• Current Research on Agriculture and Life Sciences
• /
• v.8
• /
• pp.107-113
• /
• 1990

This study was attempted to develop a remote controllable speed sprayer in order to protect an operator from agricultural chemicals. For the purpose of remote controllable transmission was developed by using one chip microcomputer. The following results could be summarized in this study. 1. Remote controllable transmission developed had not made even a single mistake during the test performed 100 times repeat. Thus, it could that this machine was very accurate. 2. One chip microcomputer was made by machine language and its was with in 3 sec's which was the same as human did. 3. One chip microcomputer which was used in the experiment could be widely used to automation of agricultural machinery, since it is smaller and chiper than any other similar ones such as personal computer, lap tap, one board computer. 4. Since, farm tractor has the same type of transmission as this system, it also could be adapted to farm tractors. 5. In this experiment, transmission lever was remote controll were designed to operate simultaneously. Thus, this system developed was more complicate than conventional system. However, by removing this transmission lever and by mounting the remote controll system at the speed sprayer, it would be higher and easier to handle than the conventional one.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.5
• /
• pp.508-514
• /
• 2015

In this paper, the powertrain efficiency is analyzed for the input split type hybrid electric vehicle. For considering the powertrain loss, the power loss models of planetary gear and motor are applied. And, the mathematic equations of powertrain speed and torque are found by using the lever analogy. With the above models and equations, the powertrain efficiency is analyzed for the 0 to 180 km/h vehicle velocity range. From the analysis results, it is found that the transmission efficiency with the power loss of planetary gear is smaller maximum 2.1% than the transmission efficiency without the power loss of planetary gear.

• Journal of Biosystems Engineering
• /
• v.21 no.2
• /
• pp.134-145
• /
• 1996

Since the skid-steer loader is able to work for excavating, lifting and transporting load even at the narrow space, they are widely used in the regular farm and the livestock farm. The skid-steer loader normally adopts the hydrostatic transmission because the power to move the machine backward and forward should be delivered independently on both sides of wheels. Contrast to the mechanical system such as chain and belt transmissions, however, the hydrostatic transmission is less efficient in the use of energy and more difficult in the maintenance. This study was intended to investigate the feasibility of using triangular-type belt clutch and V-belt transmission for the newly developed skid-steer loader in order to overcome the problems stated in the hydrostatic transmission. In the developed triangular-type belt clutch, the centers of driving, driven and idler sheaves are arranged in the triangular shape in a plane, and V-belts were loaded loosely on three sheaves. The power is transmitted by pressing the idler connected to a lever on the loosened V-belt. Contrast to the normal belt clutch using two sheaves, the newly developed belt clutch has the characteristics of small contact-angle of the driving sheave at no bucket load and increasing contact-angle at the time of power transmission. The results of research can be summarized as follows: 1) The developed triangular-type belt clutch adopted a spring-loaded slackside idler which could transmit more power than a fixed idler could by sacrificing the belt life. The life of V-belt used in the power transmission reached at 500 hours(6 months) when the engine power of 11.8 ㎾ was transmitted. Also, it was feasible to develop the large industrial skid-loader with the V-belt transmission by using the proper set of sheaves. 2) The developed skid-steer loader changed the rotating radius and speed with bucket loads as the conventional skid steer loader did. The rotating speed was 47 deg/s at the maximum bucket load of 2.74 kN when the minimum rotating radius was 1.5m. 3) The power required in turning at the bucket load of 2.74 kN was 4 ㎾ and the slippage of V-belt was less than 1%.

• Journal of Biosystems Engineering
• /
• v.29 no.5 s.106
• /
• pp.407-418
• /
• 2004

There are several different types of continuously variable transmission(CVT) such as toroidal drive, belt drive, hydrostatic drive, hydro-mechanical drive. The toroidal CVT is an alternative to the manual transmission, HST, power-shift gear trans-missions or other CVTs. The driver of the CVT tractor doesn't have to operate a shia lever since the CVT controller automatically controls the speed of tractor. Thus, it is much easier to operate the CVT tractor. The fuel efficiency of CVT tractor can be increased since the controller responds quickly to the change in external load on the wheel during field operation. This study was conducted to develop the hardwares and softwares for the toroidal CVT controller which control the variator and the range clutches. The hardware consisted of a measurement system, hydraulic system and computer. And the PID controller was developed using the simulation model of the CVT control system. Through the simulation, the control coefficients for the PID controller were selected. Finally, the performance of the CVT control system was evaluated by step response test and torque response test. The settling time of the CVT control system appeared to be fast enough for field operations.

