• Journal of Forest and Environmental Science
• /
• v.31 no.1
• /
• pp.14-23
• /
• 2015

In this study, we investigated the effects of three land uses on soil properties in two soil layers; surface soil (0~15 cm) and subsoil (15~30 cm). Soil samples were collected from planted forest, barren lands and cultivated lands from different areas in Chittagong Cox's Bazar and analyzed for some physical and chemical properties. Results showed that soil textural class varied from sandy clay loam in planted forest and barren land site to sandy loam in cultivated soils. Maximum water holding capacity was higher in forest followed by barren land and the lowest in cultivated lands. At both soil depths, soils of cultivated land showed the highest values of bulk density (1.42 to $1.50g\;cm^{-3}$), followed by barren lands (1.37 to $1.46g\;cm^{-3}$) and the least (1.32 to $1.45g\;cm^{-3}$) in forest soils. Total porosity decreased with depth ranging from 40.24% to 41.53% in subsoils and from 42.04 to 43.23% in surface soil of cultivated and of planted forest sites respectively. The result further revealed that organic carbon (OC) and total nitrogen (TN) contents were higher in the planted forest soil than in other two land uses. The soils of all land uses under study are acidic in nature and the lowest pH was found in both surface and subsoils of barren land. Cultivated soil contained the highest amount of available P, Ca, Mg and K in both surface soil and subsoils. In contrast, barren site had the lowest contents of available P, Ca, Mg and K in both layers. The soil organic carbon (SOC) and total N storage were higher in planted forest than in barren and cultivated land uses.

• Journal of Bio-Environment Control
• /
• v.14 no.3
• /
• pp.182-189
• /
• 2005

This research was conducted to determine physical properties of four root media, peatmoss + vermiculite (1:1, v/v; PV), peatmoss + composted rice hall (1:1, PR), peatmoss + composted saw-dust (1:1 : PS) and peatmoss + composted pine bark (1:1 PB), as influenced by incorporation rate of Stock-sorb C (STSB). Each root medium containing STSB was packed in 22 cm diameter plastic pot and the physical properties were determined at 5 weeks after packing. As incorporation rate of STSB were elevated, total porosity increased in PV, PS and PB media with statistical differences at $5{\%}$ level. Those also resulted in increase of container capacity in PS and PB media, but statistical differences were not observed in PV and PR media. Elevated incorporation rate of STSB in PV, PS and PB media resulted in increase of air space with statistical differences. Trends in air space of the three root media showed a linear as well as quadratic responses to STSB contents of media. As incorporation rate of STSB increased, more water was retained in four root media at the soil moisture tension of 4.90 kPa, 9.81 kPa, 29.4 kPa and 1.5 MPa. The amount of water retained in PS medium was the highest at the moisture tension at 29.4 kPa and 1.5 MPa followed by PB, PR and PV medium. These results indicated that elevation of incorporation rate of STSB to various root media increased moisture retention capacity, but did not increase the available water holding capacity.

• The Journal of Engineering Geology
• /
• v.24 no.1
• /
• pp.91-98
• /
• 2014

This paper aims to calculate the increase in groundwater quantity following groundwater dam construction, and to assess its impact on surface water. In the study area of Osib-cheon, Yeongdeok, we estimated groundwater quantity, groundwater level, and effective porosity, and examined surface water fluctuations with respect to the increased groundwater quantity based on the flow duration. The results reveal that the increased groundwater quantity was at most $91,746m^3$ in the total drainage basin of the groundwater dam, and the reduced groundwater quantity was at most $11,259m^3$ in the lower zone of the groundwater dam. Therefore, the total groundwater resources secured was $80,487m^3$ and the decrease in groundwater quantity was just 12.27% of the amount of increase. There were changes in discharge rate by up to $3.00{\times}10^{-2}m^3/s$, as deduced from an analysis offlow duration as a result of groundwater dam construction. The overall difference between before and after construction of the dam was almost insignificant compared with the previous dam. The present results indicate that dammed groundwater can serve as an alternative water resource with sufficient quantity.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.1
• /
• pp.87-96
• /
• 2014

Direct combustion characteristics of coal and oxygen carrier were measured in the thermogravimetric analyzer using four coals and two different oxygen carriers. The direct combustion efficiency decreased in order of Roto, Kideco, Sunhwa and Hyper coal for both oxygen carriers. Moreover, OCN703-1100 oxygen carrier showed better combustion efficiency than OCN706-1100 oxygen carrier for all four coals. The reduction characteristics of two oxygen carriers for $CH_4$, CO and $H_2$ gases were measured in the thermogravimetric analyzer to investigate why OCN703-1100 oxygen carrier showed better combustion efficiency than OCN706-1100 for all coals. The OCN703-1100 oxygen carrier represented higher reduction rate than OCN706-1100 for all reducing gases. Moreover, the total pore area and the porosity of OCN703-1100 were higher than those of OCN706-1100 oxygen carrier. The total volatile gas and volatile components of four coals were measured in a batch type fluidized bed reactor to investigate why the direct combustion efficiency decreased in order of Roto, Kideco, Sunhwa and Hyper coal for both oxygen carriers. The direct combustion efficiency was proportional to the total amount of ($CH_4+CO+H_2$) produced during devolatilization of coals.

