• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.7
• /
• pp.17-25
• /
• 1999

Tungsten nitride($WN_x$) films were deposited by PECVD method on silicon nitride($WSi_3N_4$) substrate. The characteristics of $WN_x$ film were investigated with changing various processing parameters ; substrate temperature, gas flow rate, rf power, and different nitrogen sources. The nitrogen composition in $WN_x$ film varied from 0 to 45% according to the $NH_3$ and $N_2$ flow rate. The highest deposition rate of 160 nm/min was obtained for the $NH_3$ gas and relatively low deposition rate of $WN_x$ films were formed by $N_2$ gas. $WN_x$ films deposited on $WSi_3N_4$ substrate had higher deposition rate than that of TiN and Si substrates. The purity of $WN_x$ film were analyzed by AES and higher purity $WN_x$ films were deposited using $NH_3$ gas. The XRD analysis indicates a phase transition from polycrystalline tungsten(W) to amorphous tungsten nitride($WN_x$), showing improved etching profile of $WN_x$ films Thick $WN_x$ films were deposited on various substrates such as Tin, NiCr and Al and maximum thickness of $1.6 {\mu}m$ was obtained on the Al adhesion layer.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.37 no.1
• /
• pp.50-64
• /
• 2009

The freshwater lakes located at the fringe of urban cities are a habitat for diverse organisms. However, they are facing severe danger of environment deterioration and water pollution caused by reckless development of the area. In this study, an ecological management plan was suggested to promote the biodiversity through appointing management area based on the research and analysis data of flora and fauna as well as maintain biodiversity and harmonize utilization of freshwater lakes such as Duryang Reservoir at Sacheon, Gyeongsangnam-do. Base on the data of ecological research and analysis, this study conducted research on biotope assessment, wild life habitat assessment and presence of protected species. As a result, the ecosystem conservation area including multi-layer structured natural forests, waterside and wetland that are home to various species and the edge area with high habitat diversity were recognized as highly preservable regions. Management areas were ecologically disturbed region, highly polluted commercial district and damaged waterside caused by fishing. Proactive management must be implemented through vegetation management such as vegetation transition and shrub planting as well as establishing pollutant management system. The deterioration of waterside and forest vegetation of freshwater lake has a direct influence on biodiversity and water quality. Therefore, the conservation area and development area should be totally separated from each other, and the development area must be restored and managed strictly.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.46 no.2
• /
• pp.1-13
• /
• 2018

This work discusses the major roles of digital technologies in the history of landscape architectural drawing, and offers a critique of the dominant trend towards realism in recent digital landscape representations. During the period of transition from conventional drawing tools, computer technologies generally functioned as mechanical tools to imitate prior manual techniques. Specifically, the GIS was served as a mechanical tool to efficiently process the manual layer cake; CAD software generally functioned to translate physical models to two-dimensional construction documents while graphic software generally functioned as a tool to perform processes similar to those of manual collage and montage techniques. Recent digital landscape drawings tend to adopt a realistic depiction like the painting of landscape appearance. In the representations, discernible traces of cutting and assembling are removed via graphic software; thus, the complete representations are perceived as if they were a copy of an actual landscape. The realistic images are an easy way to communicate with the public. However, it is difficult to achieve a full embodiment of all of the multisensory characteristics of a landscape through these visuals. They often deceive viewers by visualizing idealized conditions of not-yet-actualized landscapes and production of the final images takes up a large portion of the overall design process. Alternatively, 3D digital modeling of landscape performance and creative uses of digital technologies during the overall design process, as well as hybridized techniques with different drawing techniques and technologies, provide the opportunity to explore various aspects of a landscape.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.181.2-181.2
• /
• 2014