• Journal of Biosystems Engineering
• /
• v.29 no.5 s.106
• /
• pp.395-406
• /
• 2004

Most of tractors in the world have manual gear transmission, and some of small tractors have hydrostatic trans-mission(HST). Since the HST is expensive and has low power efficiency, it is being used for only small garden tractors. The continuously variable transmission(CVT) is an alternative to the HST or power-shift gear transmissions. The driver of the CVT tractor doesn't have to operate a shift lever since the CVT controller automatically controls the speed of tractor. Thus, it is much easier to operate the CVT tractor. For the easy and stable control of the CVT tractor, an appropriate control algorithm should be developed and the dynamic modeling should be carried out before making the prototype of CVT controller. This study was conducted to develop a simulation model of the CVT control system needed to develop a PID control algorithm. The simulation model consisted of variator dynamics, hydraulic system and control computer. And the simulation model was verified by experiment. The results obtained in this study can be utilized in the design of CVT tractors for practical use, but a lot of field tests and improvement of softwares would be necessary.

• Tribology and Lubricants
• /
• v.22 no.4
• /
• pp.196-202
• /
• 2006

This paper presents a case study on the tribological failure analysis of a clutch system for a manual transmission car. The clutch systems are composed of clutch disk, clutch pressure plate, flywheel rubbing surface, coil and diaphragm springs, release bearing and lever, clutch spline and shaft. The purpose of a clutch system is to transmit and disconnect the driving power of engines by frictional farce from a rubbing surface of a flywheel to a clutch disk and clutch pressure plate with a minimum power loss. In this study, many tribological failure cases based on the wear phenomena and thermal distortions have been presented, which are collected from the car repair shop and maintenance center. The triboiogicai failures are mostly come from the driving conditions, overloading of a car, and especially driving style and personal habit of a car driver.

• Korean Journal of Computational Design and Engineering
• /
• v.12 no.2
• /
• pp.109-117
• /
• 2007

Three-dimensional mesh models have been widely used in various applications such as simulations, animations, and e-catalogs. In such applications the normal vectors of mesh models are used mainly for shading and take up the major portion of data size and transmission time paper over networks. Therefore a variety of techniques have been developed to compress them efficiently. In this paper, we propose the MOEC (Modified Octree Encoding Compression) algorithm, which allow multi lever compression ratios for 3D mesh models. In the algorithm, a modified octree has nodes representing their own positions and supporting a depth of the tree so that the normal vectors are compressed up to levels where the shading is visually indistinguishable. This approach provides efficient in compressing normals with multi-level ratios, without additional encoding when changing in compression ratio is required.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1-4
• /
• 2003

Knowledge classification and expression of constructed knowledge have been main research issues in the field of knowledge representation. Constructed design knowledge of the former product loses its utility when new products with different structures are introduced to the market. In order to construct the design knowledge for a new product. designers need to reconstruct the design knowledge with new relationships. The design knowledge has been constructed with level trees, but it is difficult to rearrange the relations. Design DNA is proposed in this work in order to facilitate the rearrangement of design knowledge and give flexibility to knowledge structure. Design DNA is based on Layout-oriented domain knowledge and Function-oriented domain knowledge, which enables to generate new design knowledge that will result in new part geometries for given constraints on the part functions. Design DNA is applied to the design knowledge of lever system of the automatic transmission of passenger cars as an example.

• Journal of Biosystems Engineering
• /
• v.40 no.2
• /
• pp.95-101
• /
• 2015

Purpose: During the start-up period, the response time of a hydraulic system increases in the winter because of the increased oil viscosity caused by the cold weather. The problems of delayed tractor starting and excessive wear of the clutch disk occur for these reasons. Therefore, this study develops an analysis model using the commercial hydraulic analysis program AMESim to examine the characteristics of delays in power shuttle starting at different oil temperatures. Methods: In the experiment, a tractor was stationary on a flat surface with the engine running at a constant speed of 1,080 rpm. The forward lever was then pressed to activate the power shuttle at three different oil temperatures, and the pressure changes were measured. The pressure on the forward clutch control valve was measured by a pressure gauge installed on the hydraulic line supplied to the transmission from the main valve. An analysis model was also developed and verified with actual tests. Results: The trend of the simulated pressures of the power shuttle is similar to that of the measured pressures, and a constant modulation period was observed in both the simulation and test results. However, the difference found between the simulation and test results was the initial pressure required to overcome the initial force of the clutch spring. Conclusions: This study also examines the characteristics of the delayed startup of the power shuttle at different oil temperatures through simulations.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.1
• /
• pp.112-121
• /
• 2015

In this paper, powertrain of output split type plug-in hybrid electric vehicle is analyzed for the operation range of speed, torque, and power. First, it is assumed that the efficiency of motor is 100%. And, the speed and torque equations are derived based on the lever analogy. With the above equations, the simulations are performed for the powertrain of output split type plug-in hybrid electric vehicle. From the simulation results, it is found that the output torques of EV1 and series modes are larger than the EV2 and power split modes' ones. It means the EV1 and series modes can be used for the rapid acceleration. But the EV1 and series modes can be used only the velocity of under the 120 km/h. It is because the motor reaches its maximum speed when the velocity is over the 120 km/h for the EV1 and series modes. When the engine is turned on, the engine power is transmitted through the two motors. But, the power split mode shows the power split of engine at the output shaft, and it has the point of zero motor power. Thus, the transmission efficiency of the power split mode can be higher than the series mode's one, it the motor efficiency is considered.