• Journal of Korean Society of Steel Construction
• /
• v.9 no.3 s.32
• /
• pp.431-440
• /
• 1997

The paper describes a theoretical model for the prediction of bridge temperatures from meteorological data measured at bridge site and local meteorological center together with existing finite element heat transfer theory and solar radiation transfer theory to determine the time dependent temperature distribution of bridge. In this analytical model, the most adequate equation for the calculation of solar radiation on the bridge surface, which is dominant in day time is described based on the results of several experimental studies for the solar energy. The validity of this model is tested against field data obtained from long term experimental program on Sadang Viaduct in Seoul. Also, this paper describes the linear correlation between design variables and meteorological data to establish analytical criteria for the prediction of the average temperature, which are responsible for the longitudinal deformation of the bridges and of the vertical differential temperature profiles. which are responsible for the bending deformations from the long term experimental results.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.4
• /
• pp.387-399
• /
• 2003

The box system that consists only of reinforced concrete walls and slabs we adopted in many high-rise apartment buildings recently constructed in Korea. Recently, many of the box system buildings with pilotis has been constructed to meet the architectural design requirements. This structure has abrupt change in the structural properties between the upper and lower parts divided by transfer girders. For an accurate analysis of a structure with pilotis, it is necessary to have the buildings modeled into a finer mesh. But it would cost tremendous amount of computational time and memory. In this study, an efficient method is proposed for an efficient analysis of buildings those have pilotis with drastically reduced time and memory. In the proposed analysis method, transfer gilders are modeled using super elements developed by the matrix condensation technique and fictitious beams are introduced to enforce the compatibility conditions at the boundary of each element. The analyses of example structures demonstrated that the proposed method used for the analysis of a structure with pilotis will provide analysis results with accuracy for the design of box system buildings.

• Wind and Structures
• /
• v.37 no.6
• /
• pp.399-412
• /
• 2023

Previous studies have shown that the integrated transfer function (ITF) is independent of turbulence characteristics and can be effectively applied to predict the buffeting response of elongated structures, assuming that the strip hypothesis is valid. However, existing research has not effectively identified the ITF through segment model vibration tests, and the influence of the 3D effect on the accuracy of the strip hypothesis and the characteristics of the ITF in wind tunnel tests has not been quantitatively studied. A segment model vibration measurement device that can change a test model's span-width ratio was designed in this study. An airfoil section and a streamlined box girder section structure were taken as the background, and their ITFs were effectively identified under different L/B (L denotes the turbulent integral scale and B denotes the structural width) and model span-width ratios. The influence laws of the 3D effect on the accuracy of the strip hypothesis and ITF identification in wind tunnel tests were systematically investigated. The results showed that L/B and the structural span-width ratio are two significant controlling factors that affect the accuracy of the strip hypothesis and ITF identification. The research provides an effective experimental method for accurately predicting the buffeting response of elongated structures based on ITFs identified through segment model vibration tests.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.6
• /
• pp.1299-1308
• /
• 1994

This paper is considered on the dynamic behavior and the dynamic impact coefficient on the cable-stayed bridge under the vehicle load. The method of static analysis, that is, the transfer matrix method is used to get influence values about displacements, section forces of girder and cable forces. Gotten influence values were used as basic data to analyse dynamic behavior. This paper used the transfer matrix method because it is relatively simpler than the finite element method, and calculating speed of computer is very fast and the precision of computation is high. In the process of dynamic analysis, the uncoupled equation of motion is derived from simultaneous equation of the motion of cable-stayed bridge and vehicle travelling by using mode shape, which was borne from system of undamped free vibration. The solution of the uncoupled equation of motion, that is, time history of response of deflections, velocity and acceleration on reference coordinate system, is found by Newmark-${\beta}$ method, a kind of direct integral method. After the time history of dynamic response was gotten, and it was transfered to the time history of dynamic response of cable-stayed bridge by linear transformation of coordinates. As a result of this numerical analysis, effect of dynamic behavior for cable-stayed bridge under the vehicle load has varied depending on parameter of design, that is, the ratio of span, the ratio of main span length, tower height, the flexural rigidity of longitudinal girder, the flexural rigidity of tower, and the cable stiffness, investigated. Very good agreements with the existing solution in the literature are shown for the uncracked plate as well as the cracked plate.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.1
• /
• pp.57-64
• /
• 2022