• Nuclear Engineering and Technology
• /
• v.53 no.5
• /
• pp.1676-1685
• /
• 2021

We develop a new high-fidelity multiphysics model to simulate boron chemistry in the porous Chalk River Unidentified Deposit (CRUD) deposits. Heat transfer, capillary flow, solute transport, and chemical reactions are fully coupled. The evaporation of coolant in the deposits is included in governing equations modified by the volume-averaged assumption of wick boiling. The axial offset anomaly (AOA) of the Seabrook nuclear power plant is simulated. The new model reasonably predicts the distributions of temperature, pressure, velocity, volumetric boiling heat density, and chemical concentrations. In the thicker CRUD regions, 60% of the total heat is removed by evaporative heat transfer, causing boron species accumulation. The new model successfully shows the quantitative effect of coolant evaporation on the local distributions of boron. The total amount of boron in the CRUD layer increases by a factor of 1.21 when an evaporation-driven increase of soluble and precipitated boron concentrations is reflected. In addition, the concentrations of B(OH)₃ and LiBO₂ are estimated according to various conditions such as different CRUD thickness and porosity. At the end of the cycle in the AOA case, the total mass of boron incorporated in CRUD deposits of a reference single fuel rod is estimated to be about 0.5 mg.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2004.07a
• /
• pp.19-42
• /
• 2004

Sizing properties in paper are generally developed through the application of both internal and surface sizes. Rosin, wax, and synthetic sizes including ASA, AKD, and stearic anhydride are and have been used to provide wet-end sizing to paper. In many cases, the use of some of these sizes leads to runnability problems that are inherent in the wet-end operation. Variability in furnish, fines, broke, filler, water chemistry, conductivity, and pH control impacts the wet-end operation. Size press chemicals including starch and polymers such as styrene-acrylic, styrene-maleic, and styrene acrylate emulsions are used in conjunction with internal sizes to improve the paper surface for printing and strength properties, porosity, and opacity improvement. This paper will discuss results from a new, proprietary formulation and process that allows application of sizing chemistry more totally at the size press with reduced emphasis on wet end sizing. Runnability issues are thus minimized at the wet-end, chemical usage is more efficient, and significant cost savings can be realized. Case histories will be presented illustrating the advantages of this new application in commercial trials.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.4
• /
• pp.754-758
• /
• 2010

In general, Dye-sensitized Solar Cells(DSCs) consist of the nanocrystalline titanium dioxide($TiO_2$) layer which is fabricated on a transparent conductive oxide(TCO) layer such as $F/SnO_2$ glass, a dye adhered to the $TiO_2$, an electrolyte solution and platinum-coated TCO. Among these components, two TCO substrates are estimated to be about 60% of the total cost of the DSCs. Currently novel TCO-less structures have been investigated in order to reduce the cost. In this study, TCO-less DSCs consisting of titanium electrodes were investigated. The titanium electrode is deposited on top of the porous $TiO_2$ layer using electron-beam evaporation process. The porosity of the titanium electrode was found out by the SEM analysis and dye adhesion. As a result, when the thickness of the titanium electrode increased, the surface resistance decreased and the conversion efficiency increased relatively.

• Journal of Environmental Science International
• /
• v.17 no.5
• /
• pp.565-571
• /
• 2008

The surface properties of activated carbon modified by acids and base were studied. The influence of the surface chemistry on the adsorption of benzene and acetone vapor on modified activated carbons has been investigated The modified activated carbons were obtained by treatment with acetic acid ($CH_3COOH$), nitric acid ($HNO_3$) and sodium hydroxide (NaOH). The modified activated carbons had similar porosity but different surface chemistry and adsorption characteristics. The total surface acidity (sum of functional groups) of activated carbon (AC-AN) treated by nitric acid was 2.6 times larger than that of activated carbon (AC) before the acid treatment. Especially, carboxyl group was much developed by nitric acid treatment. The benzene equilibrium adsorption capacity of AC-AN decreased 20% more than that of AC. However, the acetone equilibrium adsorption capacity of AC-AN increased 20% more than that of AC because of the large increase of carboxyl group and acidity.

• Korean Journal of Materials Research
• /
• v.24 no.12
• /
• pp.704-709
• /
• 2014

In this study, we fabricated a novel micro porous hybrid scaffold of biphasic calcium phosphate (BCP) and a polylectrolyte complex (PEC) of chitosan (CS) and hyaluronic acid (HA). The fabrication process included loading of CS-HA PEC in a bare BCP scaffold followed by lypophilization. SEM observation and porosimetry revealed that the scaffold was full of micro and macro pores with total porosity of more than 60 % and pore size in the range of $20{\sim}200{\mu}m$. The composite scaffold was mechanically stronger than the bare BCP scaffold and was significantly stronger than the CS-HA PEC polymer scaffold. Bone morphogenetic growth factor (BMP-2) was immobilized in CS-HA PEC in order to integrate the osteoinductive potentiality required for osteogenesis. The BCP frame, prepared by sponge replica, worked as a physical barrier that prolonged the BMP-2 release significantly. The preliminary biocompatibility data show improved biological performance of the BMP-2 immobilized hybrid scaffold in the presence of rabbit bone marrow stem cells (rBMSC).

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.5-8
• /
• 2005

Sound absorbing performance is affected by porosity and continuity of void, therefore it is important to maintain stabilization of foam and to analyze properties of void pore in hardened state. The purpose of this study is to analyze the sound absorption properties and void characteristic of foamed concrete according to dilution ratio of foaming agent. The results of this experiment were as follows. It is determined that an increase in total and continuous void ratio is achieved by increasing of dilution ratio, and a shorter absorbing time was exhibited at a higher continuous void ratio. When the average void size of foamed concrete was below 1.5mm, the tendency of sound absorption coefficient compared with general sound absorber was appeared similarly.