.5 and 3.5. Experimental results revealed that increasing the volume percentage of steel fiber decreased the creation and propagation of shear and bond cracks, just like shortening the stirrups spacing. Higher crack resistance and suturing ability of steel fiber can improve the stability of its bearing capacity. Both steel fibers and stirrups improved the stiffness and damage resistance of specimens where stirrups played an essential role and therefore, the influence of steel fibers was greatly weakened. Increasing S/D ratio also weakened the effect of steel fibers. An equation was derived to calculate the bending stiffness of SFSRC specimens, which was used to determine mid span deflection; the accuracy of the proposed equation was proved by comparing predicted and experimental results.

• Structural Monitoring and Maintenance
• /
• v.5 no.4
• /
• pp.489-506
• /
• 2018

This paper reported test of full-scale cables attached with four types of dampers: viscous damper, passive Magneto-Rheological (MR) damper, friction damper and High Damping Rubber (HDR) damper. The logarithmic decrements of the cable with attached dampers were calculated from free vibration time history. The efficiency ratios of the mean damping ratios of the tested four dampers to theoretical maximum damping ratio were derived, which was very important for practical damper design and parameter optimization. Non-ideal factors affecting damper performance were discussed based on the test results. The effects of concentrated mass and negative stiffness were discussed in detail and compared theoretically. Approximate formulations were derived and verified using numerical solutions. The critical values for non-dimensional concentrated mass coefficient and negative stiffness were identified. Efficiency ratios were approximately 0.6, 0.6, and 0.3 for the viscous damper, passive MR damper and HDR damper, respectively. The efficiency ratio for the friction damper was between 0-1.0. The effects of concentrated mass and negative stiffness on cable damping were positive as both could increase damping ratio; the concentrated mass was more effective than negative stiffness for higher vibration modes.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.3 no.1
• /
• pp.31-46
• /
• 1978

Consider a time interval during which the demand for trips is fixed (e.g. the rush hour period). The traveller has a choice between various public modes, whose travel times and fares are fixed, and the automobile mode, for which travel time and cost depend on the volume of traffic flow on those roads, which are subject to congestion. We consider the equilibrium in terms of a representative travellerm, who choses for any trip the mode and route with the least combined money and time cost. When several (parallel) model or routes are chosen, then the combined cost of money and time must be equal among these. Our problem is first, to find the optimal flows of cars and of public mode carriers on the various links of their networks and second the optimal fares for trips by the variousmodes. The object is to minimize the total operating costs of the carriers and car plus the total time costs to travellers. The optimal fares are related to, but not identical with the dual variables of the underlying Nonlinear Program. They are equal to these dual variables only in the case, when congestion tolls on trips or on the use of specific roads are collected from automobile users. When such tolls are not collected, they must be passed on as subsidies to travellers using competing modes. The optimal fares of public modes are then reduced by the amounts of these subsidies. Note that subsidies are not a flat payment to public carriers, but are calculated on the basis of tickets sold. Fares and subsidies depend in general on tile period considered. They will be higher during periods of higher demand. When the assumption of fixed trip demand is relaxed, this tare system is no longer best, but only second best since too much traffic will, in general, be generated. The Free Rider Theorem states the following : Suppose road tolls can be charged, so that a best pricing system for public modes is posssible. Then there may exist free rides on some routes and modes, but never on a complete round trip.

• Journal of Biosystems Engineering
• /
• v.27 no.5
• /
• pp.409-416
• /
• 2002

This study was conducted to develop a vehicle, leading or following a worker at a certain distance to assist laborious transporting works in greenhouses. A prototype vehicle, which consisted of the rear driving, the front steering and the console units, was designed and tested in the ideal indoor conditions. Results of this study were summarized as following: 1. The driving unit was designed to travel at the speed ranges of 0.3∼0.8 m/sec depending on the operating modes with a maximum payload of 100 kg. 2. The console unit consisted of a main-board including a 80C196KC microprocessor and peripheral devices, a power-board and safety interlock. Worker-leading, and following modes were available in automatic and manual modes. 3. Steering was achieved by turning the steering motor against the sensed direction. Proper steering angles for correcting travel direction were determined as 5 and 9 degrees when sensing cultivation beds and plants, respectively.

