• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.379-379
• /
• 2007

The characteristics of indium-zinc-tin-oxide (IZTO)-Ag-IZTO multilayer grown on a PET substrate were investigated for flexible organic light-emitting diodes. The IZTO-Ag-IZTO (IAI) multilayer anode exhibited a remarkably reduced sheet resistance of 4 ohm/sq and a high transmittance of 84%, despite the very thin thickness of the IZTO (30 nm) layer. In addition, it was shown that electrical and optical properties of IAI anodes are critically dependent on the thickness of the Ag layer, due to the transition of Ag atoms from distinct islands to continuous films at a critical thickness (14 nm). Moreover, the IAI/PET sample showed more stable mechanical properties than an amorphous ITO/PET sample during the bending test due to the existence of a ductile Ag layer. The current density voltage-luminance characteristics of flexible OLEDs fabricated on an IAI/PET substrate was better than those of flexible OLEDs fabricated on an ITO/PET substrate. This indicates that IAI multilayer anodes are promising flexible and transparent electrodes for flexible OLEDs.

• Korean Journal of Materials Research
• /
• v.29 no.4
• /
• pp.228-232
• /
• 2019

Copper electroplating and electrode patterning using a screen printer are applied instead of lithography for heterostructure with intrinsic thin layer(HIT) silicon solar cells. Samples are patterned on an indium tin oxide(ITO) layer using polymer resist printing. After polymer resist patterning, a Ni seed layer is deposited by sputtering. A Cu electrode is electroplated in a Cu bath consisting of $Cu_2SO_4$ and $H_2SO_4$ at a current density of $10mA/cm^2$. Copper electroplating electrodes using a screen printer are successfully implemented to a line width of about $80{\mu}m$. The contact resistance of the copper electrode is $0.89m{\Omega}{\cdot}cm^2$, measured using the transmission line method(TLM), and the sheet resistance of the copper electrode and ITO are $1{\Omega}/{\square}$ and $40{\Omega}/{\square}$, respectively. In this paper, a screen printer is used to form a solar cell electrode pattern, and a copper electrode is formed by electroplating instead of using a silver electrode to fabricate an efficient solar cell electrode at low cost.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.6
• /
• pp.1-6
• /
• 2011

A transparent oxide thin film transistors (Transparent Oxide-TFT) have been fabricated by RF magnetron sputtering at room temperature using amorphous indium zinc oxide (a-IZO) as both of active channel and source/drain, gate electrodes and co-sputtered $HfO_2-Al_2O_3$ (HfAIO) as gate dielectric. In spite of its high dielectric constant > 20), $HfO_2$ has some drawbacks including high leakage current and rough surface morphologies originated from small energy band gap (5.31eV) and microcrystalline structure. In this work, the incorporation of $Al_2O_3$ into $HfO_2$ was obtained by co-sputtering of $HfO_2$ and $Al_2O_3$ without any intentional substrate heating and its structural and electrical properties were investigated by x-ray diffraction (XRD), atomic force microscopy (AFM) and spectroscopic ellipsometer (SE) analyses. The XRD studies confirmed that the microcrystalline structures of $HfO_2$ were transformed to amorphous structures of HfAIO. By AFM analysis, HfAIO films (0.490nm) were considerably smoother than $HfO_2$ films (2.979nm) due to their amorphous structure. The energy band gap ($E_g$) deduced by spectroscopic ellipsometer was increased from 5.17eV ($HfO_2$) to 5.42eV (HfAIO). The electrical performances of TFTs which are made of well-controlled active/electrode IZO materials and co-sputtered HfAIO dielectric material, exhibited a field effect mobility of more than $10cm^2/V{\cdot}s$, a threshold voltage of ~2 V, an $I_{on/off}$ ratio of > $10^5$, and a max on-current of > 2 mA.

