• Journal of the Korean Magnetics Society
• /
• v.7 no.4
• /
• pp.173-179
• /
• 1997

Change in phases, microstructures, and magnetic properties by the variation of quench rate and heat treatment were investigated for melt-spun $Fe_{77}Pr_{15}C_8$ ribbons. The amorphization of as-spun ribbons increased as the quench rate increased. As a result, the ribbon quenched at 40 m/s was almost entirely amorphous. Similarly to cast alloys, the primary phase in crystalline ribbons quenched at 10 m/s was $\alpha$-Fe followed by the secondary $Fe_{17}Pr_2C_x$. Crystalline phases were still dominant in the ribbon spun at 20 m/s, but in this case crystallization of $Fe_{17}Pr_2C_x$ was remarkable with a little suppression of $\alpha$-Fe. At 30 m/s an amorphous phase obviously dominated in the as-spun ribbons with small fraction of crystals. Therefore, substantial amount of hard magnetic $Fe_{14}Pr_2C$ was not obtained from the as-spun state but, as in cast alloys, produced only by a solid-state transformation. Within a few minutes fine grains of $Fe_{14}Pr_2C$ were easily obtained at relatively low temperature when the degree of amorphization of as-spun ribbons was higher. The grain size of $Fe_{14}Pr_2C$ was well less than 1${\mu}{\textrm}{m}$. The ribbons quenched at 20 or 30 m/s yielded higher coercivities after heat treatment.

• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.3 no.1
• /
• pp.32-43
• /
• 1995

Ni-Ti alloy has excellent corrosion resistance, biocompatibility, shape memory effect and superelasticity, so it has been used widely in biomedical fields. But it has difficulty in casting due to its high melting temperature and oxygen affinity at high temperature. Recently it has been attempted to cast Ni-Ti alloy using new casting machine and investment. The purpose of this study was to examine the superelastic behavior of cast shape memory Ni-Ti alloy and to compare the mechanical properties of the cast shape memory alloy with those of commercial alloys for removable partial denture framework. Ni-Ti alloy(Ni 50.25%, Ti 49.75% : atomic ratio) was cast with dental argon-arc pressure casting machine and Type IV gold alloy, Co-Cr alloy, Ni-Cr alloy, pure titanium were cast as reference. Experimental cast Ni-Ti alloy was treated with heat($500{\pm}2^{\circ}C$) in muffle furnace for 1 hour. Transformation temperature range of cast Ni-Ti alloy was measured with differential scanning calorimetry. The superelastic behavior and mechanical properties of cat Ni-Ti alloy were observed and evaluated by three point bending test, ultimate tensile test, Vickers microhardness test and scanning electron microscope. The results were as follows : 1. Cast Ni-Ti alloy(Ni 50.25%, Ti 49.75% : atomic ratio) was found to have superelastic behavior. 2. Stiffness of cast Ni-Ti alloy was considerably lesser than that of commercial alloys for removable partial denture. 3. Permanent deformation was observed in commercial alloys for removable partial denture framework at three point bending test over proportional limit(1.5mm deflection), but was not nearly observed in cast Ni-Ti alloy. 4. On the mechanical properties of ultimate tensile strength, elongation and Vickers microhardness number, cast Ni-Ti alloy was similiar to Type IV gold alloy, Co-Cr alloy, Ni-Cr alloy and pure titanium. With these results, cast Ni-Ti alloy had superelastic behavior and low stiffness. Therefore, it is suggested that cast Ni-Ti alloy may be applicated to base metal alloy for removable partial denture framework.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.247-256
• /
• 2000