• Journal of the Korean Society for Railway
• /
• v.16 no.4
• /
• pp.253-261
• /
• 2013

According to the measured results of KTX brake squeal noise in this study, high level brake noise occurred in a wide frequency range, 100~18,000Hz. To identify the sources of the brake squeal noise, unstable vibration modes due to brake disc/pad interaction were analyzed under various conditions by the finite element method. Complex eigenvalues for a brake unit with a disc and four pads were obtained. It was found that the real parts of the complex eigenvalues, that is, unstable vibration modes, were closely related to friction coefficients, pressure on the brake cylinders, elastic moduli of the components, and other conditions.

• Journal of the Society of Naval Architects of Korea
• /
• v.61 no.1
• /
• pp.29-43
• /
• 2024

The present study concerns a feasibility study for applying principal component analysis to ship dynamics in maneuver. Using the four degrees of freedom standard modular model for ship dynamics maneuver simulations of large angle zigzag tests with rudder deflection angle variations are conducted. The datasets of ship motion, hydrodynamic force, and moment during the maneuver are acquired to identify the principal modes. The covariance matrix of obtained ship dynamics variables shows a strong linear correlation between the motion, hydrodynamic force, and moment, except the surge force. Four eigenvectors of the covariance matrix are selected as the principal modes of ship dynamics. Using the principal modes, ship motion in turning circle and zigzag tests is reconstructed, showing good agreement with the original data.

• Journal of Applied Reliability
• /
• v.17 no.1
• /
• pp.11-21
• /
• 2017

Purpose: The occurrence ranks of failure modes can come from the real failure but the severity ranks of failure modes require a highly subjective point of view of users. The severity ranks have to find more objective and scientific values. Methods: We found the optimal values by using the correlation analysis between failure mode effects and the criticality number like RPN (Risk Priority Number) in RCM. Result: This paper shows the result that verified whether the weighted values on each failure effect in criticality number calculation is suitable to the actual failures or not. To get the verification, it used the 5 year data and correlation analysis. Based on the analyzed result, We proposed the more suitable values. Conclusion: This correlation analysis approach can provide guidance of RCM analysis across many industries and situations.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.9
• /
• pp.53-63
• /
• 1994

In indoor radio systems, vehicular communication systems, and land mobile systems, a very important problem is that of maintaining stable communications at all locations. Therefore solutions for the indoor propagation problem are important aspects of the mobile communication system. leaky coxial cables are finding increasing use in communications systesm involving mines, tunnels, tailroads, and highways, and in new obstacle detection, or guided radar, schemes for ground transportation and perimenter surveilance. In this paper a leaky coaxial cable having periodic slots in the outer conductor is described to obtain the propagation modes in the various environments. We use aneccentric cylindrical model to develop the theory for surface-wave propagation on the cable. Numerical Results are also included for the propagation constants, field distribution and current distribution. First, we derive the electromagnetic equation for leaky coaxial cable having symmetrical periodic slots using mode-matching method and Floquet's theorem, and then find various modes, propagation constants, field distribution, etc.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.102-108
• /
• 2000

Due to the rapid increase of long-distance transportation, particular attentions have been paid to truck tires, especially to their dynamic characteristics. In this research, experimental modal analysis on two kinds of light-truck tires, i.e., radial tire and bias tire, are performed by using GRFP(global rational fraction polynomial) method to investigate differences of the dynamic behavior of the two tires. The test results have shown that the modal frequencies of bias tire are much higher than their corresponding values of radial tire with a similar mode shape, which is in accordance with the fact that the radial rigidity of bias tire is higher than that of radial tire. And most of the modal decay rates of bias tire are larger than those of radial tire within the scope of this experiment. In the frequency domain range of test, the bias tire has extra modes, which do not occur in the radial tire. This difference is based on the fact that the circumferential rigidity of the bias tire is quite low whereas that of radial tire is so high that the frequencies of the corresponding modes are out of the frequency range of test.

• Journal of Urban Science
• /
• v.9 no.2
• /
• pp.63-68
• /
• 2020

In recent years, the planning of livable communities has emerged as a new paradigm. The concept of livable communities is related to both the spatial balance of working, playing, and living and the promotion of green modes of transportation, such as walking and biking. This study uses a disaggregate travel survey conducted by the Seoul Metropolitan Area in 2006. I applied a multi-level random intercept logit model to estimate the effects of land-use characteristics on the choice of green modes, holding a traveler's socio-demographic characteristics constant. The empirical results show that higher density and more mixed land-use development encourages people to walk and bike even when individuals have the same socio-economic characteristics. This paper demonstrates that land-use planning by itself can play a role in the creation of livable cities and the decline of greenhouse gas production.