A single-layer graphene has been uniformly grown on a Cu surface at elevated temperatures by thermally processing a poly (methyl methacrylate) (PMMA) film in a rapid thermal annealing (RTA) system under vacuum. The detailed chemistry of the transition from solid-state carbon to graphene on the catalytic Cu surface was investigated by performing in-situ residual gas analysis while PMMA/Cu-foil samples being heated, in conjunction with interrupted growth studies to reconstruct ex-situ the heating process. We found that the gas species of mass/charge (m/e) ratio of 15 ($CH_3{^+}$) was mainly originated from the thermal decomposition of PMMA, indicating that the formation of graphene occurs with hydrocarbon molecules vaporized from PMMA, such as methane and/or methyl radicals, as precursors rather than by the direct graphitization of solid-state carbon. We also found that the temperature for dominantly vaporizing hydrocarbon molecules from PMMA and the length of time, the gaseous hydrocarbon atmosphere is maintained, are dependent on both the heating temperature profile and the amount of a solid carbon feedstock. From those results, we strongly suggest that the heating rate and the amount of solid carbon are the dominant factors to determine the crystalline quality of the resulting graphene film. Under optimal growth conditions, the PMMA-derived graphene was found to have a carrier (hole) mobility as high as ${\sim}2,700cm^2V^{-1}s^{-1}$ at room temperature, which is superior to common graphene converted from solid carbon.

• Economic and Environmental Geology
• /
• v.43 no.4
• /
• pp.371-379
• /
• 2010

Fresh water injection test in a fractured bedrock aquifer was applied as an efficient approach to lower saline concentrations in the saltwater-freshwater transition zone formed by seawater intrusion in a coastal area. The methodology and effectiveness of fresh water injection for hydraulically controlling seawater intrusion is overwhelmingly site dependent, and there is an urgent need to characterize the permeable fractures or unconsolidated porous formations which can allow for seawater flow and transport. Considering aquifer characteristics, injection and monitoring boreholes were optimally designed and completed to inject fresh water through sand layer and fractured bedrock, respectively. We devised and used the injection system using double packer for easy field operation and maintenance. Overall fracture distribution was systematically identified from borehole image logs, and the section of fresh water injection was decided from injection test and monitoring. With fresh water injection, the fluid electrical conductivity of the monitoring well started to be lowered by the inflow of fresh water at the specific depth. And this inflow leaded to the replacement of the fluid in the upper parts of the borehole with fresh water. Furthermore, the injection effect lasted more than several months, which means that fresh water injection may contribute to the mitigation of seawater intrusion in a coastal area.

• Applied Chemistry for Engineering
• /
• v.8 no.6
• /
• pp.1041-1047
• /
• 1997

The influence of $\omega$-phenylalkylammonium salt on the critical micelle concentration (CMC) of SDS has been examined using the electric conductivity method. CMC of SDS exhibited the tendency to decrease with the length of alkyl group of additives. The effect of temperature on CMC of SDS in additive solutions has been observed in the range of $18^{\circ}C-50^{\circ}C$. The free energy(${\Delta}G_m^{\circ}$) for the micellization of SDS is negative and the entropy(${\Delta}S_m^{\circ}$) is a large positive value. The enthalpy(ΔHm0is positive in low temperature($18^{\circ}C$) and negative in high temperature($>25^{\circ}C$). In the prensence of organic additives, the micellization of SDS was considered as a spontaneous process and to involve a phase transition. The values of ΔGm0has shown the tendency to increase but the values of ${\Delta}S_m^{\circ}$ and ${\Delta}H_m^{\circ}$ to decrease with the length of alklyl group of additive salts. The changes in ${\Delta}\kappa$(difference of specific conductivity) with increasing mole ratio of additives in the mixed solutions indicated the formation of mixed micelles between SDS and additives. The effect of the length of alkyl chain on the micellization of SDS demonstrated the penetration of organic additives into the palisade layer of the SDS micelle.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.4
• /
• pp.545-553
• /
• 2003

To achieve good dentin bonding, we must obtain proper wet dentin surface. The purpose of this study was to compare dentin surface according to different wetness degree by AFM image as studying how to obtaining proper wet dentin surface. Intact recently extracted primary teeth were used in the study. The extracted teeth were stored in distilled water at $4^{\circ}C$ until prepared. The teeth were used to prepare 1mm thick dentin disks with exposed surfaces parallel to the occlusal surfaces. The surface of the dentin were polished with polishing disk. The sample were ultrasonically cleaned with distilled water. The sample of each group were treated by different ways. We compared dentin surface of each group by AFM image. From the experiment, the following results were obtained. 1. Acid etching in the dentin surface of primary teeth, resulted in the removal of the smear layer, which opened dentinal tubules, caused the demineralization of peritubular and intertubular dentin, and exposed a collagen-rich transition zone. 2. If the etched dentin was so dehydrated, the intertubular dentin surfaces deceased in height and the diameters of the dentinal tubules decreased slightly. 3. In the group dried with compressed air for 20 seconds at 2 cm, the dentin surfaces were too excessive dried and dehydrated. 4. In the group dried with compressed air for 3 seconds at 2 cm, dry cotton, wet cotton, microbrush and absorbent tissue paper, the dentin surfaces were properly wet.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.10a
• /
• pp.15-15
• /
• 2003