Precursor gels with the composition of $xZrO_2{\cdot}(100-x)SiO_2$ systems (x=10, 20 and 30 mol%) were prepared by the sol-gel method. Kinetic parameters, such as activation energy, Avrami's exponent, n, and dimensionality crystal growth value, m, have been simultaneously calculated from the DTA data using Kissinger and Matusita equations. The crystallite size dependence on tetragonal to monoclinic transformation of $ZrO_2$ was investigated using XRD, in relation to the fracture toughness. The crystallization of tetragonal $ZrO_2$ occurred through 3-dimensional diffusion controlled growth(n=m=2) and the activation energy for crystallization was calculated using Kissinger and Matusita equations, as about $310{\sim}325{\pm}10kJ/mol$. The growth of $t-ZrO_2$, in proportion to the cube of radius, increased with increasing heating temperature and heat-treatment time. It was suggested that the diffusion of Zr4+ions by Ostwald ripening was rate-limiting process for the growth of $t-ZrO_2$ crystallite size. The fracture toughness of $xZrO_2{\cdot}(100-x)SiO_2$ systems glass ceramics increased with increasing crystallite size of $t-ZrO_2$. The fracture toughness of $30ZrO_2{\cdot}70SiO_2$ system glass ceramics heated at $1,100^{\circ}C$ for 5 h was $4.84Mpam^{1/2}$ at a critical crystaliite size of 40 nm.

• Journal of Powder Materials
• /
• v.25 no.3
• /
• pp.246-250
• /
• 2018

In this study, we investigate the deformation behavior of $Hf_{44.5}Cu_{27}Ni_{13.5}Nb_5Al_{10}$ metallic glass powder under repeated compressive strain during mechanical milling. High-density (11.0 g/cc) Hf-based metallic glass powders are prepared using a gas atomization process. The relationship between the mechanical alloying time and microstructural change under phase transformation is evaluated for crystallization of the amorphous phase. Planetary mechanical milling is performed for 0, 40, or 90 h at 100 rpm. The amorphous structure of the Hf-based metallic glass powders during mechanical milling is analyzed using differential scanning calorimetry (DSC) and X-ray diffraction (XRD). Microstructural analysis of the Hf-based metallic glass powder deformed using mechanical milling reveals a layered structure with vein patterns at the fracture surface, which is observed in the fracture of bulk metallic glasses. We also study the crystallization behavior and the phase and microstructure transformations under isothermal heat treatment of the Hf-based metallic glass.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.634-639
• /
• 1998

$Y_2O_3$ and $Nb_2O_5$ co-doped zirconia composites containing 10~30 vol% $Al_2O_3$ with two different particle sizes were sintered for 5 h at $1550^{\circ}C$ to evaluate low-temperature phase stability of the composite using X-ray diffractometry after heat-treatments for 1000 h at $250^{\circ}C$ in air or for 5 h at $180^{\circ}C$ in 0.3 MPa $H_2O$ vapor pressure. No tetragonal to monoclinic phase transformation during degradation, so called enhanced low-temperature phase stability, was observed for all composites. It is concluded that Nb addition to the composite for the phase stability is more effective than $Al_2O_3$ addition. The optimum combination of strength (670 MPa) and fracture toughness ($7.1{\textrm} {MPam}^{1/2}$) were obtained for the composite containing 20 vol% of $Al_2O_3$ with 2.8 $\mu$m to 0.2 $\mu$m, the flexural strength increases but the fracture toughness decreases.

• Journal of Welding and Joining
• /
• v.34 no.1
• /
• pp.75-81
• /
• 2016

This study applied laser surface melting process using CW(Continuous wave) Yb:YAG laser and cold-work die steel SM45C and investigated microstructure and hardness. Laser beam speed, power and beam interval are fixed at 70 mm/sec, 2.8 kW and $800{\mu}m$ respectively. Depth of Hardening layer(Melting zone) was a minimum of 0.8 mm and a maximum of 1.0 mm that exceeds the limit of minimum depth 0.5 mm applying trimming die. In all weld zone, macrostructure was dendrite structure. At the dendrite boundary, Mn, Al, S and O was segregated and MnS and Al oxide existed. However, this inclusion didn't observe in the heat-affected zone (HAZ). As a result of interpreting phase transformation of binary diagram, MnS crystallizes from liquid. Also, it estimated that Al oxide forms by reacting with oxygen in the atmosphere. The hardness of the melting zone was from 650 Hv to 660 Hv regardless of the location that higher 60 Hv than the hardness of the HAZ that had maximum 600 Hv. In comparison with the size of microstructure using electron backscatter diffraction(EBSD), the size of microstructure in the melting zone was smaller than HAZ. Because it estimated that cooling rate of laser surface melting process is faster than water quenching.