• Korean Journal of Materials Research
• /
• v.30 no.4
• /
• pp.204-210
• /
• 2020

ZnO thin films are of considerable interest because they can be customized by various coating technologies to have high electrical conductivity and high visible light transmittance. Therefore, ZnO thin films can be applied to various optoelectronic device applications such as transparent conducting thin films, solar cells and displays. In this study, ZnO rod and thin films are fabricated using aqueous chemical bath deposition (CBD), which is a low-cost method at low temperatures, and environmentally friendly. To investigate the structural, electrical and optical properties of ZnO for the presence of citrate ion, which can significantly affect crystal form of ZnO, various amounts of the citrate ion are added to the aqueous CBD ZnO reaction bath. As a result, ZnO crystals show a nanorod form without citrate, but a continuous thin film when citrate is above a certain concentration. In addition, as the citrate concentration increases, the electrical conductivity of the ZnO thin films increases, and is almost unchanged above a certain citrate concentration. Cu(In,Ga)Se₂ (CIGS) solar cell substrates are used to evaluate whether aqueous CBD ZnO thin films can be applicable to real devices. The performance of aqueous CBD ZnO thin films shows performance similar to that of a sputter-deposited ZnO:Al thin film as top transparent electrodes of CIGS solar cells.

• Applied Chemistry for Engineering
• /
• v.16 no.6
• /
• pp.742-748
• /
• 2005

Transparent conductive indium-tin oxide (ITO) films are widely used as transparent electrodes for flat panel displays. Many of the ITO films for practical use have been prepared by magnetron sputtering, chemical vapor deposition, electron beam evaporation, etc. An oxide target composed of 10 wt% $SnO_2$ and 90 wt% $In_2O_3$ has been deposited onto polycyclic olefin polymer (POP) substrate by electron beam evaporation. POP has a higher glass transition temperature ($Tg=330^{\circ}C$) than other conventional polymers. In this study, the effects of substrate temperature and the $O_2$ introduction flow rate were investigated in terms of physical, electrical and optical properties of deposited ITO films. We investigated the effects of processing variables such as substrate temperature and the oxygen introduction flow rate. The best electrical and optical properties of deposited ITO films obtained from this study were electrical resistivity value of ${\rho}=1.78{\times}10^{-3}{\Omega}{\cdot}cm$ and optical transmittance of about 85% at 8 sccm (Standard Cubic Centimeter per Minute) $O_2$ introduction flow rate, $5{\AA}/sec$ deposition rate, $1000{\AA}$ deposited ITO thickness and $200^{\circ}C$ substrate temperature.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.383-383
• /
• 2014