치과재료에 사용되는 금속재료는 주로 스테인리스강, 타이타늄, Ni-Ti, Co-Cr등과 같은 특수합금이 주로 사용되고 있다. 이들 재료는 치과 보철물과 교정재료 및 충전재료로 주로 사용되고 있으며 그 외 치과에서 사용되는 기기나 기구에도 많이 활용되고 있다. 특히 치과 보철물을 사용하여 치료를 원하는 환자가 최근에 급격히 증가하면서 임플란트 고정체와 나사 등을 이용한 치료법의 연구와 개발이 필요하게 되어 세계적으로 연구와 투자가 활발히 진행되고 있다. 그러나 재료의 설계나 합금의 설계 및 제품의 설계상의 문제로 인하여 생체조직과 결합하는데 많은 문제점이 임상적으로 발생되고 있다. 즉 임플란트 표면의 생체적합성부여, 고정체와의 결합시 파절이나 풀림현상, 골에 고정체로 사용하는 나사의 강도와 내마모성문제 등이 개선되어야 할 문제점으로 남아있다. 또한 총의치에 사용되는 자석 어태치먼트의erosion-corrosion문제, 교정선의 탄성 과 마모저항문제 등은 앞으로 계속적인 연구를 행하여야할 과제로 남아있다. 또한 국소의치에서 사용되는 frame은 정밀주조법을 통하여 제조하며 주조상의 결함 등으로 인한 클라스프의 파절 문제점이 발생되고 있다. 따라서 본 연구에서는 치과재료로 사용되는 임플란트 고정체, 나사, 교정용 선등의 문제점을 고찰하고, 지금까지 이루어진 연구를 중심으로 최적의 개선 조건을 찾고자하였다. 최근첨단소재 및 금속재료를 사용하여 치과재료 합금을 설계할 수 있는 연구가 활발히 진행된다면 수입에 의존하고 있는 고가의 치과재료를 값이 싼 고성능의 제품으로 대체할 수 있는 효과가 클 것으로 생각된다.>$\rho$$\sub$0/=1.8 %. As t$\sub$Co/ increases, a transition from the regime of co-existence of superparamagnetic and ferromagnetic behaviors to ferromagnetic behavior was observed. Tunneling barrier called "decay length for tunneling" for the films having the thickness of Co layer from 1.4 to 1.6 nm was measured to be ranged from 0.004 to 0.021 ${\AA}$$\^$-1/.문에 기업간 관계를 연구하는 측면에서는 탐험적 연구성격이 강하다. 더 나아가 본 산업의 주된 연구가 질적이고 기업내부만을 연구했던 것에 비교하면 시초적이라고 할 수 있다. 또한 관계마케팅, CRM 등의 이론적 배경이 되고 있는 신뢰와 결속의 중요성이 재확인하는 결과도 의의라고 할 수 있다. 그리고 신뢰는 양사 간의 상호관계에서 조성될 수 있는 특성을 가진 반면, 결속은 계약관계 초기단계에서 성문화하고 규정화 할 수 있는 변수의 성격이 강하다고 할 수가 있다. 본 연구는 복잡한 기업간 관계를 지나치게 협력적 측면에서만 규명했기 때문에 많은 측면을 간과할 가능성이 있다. 또한 방법론적으로 일방향의 시각만을 고려했고, 횡단적 조사를 통하고 국내의 한 서비스제공업체와 관련이 있는 컨텐츠 공급파트너

