• International Journal of Aeronautical and Space Sciences
• /
• v.13 no.3
• /
• pp.317-322
• /
• 2012

The low speed aerodynamic characteristics for a modified sonic arc airfoil which is designed by using the nose shape function of sonic arc, the shape function of NACA four-digit wing sections, and Maple are experimentally investigated. The small rotor blades of a modified sonic arc and NACA0012 airfoil are precisely fabricated with a commercially available light aluminum(Al 6061-T6) and are spin tested over a low speed range (3000rpm-5000rpm). In a consuming power comparison, the consuming powers of NACA0012 are higher than that of modified sonic arcs at each pitch angle. The measured rotor thrust for each pitch angle is used to estimate the rotor thrust coefficient according to momentum theory in the hover state. The value of thrust coefficients for both two airfoils at each pitch angle show almost constant values over the low Mach number range. However, the rotor thrust coefficient of NACA0012 is higher than that of the modified sonic arc at each pitch angle. In conclusion, the aerodynamic performance of NACA0012 is better than that of modified sonic arcs in the low speed regime. This test model will provide a convenient platform for improving the aerodynamic performance of small scale airfoils and for performing design optimization studies.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.2
• /
• pp.139-145
• /
• 2012

The low speed aerodynamic characteristics of modified sonic arc airfoil which is developed to fit the transonic regime are investigated. This airfoil is designed by using the shape function of sonic arc proposed by Schwendenman, the data of NACA0012, and commercial program Maple. In order to investigate the low speed aerodynamic characteristic of sonic arc airfoil, the numerical analysis is conducted below Mach number 0.3 and the results are compared and analyzed with it of NACA0012 airfoil. At each Mach number, the drag of modified sonic arc airfoil is less 1.5% than NACA0012's drag and the lift of modified sonic arc airfoil is less 2% than NACA0012's lift. The moment coefficient of modified sonic arc airfoil is also less 1.4% than it of NACA0012 at each Mach number.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.495-509
• /
• 2019

The objective of this study is to analyze the compressibility effects of multiphase cavitating flow during the water-entry process. For this purpose, the water-entry of a projectile at transonic speed is investigated computationally. A temperature-adjusted Tait equation is used to describe the compressibility effects in water, and air and vapor are treated as ideal gases. First, the computational methodology is validated by comparing the simulation results with the experimental measurements of drag coefficient and the theoretical results of cavity shape. Second, based on the computational methodology, the hydrodynamic characteristics of flow are investigated. After analyzing the cavitating flow in compressible and incompressible fluids, the characteristics under compressible conditions are focused upon. The results show that the compressibility effects play a significant role in the development of cavitation and the pressure inside the cavity. More specifically, the drag coefficient and cavity size tend to be larger in the compressible case than those in the incompressible case. Furthermore, the influence of entry velocities on the hydrodynamic characteristics is investigated to provide an insight into the compressibility effects on cavitating flow. The results show that the drag coefficient and the impact pressure vary with the entry velocity, and the prediction formulas for drag coefficient and impact pressure are established respectively in the present study.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.2
• /
• pp.51-57
• /
• 2012

Base pressure at the base of high-speed jet has long been one of the important issues from both the view points of fluid dynamics as well as practical engineering applications. The base pressure characteristics of incompressible flows have been well known to date. However, the base pressure at transonic or supersonic speeds would be different due to the compressibility effects and shock waves. In the present paper, a CFD study has been performed to understand the base pressure characteristics at transonic and supersonic speeds, prior to experimental work. An emphasis is placed on the control of the base pressure using a simple orifice. A variety of supersonic jet plumes have been explored to investigate the flow variables influencing the base pressure. The results obtained were validated with existing experimental data and discussed in terms of the base pressure and discharge coefficient of the orifice.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.1
• /
• pp.24-31
• /
• 2006

In the present study, a strongly coupled analysis code is developed for transonic flutter analysis. For aerodynamic analysis, two dimensional Reynolds-Averaged Navier-Stokes equation was used for governing equation, and ε-SST for turbulence model, DP-SGS(Data Parallel Symmetric Gauss Seidel) Algorithm for parallelization algorithm. 2 degree-of-freedom pitch and plunge model was used for structural analysis. To obtain flutter response in the time domain, dual time stepping method was applied to both flow and structure solver. Strongly coupled method was implemented by successive iteration of fluid-structure interaction in pseudo time step. Computed results show flutter speed boundaries and limit cycle oscillation phenomena in addition to typical flutter responses - damped, divergent and neutral responses. It is also found that the accuracy of transonic flutter analysis is strongly dependent on the methodology of fluid-structure interaction as well as on the choice of turbulence model.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.1
• /
• pp.97-102
• /
• 2013