최근 디스플레이, 태양전지 그리고 touch screen panels 등 optoelectronic 장치의 시장이 성장함에 따라 투명전극의 수요가 증가하고 있다. Indium tin oxide (ITO)의 좋은 특성 때문에 주로 투명전극에 많이 사용되고 있다. 그러나 화학적 안정성이 떨어지고, 휘어질 때 특성저하가 심하여 금속나노와이어, 탄소나노튜브, 전도성폴리머, 그리고 그래핀 등의 다른 투명전극의 연구가 활발히 진행되고 있다. 그 중에서 그래핀은 높은 전자 이동도(200000 cm2v-1s-1)와 휘어져도 전기적 크게 변하지 않는 특성 때문에 유망한 투명 전도성 전극 (Transparent Conductive Electrodes, TCEs)으로 연구되어왔다. 또한 다양한 속성 가운데, 높은 광 투과성은 그래핀의 가장 큰 장점이다 [1]. 최근, 화학 기상 증착 (Chemical Vapor Deposition, CVD) 등 다양한 제조 방법이 대량 생산을 위해 개발되었다. 그러나 이 방법은 비용이 많이 들며, 과정이 상당히 복잡하고 높은 온도 (${\sim}1000^{\circ}C$)를 필요로 한다. 따라서 용매 기반의 환원된 그래핀 산화물(Reduced Graphene Oxides, RGOs)이 최근 주목 받고 있다. 그러나 RGOs의 면저항이 높아 전극으로서 사용이 제한된다. 따라서 전기적 특성을 향상시키는 방법으로 단일 벽 탄소 나노튜브 (Single-Walled Carbon Nanotubes, SWNTs)를 혼합하거나 화학적 도핑을 통하여 면저항을 크게 향상시키는 연구가 활발히 진행되고 있다. 그러나 이런 화학적 도핑의 경우 박막이 공기 중에 직접 산소나 습기와 반응하여 전기적 특성이 저하되는 문제점을 가지고 있다 [2]. 이러한 문제를 해결하기 위해 AuCl3을 도핑한 박막에 내열성 및 내광성 등의 화학적 안정성이 뛰어난 PEDOT:PSS를 코팅하여 필름의 공기중의 노출을 막아 줌으로써 도핑의 안전성 및 전기적 특성을 최적화하였다. 본 연구에서는 간단한 dip-coating방법을 사용하여 4개의 RGO/SWNTs 박막을 흡착하였다. 다음으로 AuCl3를 도핑하여 면저항 $4.909K{\Omega}$, $4.381K{\Omega}$인 두 개의 샘플의 시간과 온도에 따른 면저항의 변화를 확인하였다. 그리고 필름의 도핑 안전성을 향상 시키기 위해 AuCl3를 도핑한 필름 위에 전도성 폴리머 PEDOT:PSS 코팅하여 면저항 $886.1{\Omega}$, $837.5{\Omega}$인 두 개의 샘플의 시간과 온도에 따른 면저항의 변화를 확인하였다. AuCl3 도핑된 필름의 경우 공기 중에 150시간 노출 시 72%의 면저항 증가가 발생하였지만 PEDOT:PSS가 코팅된 필름의 경우 5%의 면저항 증가가 나타나 확연한 차이를 보였다. 또한 AuCl3 도핑한 필름의 경우 $150^{\circ}C$에서 60시간동안 공기중에 노출되었을 때 525%의 면저항 증가가 발생하였지만 PEDOT:PSS가 코팅된 필름의 경우 58%의 면저항 증가를 나타내었다. 이것은 PEDOT:PSS가 passivation역할을 하여 필름이 공기에 노출된 부분을 막아주어 도핑된 필름의 면저항의 변화를 줄여 주었음을 알 수 있다.

• Journal of the Korean Society of Radiology
• /
• v.3 no.1
• /
• pp.17-21
• /
• 2009

The Recently, large area matrix-addressed image detectors are investigated for X-ray imaging with medical diagnostic and other applications. In this paper, a new flat panel gas detector for diagnostic X-ray imaging is proposed, and its characteristics are investigated. The research of flat panel gas detector is not exist at all. Because of difficulty to inject gas against to atmospheric pressure. So almost gas detector made by chamber shape. We made flat panel sample by display technique. (ex: PDP, Fed, etc.) The experimental measurements, the transparent electrodes, dielectric layer, and the MgO protection layer were formed in front glass. And, the X-ray phosphor layer and address electrodes are formed in the rare glass. The dark current, the x-ray sensitivity and linearity as a function of electric field were measured to investigate the electrical properties. From the results, the stabilized dark current density and the significant x-ray sensitivity were obtained. And the good linearity as a function of exposure dose was showed in wide diagnostic energy range. These results means that the passive matrix-addressed flat panel gas detector can be used for digital x-ray imaging.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.404-404
• /
• 2012

