• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.15 no.1
• /
• pp.5-16
• /
• 1979

At the holding of live anchovies which will be used as bait for the skipjack fishing, it is necessary to transrer the holding creel to the holding ground from the long distanted fishing ground. Usually, the creel made with net webbing and shaped like pound, was towed with a tow rope fastened to the front fringe or it, when two serious problems were found. The one was that the leading flap or the webbing of creel was drifted backward by the drag and caused to decrease the volume of the creel and made anchovies mortal. The other was that much time were spent to tow creels for long distance with slow speed, whereas to tow fast made anchovies worn out and caused them mortal. To prevent these defect, the authors carried out a model experiment in a circular flowing tank with a 1/15 scale model creel by four different arrangement of towing, and found out two suitable method, then these two methods were experimented in the sea with full rigged creel, and found the most suitable method out. To decrease the interior current speed of the creel even if it was towed fast, the apron which made by the same webbing of the creel body was enclosed the leading flap of creel, when the interior current speed showed the 35 to 40 percent of towing speed, whereas it showed 50 to 55 percent without apron.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.4
• /
• pp.266-277
• /
• 1991

To catch the surf clam, Mactra chinensis, in sand bottom using the excavating performance of water jet, the authors had constructed the experimental hydraulic jet dredge by the result of water tank experiment of previous report, and also were carried out the field experiments in the surf clam fishing ground near Kunsan, Korea from 5th to 30th of October, 1990. The results obtained are as follows. 1) Excavating depth was more than 10~11cm at the 1500cm/s water-jet velocity in the fine sand and muddy sand. 2) Towing tention was only 105$\pm$5kg in the 6.7cm/s towing speed. 3) Average catch amount per unit towing area was 0.42kg/m super(2) and it was 1.2~1.6 times comparing on the conventional dredge. 4) Experimental hydraulic jet dredge did not nearly brake the surf clam. 5) Turbidity variation by the water jet of dredge was not serious in the fishing ground; On the surface, when the depth is more than 5.2m, turbidity variation was not found at all, and on the 3m layer above the bottom, turbidity variations was increased 9~11ppm at 1m backward from the dredge, but it was gradually decrease, and it was nearly not at 9m backward from the dredge.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.2 no.1
• /
• pp.40-48
• /
• 1999

Wave absorbing system is needed at various kinds of wave basins (wave flume, towing tank, square tank) for the model test related to the ocean engineering. In this paper, the performance of wave absorbing system with new concept is estimated throughout the experiments. Herein, the wave absorbing system is designed by punching plate with a given porosity which is installed horizontally and submerged near the water surface. As the incident wave generated by a wave maker advances above a punching plate, the strong jet flow is formed near a hole of punching plate. As a result, wave energy is dissipated into heat energy, Systematic model tests were conducted at KRISO to verify the performance of the wave absorber using a punching plate. It was found that the reflection coefficient of wave absorber is deeply dependent on both the porosity and the submerged depth of a punching plate. Inclined installation of a punching plate shows better performance than a horizontal one within a certain inclined angle.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.478-483
• /
• 2001

We experimentally attempted to understand the vibration characteristics of a flexible pipe excited by vortex shedding. This has been extensively studied in the past decades (For example, see ［2-9］). However, there are still areas that need more study. One of them is to study the relation between spatial characteristics of a flow induced vibrating pipe, such as its length, the distribution of wave number, and frequency responses. A non-linear mechanism between the responses of in-line and cross-flow directions is also an area of interests, if the pipe is relatively long so that structural modal density is reasonably high. In order to investigate such areas, two kinds of instrumented pipe were designed. The instrumented pipes, of which the lengths are equally 6m, are wound with rubber and silicon tape in different ways, having different vortex shedding conditions. One has uniform cross-section of diameter of 26. 7mm, and the other has equally spaced by 4 sub-sections, which are composed of different diameters of 75.9, 61.1, 45.6 and 26.7mm. Both pipes are towed in a water tank (200m ${\times}$ 16m ${\times}$ 7m) so that they experienced different vortex shedding excitations. The towing pipe experiments exhibit several valuable features. One of them is that the natural frequencies and their corresponding strain mode shapes dominate the strain response of the uniform pipe. However, for those of non-uniform pipe, the responses are more likely local and many modes participate in it.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.3
• /
• pp.64-70
• /
• 2008