A prestudy on expendable turbine engine for high-speed vehicle was conducted. After two possible mission profiles were established to decide the engine requirements, design point analysis was performed with the values of design parameter which were obtained from similar class engines, references, etc. The results showed that specific net thrust and specific fuel consumption with turbine inlet temperature of 3,600 R are 2,599.4 ft/s and 1.483 lb/(lb*h) respectively at the flight condition of sea level, Mach 1.2. It was also found that major design parameters for determining maximum net thrust were turbine inlet temperature for low supersonic and transonic flight speed and compressor exit temperature for high supersonic flight speed from the results of performance analysis on the two possible mission profiles. In addition, simple turbojet engine with an axial compressor, a straight annular combustor, an one stage axial turbine and a fixed throat area converge-diverge exhaust nozzle was proposed as the configuration of simple low cost lightweight turbine engine.

• 한국전산유체공학회:학술대회논문집
• /
• 1999.11a
• /
• pp.115-126
• /
• 1999

A two-dimensional Navier-Stokes solver using hybrid meshes is parallelized with a domain decompostion method. The focus of this paper is placed on minimizing the amount of effort in parallelizing the serial version of the solver, and this is achieved by adding an additional layer of cells to each decomposed domain. Most subroutines of the serial solver are used without modification, and the information exchange between neighboring domains is achieved using MPI(Message Passing Interface) library. Load balancing among the processors and scheduling of the message passing are implemented to reduce the overhead of parallelization, and the speed-up achieved by parallelization is measured on the transonic invisicd and turbulent flow problems. The parallelization efficiencies of the explicit Runge-Kutta scheme and the implicit point-SGS scheme are compared and the effects of various factors on the results are also studied.

• International Journal of Aeronautical and Space Sciences
• /
• v.7 no.1
• /
• pp.99-105
• /
• 2006

In this study, nonlinear static and dynamic aeroelastic analyses for a high-aspect-ratio wing have been performed. To achieve these aims, the transonic small disturbance (TSD) theory for the aerodynamic analysis and the large deflection beam theory considering a geometrical nonlinearity for the structural analysis are applied, respectively. For the coupling between fluid and structure, the transformation of a displacement from the structural mesh to the aerodynamic grid is performed by a shape function which is used for the finite element and the inverse transformation of force by work equivalent load method. To validate the current method, the present analysis results of a high-aspect-ratio wing are compared with the experimental results. Static deformations in the vertical and torsional directions caused by an angle of attack and gravity loading are compared with experimental results. Also, static and dynamic aeroelastic characteristics are investigated. The comparisons of the flutter speed and frequency between a linear and nonlinear analysis are presented.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.141-146
• /
• 1999

The comming of high speed computers with large memory size in recent years has allowed the practical development of codes which solve the Reynolds-averaged NAvier-Stokes (RANS) equations in three dimensions. Such codes are already used by the large engine manufacturers for the advanced design of some engine components. Different computational fluid dynamics approaches and turbulence models exist, and it seems essential today to establish their degree of validity for application to typical configurations in turbomachinery. In 1993 the Turbomachinery Committee of the IGTI of ASME has issued an open invitation to predict the flow details of an isolated transonic fan rotor called as NASA ROTOR 37. This paper reports this test case.

• 한국가시화정보학회:학술대회논문집
• /
• 2006.12a
• /
• pp.149-152
• /
• 2006

This paper describes the flow visualization around the model of a commercial passenger airplane, Boeing 747-400, which cruises in the transonic speed. The geometry was realized through the reverse engineering based on the photogrammetry. The three-dimensional inviscid steady compressible governing equations are solved in the unstructured grid system under the cruise condition and in a finite volume method. The convective term is processed by the Crank-Nicholson scheme and first order upwind scheme is applied. The lift and drag forces in the wing with engines increase by 1.49% End 3.9%, respectively compared with the wing without engines.