저차원계 탄소 동소체는 특유의 구조에서 기인하는 우수한 물리적 성질로 인해 각광받고 있는 물질이다. 탄소원자가 육각형 격자 모양을 지닌 2차원계 물질인 그래핀(graphene)은 뛰어난 전기적, 물리적, 광학적 성질로 인해 전계효과 트랜지스터(field effect transistors), 투명전극(transparent electrodes), 에너지 저장체, 복합체, 화학/바이오 센서 등 다양한 분야에서 활용을 위한 연구가 진행되고 있다. 또한 그래핀이 튜브형태로 말려있는 1차원계 물질인 탄소나노튜브(carbon nanotube)의 전기적, 열적, 기계적 성질은 이를 전계방출 디스플레이(field emission display), 전도성 플라스틱, 가스 저장체, 슈퍼 커패시터 등에 적용가능하게 한다. 최근 2차원계 물질인 그래핀과 1차원계 물질인 탄소나노튜브의 장점을 극대화하기 위한 복합 나노 구조에 대한 다양한 연구가 진행되고 있는 추세이다[1-5]. 본 연구에서 그래핀-탄소나노튜브 혼성 구조의 제작은 다음과 같이 진행되었다. 우선 열 화학기상증착법(thermal chemical vapor deposition)을 이용하여 그래핀을 합성하였다. 합성된 그래핀은 메타크릴산메탈 수지(polymetylmethacrylate; PMMA)를 이용한 전사(transfer)방법을 이용하여 원하는 기판에 위치시키고, 직류 마그네트론 스퍼터링(DC magnetron sputtering)을 이용하여 탄소나노튜브의 합성을 위한 촉매층을 증착하였다. 이후 열 화학기상증착법을 이용하여 그래핀 위에 탄소나노튜브를 합성함으로써 그래핀-탄소나노튜브 혼성 구조를 제작하였다. 합성된 그래핀-탄소나노튜브의 구조적 특징은 주사 전자 현미경(scanning electron microscopy)을 통해 확인하였고, 촉매의 표면 형상 및 화학적 상태는 원자힘 현미경(atomic force microscopy)과 X선 광전자 분광법(X-ray photoelectron spectroscopy)을 통해 확인하였다. 또한 제작된 그래핀-탄소나노튜브의 전기적 특성 측정을 통해 나노전자소자로의 응용가능성을 조사하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.1
• /
• pp.25-30
• /
• 2020

Oxide (SiO₂)/Metal(Ag)/Oxide(SiO₂, ITO, ZnO) multilayer films were fabricated using a magnetron sputtering technique at room temperature on Si (p-type, 100) and a glass substrate. The electrical and optical properties of the asymmetric multilayer films depended on the thickness of the mid-layer film and the type of oxide in the bottom layer. As the metal layer becomes thicker, the sheet resistance decreases. However, the transmittance decreases when the metal layer exceeds a threshold thickness of approximately 10~12 nm. In addition, the sheet resistance and transmittance change according to the type of oxide in the bottom layer. If the oxide has a large resistivity, the overall sheet resistance increases. In addition, the anti-reflection effect changes according to the refractive index of the oxide material. The optical and electrical properties of multilayer films were investigated using an ultraviolet visible (UV-Vis) spectrophotometer and a 4-point probe, respectively. The optimum structure is SiO₂ (30 nm)/Ag (10 nm)/ZnO (30 nm) multilayer, with the highest FOM value of 7.7×10^-3 Ω^-1.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.4
• /
• pp.344-349
• /
• 2005

The optical and electrical characteristics of plasma display panel(PDP) using the vacuum in-line sealing technology compared with the conventional sealing process in this research. This PDP consisted of MgO protecting layer by e-beam evaporation and battier rib, transparent dielectric layer, dielectric layer, and electrodes by screen printer and then sealed off on Ne-Xe(4 ％) 400 Torr and 430。C. The brightness and luminous efficiency were good as the base vacuum level was higher, and it was to check the advantage of high vacuum level sealing, one of the strong points of the vacuum in-line sealing process. However, the brightness and luminous efficiency was dropped sharply because of a crack on MgO protecting layer by the difference of the expansion and contraction stress on high temperature in the vacuum states between MgO and substrate. Fortunately, the crack was prevented by MgO was deposited on higher temperature than 300。C. Finally, the PDP, was fabricated by the vacuum in-line sealing process, resulted the lower brightness than processing only the thermal annealing treatment in the vacuum chamber, but the luminous efficiency was increased by the reducing power consumption with the decreasing luminous current. The vacuum in-line sealing technology was not to need the additional thermal annealing process and could reduce the fabrication process and bring the excellent optical and electrical properties without the crack of MgO protecting layer than the conventional sealing process.