A full-scale field experiment is an important part in the design of ships and offshore structures. Full-scale tests in the ice-covered sea, however, are usually very expensive and difficult tasks. Model tests in a refrigerated ice tank may substitute this difficulty of full-scale field tests. One of the major tasks to perform proper model tests in an ice towing tank is to select a realistic material for model ice which shows correct similitude with natural sea ice. This study focuses on the testing material properties and the selection of model ice material which will be used in an ice model basin. The first Korean ice model basin will be constructed at the Maritime & Ocean Engineering Research Institute (MOERI) in 2009. With an application to the MOERI ice model basin, in this study the material properties of EG/AD/S model ice of IOT (Institute for Ocean Technology) Canada, were tested. Through comprehensive bending tests, the elastic modulus and the flexural strength of EG/AD/S model ice were evaluated and the results were compared with published test results from Canada. Instead of using an ice model basin, a cold room facility was used for making a model ice specimen. Since the cold room adopts a different freezing procedure to make model ice, the strength of the model ice specimen differs from the published test results. The reason for this difference is discussed and the future development for a making model ice is recommended.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.6
• /
• pp.120-125
• /
• 2004

There are very few numbers of 115K FPP (Fixed Pitch Propulsion) Tankers for the Baltic ice class IA because the minimum power requirement of FMA (Finish- Swedish Maritime Association) needs quite large engine power and the 40 m Beam is out of calculation range of FMA minimum power requirements. The shipyard has no choice except to increase the engine power to satisfy FMA minimum power requirement Rule. And the operation cost, efficiency of hullform and its building cost are not good from the ship owners' point of view To solve this problem, the experience of ice breaking tanker development and the ice tank test results were adopted. The main idea to reduce the ice resistance is by reducing waterline angle at design load waterline. The reason behind the main idea is to reduce the ice-clearing force. Two hull forms were developed to satisfy Baltic Ice class IA. Two ice tank tests and one towing tank test was performed at MARC (Kvaener-Masa Arctic Research Center) and SSMB (Samsung Ship Model Basin) facilities, respectively. The purpose of these tests was to verify the performance in ice and open water respectively The hull form 2 shows less speed loss compared to Hull form 1 in open water operation but hull form 2 shows very good ice clearing ability. finally the Hull Form 2 satisfying Baltic ice class IA. The merit of this hull form is to use the same engine capacity and no major design changes in hull form and other related designs But the hull structure has to be changed according to the ice class grade. The difference in two hull form development methods, ice model test methods and analysis methods of ice model test will be described in this paper.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.2
• /
• pp.363-379
• /
• 2014

In an effort to cope with recent high oil price and global warming, developments of air lubricated ships have been pursued to reduce greenhouse gas emissions and to save fuel costs by reducing the frictional resistance. In this study, reduction in the frictional resistance by air lubrication with air layers generated on the lower surface of a flat plate was investigated experimentally in the large water tunnel of SSMB. The generated air layers were observed, and changes in the local frictional drag were measured at various flow rates of injected air. The results indicated that air lubrication with air layers might be useful in reducing the frictional resistance at specific conditions of air injection. Accordingly, resistance and self-propulsion tests for a 66K DWT bulk carrier were carried out in the towing tank of SSMB to estimate the expected net power savings.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.5 s.149
• /
• pp.550-559
• /
• 2006

A design procedure for a ship with minimum total resistance was developed using a numerical optimization method called SQP(Sequential Quadratic Programming) and a CFD technique based on the Rankine source panel method with the nonlinear free surface boundary conditions. During the whole optimization process the geometry of the hull shape was represented based on the NURBS(Non-uniform rational B-spline) technique and the modification of the hull shape was controlled using the Bell-shaped distribution function to keep the fairness of the hull shape before and after the hull modification. The numerical analysis was carried out using 4000TEU container ship in the towing tank facility installed in the Pusan national university to know the validity of the developed algorithm for this study. As the results of the numerical analysis it proved that the resistance of the optimized hull is conspicuously reduced in comparison with the original hull in a wave-making resistance point of view.

• Journal of the Society of Naval Architects of Korea
• /
• v.37 no.2
• /
• pp.109-117
• /
• 2000

In order to develope ship hull forms. many various models are represented numerically in terms of B-spline surfaces and tested experimentally in the towing tank. It is very difficult to make various ship hulls with free forms in handiwork. As the first step of development of a free form cutting machine which becomes a good substitute for high-priced model cutting machines, free forms representation for model cutting are developed. In this paper, NURBUS surfaces are represented on the assumption that data points may be control points contrary to existing methods.

• Journal of the Society of Naval Architects of Korea
• /
• v.37 no.2
• /
• pp.30-37
• /
• 2000

The roll damping characteristics of the three models of a 3ton class fishing vessel, that is the bare hull, hull with bilge keels, and hull with bilge keels and a central wing are investigated by the free roll tests in head waves in a towing tank with the variations of the forward speed, initial angle and OG. The wave length variations are also included. The experimental results are compared with the numerical results of mathematical modellings by the energy method for these three models and the energy dissipation patterns are also compared. The roll damping speed increases, the effect of the waves on the roll damping of the models with the additional devices is negligible due to the much increased damping caused by the lift increase.