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.41-41
• /
• 2007

For use in spintronic materials, dilute magnetic semiconductors (DMS) are under consideration as spin injectors for spintronic devices[l]. $TiO_2$-based DMS doped by a cobalt, iron, and manganese et al. was recently reported to show ferromagnetic properties, even at temperatures above 300K and the magnetic ordering was explained in terms of carrier-induced ferromagnetism, as observed for a III-V based DMS. An anomalous Hall effect (AHE) and co-occurance of superparamagnetism in reduced Co-doped rutile $TiO_{2-\delta}$ films have also been reported[2]. Metal segregation in the reduced metal-doped rutile $TiO_2-\delta$ films still remains as problems to solve the intrinsic DMS properties. Superlattice films have been proposed to get dilute magnetic semiconductor (DMS) with intrinsicroom-temperature ferromagnetism. For a $TiO_2$-based DMS superlattice structure, each layer was alternately doped by two different transition metals (Fe and Mn) and deposited to a thickness of approximately $2.7\;{\AA}$ on r-$Al_2O_3$(1102) substrates by pulsed laser deposition. The r-$Al_2O_3$(1102) substrates with atomic steps and terrace surface were obtained by thermal annealing. Samples of $Ti_{0.94}Fe_{0.06}O_2$(TiFeO), $Ti_{0.94}Mn_{0.06}O_2$(TiMnO), and $Ti_{0.94}(Fe_{0.03}Mn_{0.03})O_2$ show a low remanent magnetization and coercive field, as well as superparamagnetic features at room temperature. On the other hand, superlattice films (TiFeO/TiMnO) show a high remanent magnetization and coercive field. An anomalous Hall effect in superlattice films exhibits hysisteresis loops with coercivities corresponding to those in the ferromagnetic Hysteresis loops. The superlattice films composed of alternating layers of $Ti_{0.94}Fe_{0.06}O_2$ and $Ti_{0.94}Mn_{0.06}O_2$ exhibit intrinsic ferromagnetic properties for dilute magnetic semiconductor applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.493-496
• /
• 2005

비정질 실리콘 (a-Si)의 수소화를 통해 활성화 수소가 비정질 실리콘내의 댕글링본드 (dangling bond) 와 결합 하므로 에너지밴드의 국재준위(localized state)를 감소시켜 불순물 도핑이 가능하게 되므로 a-Si 이 전자소자로서 이용 가능하게 되었다. 이에 착안하여 본 연구에서는 경사($0^{\circ}$, $45^{\circ}$, $80^{\circ}$) 증착을 통해 비정질 칼코게나이드($a-As_{40}Ge_{10}Se_{15}S_{35}$) 박막을 제작하고 그 박막을 수소화처리 (15~20atm at $150\sim190^{\circ}C$)하여 처리 전 후의 surface morphology 변화 및 광학적 특성 변화를 고찰하였다. $a-As_{40}Ge_{10}Se_{15}S_{35}$ 박막의 SEM 측정을 통해 $40^{\circ}$와 $80^{\circ}$ 경사 증착된 $a-As_{40}Ge_{10}Se_{15}S_{35}$ 박막에서 각각 18.8nm 와 160nm의 transition layer와 박막의 기둥(columnar)구조가 형성됨을 관찰하였다. 특히, $80^{\circ}$ 증착박막의 경우 수소처리전 columnar구조는 약 $65\sim70^{\circ}$의 기둥 각을 가지고 형성되었고 수소화 처리를 통해 기둥구조가 붕괴 되었다. $70^{\circ}$ 경사 증착된 $a-As_{40}Ge_{10}Se_{15}S_{35}$ 박막은 $0^{\circ}$에 따른 박막 보다 흡수단 부근에서 약 20%의 투과도 증가와 광 에너지 갭 ($E_{op}$)의 증가를 관찰 할 수 있었다. $80^{\circ}$경사 증착된 수소처리 박막에서 흡수단 부근의 투과도가 약 10%증가 되었고, 광 에너지 갭은 약 0.07eV 증가 하였고, PL intensity는 흡수단 부근에서 증가한 것을 확인 할 수 있었다. 이러한 변화들은 경사 증착된 $a-As_{40}Ge_{10}Se_{15}S_{35}$ 박막 내의 상대적으로 원자 밀도가 큰 기둥(columnar)구조가 생성되고, 이 원자 밀도가 높은 기둥구조의 댕글링본드와 주입된 수소가 흡착하여 에너지대의 국재준위를 감소시키기 때문으로 판단된다.