• 한국분무공학회지
• /
• 제22권1호
• /
• pp.1-7
• /
• 2017

Recently, Performance and fuel efficiency of gasoline engines have been improved by adopting direct injection (DI) system instead of port fuel injection (PFI) system. However, injecting gasoline fuel directly into the cylinder significantly reduces the time available for mixing and evaporation. Consequently, particulate matters(PM) emissions increase. Moreover, as the emission regulations are getting more stringent, not only the mass but also the total number of PM should be reduced to satisfy the Euro VI regulations. Increasing the fuel injection pressure is one of the methods to meet this challenge. In this study, the effects of increased fuel injection pressures on combustion and emission characteristics were experimentally examined at several part load conditions in a 1.6 liter commercial gasoline direct injection engine. The main combustion durations decreased about $2{\sim}3^{\circ}$ in crank angle base by increasing the fuel injection pressure due to enhanced air-fuel mixing characteristics. The exhaust emissions and number concentration distributions of PM with particle sizes were also compared. Due to enhanced combustion characteristics, THC emissions decreased, whereas NOx emissions increased. Also, the number concentrations of PM, larger than 10 nm, also significantly decreased.

• Structural Engineering and Mechanics
• /
• 제38권5호
• /
• pp.633-649
• /
• 2011

The paper presents a study aimed at understanding some characteristics of an interior explosion within a room with limited or no venting. The explosion may occur in ammunition storage or result from a terrorist action or from a warhead that had penetrated into this room. The study includes numerical simulations of the problem and analytical derivations. Different types of analysis (1-D, 2-D and 3-D analysis) were performed for a room with rigid walls and the results were analyzed. For the 3D problem the effect of the charge size and its location within the room was investigated and a new insight regarding the pressure distribution on the interior wall as function of these parameters has been gained. The numerical analyses were carried out using the Eulerian multi-material approach. Further, an approximate analytical formula to predict the residual internal pressure was developed. The formula is based on the conservation law of total energy and its implementation yields very good agreement with the results obtained numerically using the complete statement of the problem for a wide range of explosive weights and room sizes that is expressed through a non-dimensional parameter. This new formula is superior to existing literature recommendations and compares considerably better with the above numerical results.

• 한국해양환경ㆍ에너지학회지
• /
• 제10권4호
• /
• pp.187-192
• /
• 2007

플런징 쇄파에 의해 실린더에 작용하는 충격력을 실험적으로 고찰하였다. 쇄파는 조파기의 구동주파수를 선형적으로 감소시켜 수조의 목표지점에 파랑을 집중시킴으로써 생성되며, 쇄파의 파형은 등파기울기 스펙트럼을 채택하였다. 실린더와 쇄파 전면의 접촉각이 충격력에 미치는 영향을 고찰하기 위해 3개의 경사각을 적용하였으며, 압력 분포 및 정점 값에 대한 실린더 직경의 영향을 살피기 위해 3개의 서로 다른 직경을 갖는 실린더가 사용되었다. 충격 압력의 최대 값을 찾기 위해 실린더를 수조 길이방향으로 조금씩 이동하며 총 8개 지점에서 실험을 수행하였다. 실린더 표면의 압력과 합력은 piezo-electric형 압력계와 3축 로드셀을 사용하여 30 kHz의 빈도로 계측하였다. 실린더 직경, 경사각 및 회전각에 따른 정점 충격압력과 충격력의 변화를 분석하였으며, 실린더 표면의 압력분포를 고찰하였다. 실린더의 수조 내 위치 및 실린더 표면의 위치는 정점압력의 크기와 시계열 형상을 지배하는 주요 인자이며, 반면에 실린더 직경과 경사각의 영향은 상대적으로 미미하다. 충격현상은 매우 불안정하기 때문에 동일조건의 반복 실험에서도 계측 값의 넓은 분포가 발생한다.

• 에너지공학
• /
• 제29권3호
• /
• pp.97-102
• /
• 2020

본 연구에서는 화재가 발생하였을 때 작동되는 옥외형 피난계단 구조물이 태풍에 따른 풍압이 작용하였을 때 내구성을 검증하기 위하여 단방향 유동-구조 연성해석을 진행하였다. 이를 위해, 피난계단 구조물 주위에 대한 유동장을 정상상태로 유동해석을 수행하였고, 이러한 해석결과를 구조해석을 위한 입력 데이터로 사용하여 구조응력, 변형량, 피로수명 등의 계산을 통해 내구성을 분석하였다. 유동해석 결과, 피난계단 구조물 형상에 따라 공기에 의한 유동 흐름이 다르게 나타났으며, 이러한 유동속도 분포는 구조물 표면에 전압력으로 작용하였다. 또한, 이러한 전압력에 의해 계산된 구조해석 결과, 최대응력값으로 계산된 안전율이 허용치 이상으로 나타났으며, 피로수명과 변형량 분석을 통해 내구성을 입증하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.819-824
• /
• 2000