• Korean Journal of Oriental Medicine
• /
• v.13 no.2 s.20
• /
• pp.59-63
• /
• 2007

The purpose of this study was to diagnosis that what patterns identification using the statistical method. Discriminant analysis using the medical specialist and resident pattern identification agree case in stroke patients within 1 month of onset. The agreement rate of dificiency of Gi(75%), heat-transformation(74%), dampphlegm syndrome(69%), deficiency of Eum(51%) and syndrome of blood stagnation(43%) are respectively 0.75, 0.74, 0.69, 0.51 and 0.43 in medical specialist and using linear discriminant function pattern identification are same. The study of inspection, pulse feeling and palpitation will be continued to evaluate concordance rate. Discrimination model will be make to get higher Accuracy and prediction, it means becomes the help in pattern identification diagnosis objectivity and scientific.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.2
• /
• pp.120-126
• /
• 2010

This paper propose analysis and examination of the melting characteristic of fuse elements by repeating overcurrent as a depletion factor of high pressure current limiting fuse through test following existence and nonexistence of extinction material and various configuration of elements. To examine deterioration progress rate by repeating overcurrent we analyzed heat for various element notching configuration, designed plate type, ring type element and estimated the relationship with life span by analyzing breaking characteristic through repeating overcurrent test with adjusting load factor at Silicon Dioxide(SiO2) filled state or in air. A Crack by repeat stress, decrease of section and transformation by friction with extinction material by repeating overcurrent causes a problem which shortens life span based on fuse repeating frequency. Since the contents of this paper might be useful to research the correlation between friction of materials and repeating life span based on load factor of repeating current, the quality of product would be improved through solution of the problem.

• Journal of the Korean Institute of Gas
• /
• v.24 no.5
• /
• pp.39-46
• /
• 2020

This paper is considered about centerline segregation of API 5L steel used in pipeline. Mn/S, Nb and C were known as segregated elements in the centerline of pipe thickness. The Mn usually was accompanied by S consisting of long viscous shape. Microstructure of the centerline was composed of MnS and Nb/Ti indusions including oxide. The segregation effect in centerline region was analyzed by OM, SEM/EDS and micro Vickers hardness. The Mn, Nb and C are retarded elements in transformation from austenite to ferrite or martensite. These elements could derive a bainitic microstructure as a kind of martensite, which is different from difference and element segregation between in matrix and centerline derived from steel melting and heat treatment.

• Journal of Microbiology and Biotechnology
• /
• v.8 no.6
• /
• pp.560-567
• /
• 1998

We have found that Thermoactinomyces vulgaris KFB-Cl00 produces a chitinase. The optimum temperature and pH of the enzyme activity were $55^{\circ}C$ and 6.5. The enzyme was stable after heat treatment at $80^{\circ}C$ for 30 min and stable in acidic and basic conditions (PH 6.0~11.0). The thermostable endo-chitinase from Thermoactinomyces vulgaris KFB-C100 was cloned into the plasmid pBR322 by using E. coli DH5$\alpha$ as a host strain. The positive clone carrying a recombinant plasmid (PKCHI23) with a 4.1-kb fragment containing the chitinase gene was found. The recombinant plasmid was analyzed to determine the essential region for chitinase activity and obtained a 2.3-kb fragment, which was sub cloned into pTrc99A using the PstI and SalI sites to construct pTrc99A/pKCHI23-3. The resulting plasmid exerted high chitinase activity upon transformation of E. coli XL1-Blue cells. Chitinase was overproduced 14 times more in the clone cells than in the wild-type cells and the enzyme was purified to homogeneity. The purified enzyme showed the similar properties as the native chitinase from T. vulgaris in terms of molecular weight and substrate specificity. The catalytic action of the cloned enzyme was an endo type, producing chitobiose as a major reaction product.