This study investigated the structural performance of the RC boundary beam-wall system subjected to axial loads that required lesser construction quantity and smaller floor height in comparison with the conventional RC transfer girder system. Four specimens of 1/2 scale were constructed, and their peak strengths under axial loads and failure characteristics were compared and analyzed. Test parameters included the ratio of the lower to the upper wall length, lower wall thickness, and stirrup details of the lower wall. In addition, three-dimensional nonlinear finite element analysis was performed to verify the effectiveness of the boundary beam-wall system. The peak strength of each specimen was similar to the nominal axial strength of the lower wall, indicating that the axial load was transferred smoothly from the upper to the lower wall. The contribution of the lower wall cross-section was high if the ratio of the lower to the upper wall length was small; the contribution was low if the out-of-plane eccentricity existed in the lower wall. The specimen with smaller stirrup distance and cross-ties in the lower wall showed higher initial stiffness and peak load than other specimens.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.3
• /
• pp.441-451
• /
• 2002

Recently, Increasing residential-commercial buildings are composed of upper wall and lower frame type. As structural fragility, a large numbers of researchers have tried to develope the efficient analysis methods. But these studies were too theoretical and were not considered the lateral load which was required in analysing the transfer level in addition to being used nonlinear program which was difficult to use for practical design. thus, results of these studies we not appropriate to apply practical design, therefore, in this paper, the procedure of the current design practice were compared with that of used FEM method and presented new modeling method. in particular, an efficient analytical model which can be used in practical design of residential-commercial buildings for vortical and seismic loads was proposed and the usefulness of proposed model was verified.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.21 no.6
• /
• pp.287-293
• /
• 2017

Sometimes, it is impossible to install a sensor on a certain location of a structure due to the size of a structure or poor surrounding environments. Even if possible, sensors can be frequently malfunctioned or improperly operated due to lack of adequate maintenance. These kind of problems are solved by the virtual sensing methods in various engineering fields. Virtual sensing technology is a technology that can measure data even though there is no physical sensor. It is expected that this technology can be also applied to the construction field effectively. In this study, a virtual sensing technology based on ARX model is proposed. An ARX model is defined by using the simulated data through a structural analysis rather than by actually measured data. The ARX-based virtual sensing model can be applied to estimate unmeasured response using a transfer function that defines the relationship between two point data. In this study, a simulation and experimental study were carried out to examine the proposed virtual sensing method with a laboratory test on a cable-stayed model bridge. Acceleration measured at a girder is transformed to estimate a cable tension through the ARX model-based virtual sensing.

• Composites Research
• /
• v.24 no.5
• /
• pp.29-33
• /
• 2011

The application of high performance materials for the deck can represent a fair alternative to reduce the weight of the deck and improve the econimic efficiency of the bridge even if high performance materials are costly. In UHPC(Ultra High Performance Concrete) bridges, it is necessary to verify that exiting headed stud can be used to transfer longitudinal shear forces across the steel-concrete interface. In this paper, the push-out tests are performed to analisys the composite behavior between UHPC bridge deck and steel girder. The ultimate strength of test specimens is proportional to the diameter of headed studs in push-out test for static loading. Test results show that the shear strength of headed stud is improved for the case of normal concrete bridge decks.

• Smart Structures and Systems
• /
• v.23 no.4
• /
• pp.359-371
• /
• 2019

As part of a structural health monitoring system, the relative geometric relationship between a ship and bridge has been recognized as important for bridge authorities and ship owners to avoid ship-bridge collision. This study proposes a novel computer vision method for the real-time geometric parameter identification of moving ships based on a single shot multibox detector (SSD) by using transfer learning techniques and monocular vision. The identification framework consists of ship detection (coarse scale) and geometric parameter calculation (fine scale) modules. For the ship detection, the SSD, which is a deep learning algorithm, was employed and fine-tuned by ship image samples downloaded from the Internet to obtain the rectangle regions of interest in the coarse scale. Subsequently, for the geometric parameter calculation, an accurate ship contour is created using morphological operations within the saturation channel in hue, saturation, and value color space. Furthermore, a local coordinate system was constructed using projective geometry transformation to calculate the geometric parameters of ships, such as width, length, height, localization, and velocity. The application of the proposed method to in situ video images, obtained from cameras set on the girder of the Wuhan Yangtze River Bridge above the shipping channel, confirmed the efficiency, accuracy, and effectiveness of the proposed method.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.35 no.10
• /
• pp.63-70
• /
• 2019

The Busan branch of the former Toyo Takushoku Co. carried out the same business as a bank at the time of construction. This required an open space of long-span, which had no pillars, on the first floor where many customers frequently visited. In addition, an office space is required in the upper part, and a column is arranged so as to place a corridor in the center. It was designed with modern complex structures for space utilization and structural adaptation. As a result, scientific structural calculations of the modern era began and various structural technologies were introduced, the rationalization and value of various spatial characteristics and their structural design were analyzed from a technical historical perspective in the structure requiring long-span space. The Busan branch of the former Toyo Takushoku Co. is a complex structure with three structures. It is highly valuable as a building that tried to design its structure in a variety of spaces through calculation and introduction of new technology based on the principle of force in modern times.