The flow inside an axial turbomachinery must be unsteady. Rotor-stator interaction by two blade rows influences performance, the generation of noise and vibration. So, it will be necessary to study the rotor-stator interaction for the design of an axial fan in which the axial gap between two blade rows is small. In this study, rotor-stator interaction is investigated by experimental methods. The research fan has one stage which consists of 24 rotor blades and 22 stator blades. Three-dimensional velocities measured using $45^{\circ}$ slanted hot wire probe and total pressure is measured using Kiel total pressure probe between rotor and stator with the axial 25%, 55%, 145% of chord length,. This study describes the influence of rotor-stator gap on the flow pattern, performance and loss. The efficiency curve show that the change of the rotor-stator gap make difference in the efficiency. And, the 3-dimensional velocity distribution show that the potential interaction between the rotor and the stator have a great effect on the flow field downstream of rotor, where there are wake flow. various vortices in hub region and leakage vortex in casing region etc.

• 대한조선학회논문집
• /
• 제31권3호
• /
• pp.100-111
• /
• 1994

고속정은 spray를 수반하는 흐름 특성을 가지고 있다. 본 연구에서는 이러한 spray의 흐름 특성을 파악하기 위해 몇가지 실험을 수행하였다. 우선 아크릴판으로 만든 주상활주선형을 이용하여, 예인수조에서 흐름의 가시화를 수행하고, 그 기록으로부터 화상해석을 통하여 spray흐름의 방향, 유속등을 계측하였다. Spray에 의해 발생하는 모델의 양력, 항력을 구하기 위해서는 spray의 두께가 주요한 계측 항목이 된다. 본 연구에서는 운동량 이론을 이용한 새로운 spray의 두께 계측법을 제시하였다. Spray의 두께를 국부적으로 계측하여 저항성분을 구하여 적분하므로써, 본 실험모델이 받는 저항성분중 spray저항을 평가하였다. 또한 활주모델의 저면에서 압력을 계측하여 spray가 발생하는 원리를 보여 주었으며, 계측된 압력을 적분하므로써 모델에 작용하는 압력저항성분을 평가하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권5호
• /
• pp.488-494
• /
• 2005

The ejector is used to obtain a vacuum state, and it has been applied to a lot of industry field such as a heat engine, a fluid instrument power plant. a food industry, an environment industry etc., because there is no problem even it is mixed with any kind of liquid, gas. and solid. The flow characteristics in the ejector was investigated by a PIV and a CFD. The agreement between numerical analysis and experiment shows the validity of this study and the results of this study would be useful to the engineers who design for the flow systems for heating. ventilation. air conditioning and wastewater purification plants.

• 한국유체기계학회 논문집
• /
• 제2권4호
• /
• pp.16-23
• /
• 1999

The characteristic of unsteady flowfields on gas turbine, particularly on a rotor blade surface has been numerically investigated. The unsteady flow in a rotor blade passage as a result of wake/blade interaction is modeled by the inviscid flow approach, and solved by Euler equations using a time accurate marching scheme. Unsteady flow in the blade passage is induced by periodically moving a wake model across the passage inlet. The wake model used in this study is the Gaussian wate model in which the wake flow is assumed to be parallel with uniform static pressure and uniform relative total enthalpy. Numerical results show that for the case of Ps/Pr=1.5, the velocity and pressure distribution on the blade surfaces have much more complex profiles than for the case of Ps/Pr=1.0.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2001년도 추계 학술대회논문집
• /
• pp.44-50
• /
• 2001

A numerical study was made to choose the better turbulence model for the flow in the discharge flow path from a diffuser to a wall. In this study standard $\kappa-\epsilon$ model(SKE), RNG $\kappa-\epsilon$ model(RNG), and Reynolds stress model(RSM) were applied. In case of the flow with relatively high Reynolds number at a diffuser inlet, the pressure loss coefficients by RNG have a tendency to be near to those by SKE at small ratio(below about 0.35) of $h/D_o$, but to those by RSM at large ratio(above about 0.35). At large ratio RNG begins to enlarge the effects of rapid strain and streamline curvature. RNG & RSM are recommended as the appropriate turbulence models for this case. But it is noticeable that the velocity gradient pattern in RNG is same as in SKE, and also that the total pressure distribution in RNG is same as in RSM only at swirling flow area, same as in SKE only at main flow area.

• 한국연소학회지
• /
• 제12권1호
• /
• pp.21-27
• /
• 2007

The supersonic combustion experiments are carried out using T3 free-piston shock tunnel. Different shock tube fill pressures have various inflow conditions. $15^{\circ}$ inclined hydrogen fuel injection is located before the cavity. Oblique shock is generated at the trailing edge of the cavity and reflects off the top and bottom wall. For non-reacting flow, static pressures in low equivalence ratio are similar to those in no fuel injection. As equivalence ratio is increased, static pressures are increased in the duct. In the similar equivalence ratio, static pressures are increased when total enthalpy is decreased. For reacting flow, the flame is occurred near the cavity. The combustion is weak locally in the middle of the duct. The up and down pressure distribution in the duct means that the supersonic combustion is generated.