• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.64 no.4
• /
• pp.308-314
• /
• 2015

This paper has proposed a new boost rectifier. Adequate input current was obtained by keeping the duty ratio constant without complicated conventional control methods and the improvement of the waveform was increased. With a decrease of distortion up to 12.9[%], the scope of restriction on harmonics was set to 13.0[%]($3^{td}$ harmonics), 1.1[%]($5^{td}$ harmonics) and 0.6[%]($7^{td}$ harmonics), respectively. Because complicated methods of control are avoided, the circuit configuration is simple and practical. In particular, the said effect turned out to be highly efficient in the low boosting ratio range(boosting ratio$({\alpha})=1.25$). The feasibility of these facts has been proven both theoretically and experimentally.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.1012-1016
• /
• 1998

According to the adoption of inverter circuit topology for welding machine area, the improvement of welding performance can be achieved. However conventional CO2 inverter arc welding machine uses the constant voltage characteristics. So the metal transfer is performed under unoptimum condition in the sence of spatter generation. In this paper the new control algorithm is proposed for welding machine, which is the instantaneous output current control method using single chip microprocessor. But the optimum waveform of welding current is still uncertain, as a first step for figuring out the optimized waveforms, this study was performed. And as a result of performance test of the proposed system, it was demonstrated that all of the waveform variation parameter could be set individually and the generated spatter is reduced compared to conventional inverter arc welding machine.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.10
• /
• pp.2043-2052
• /
• 1994

This paper proposes a new parallel ASIC architecture for real-time image processing to reduce inter-processing element (inter-PE) communication overhead, called a Sliding Memory Plane (SliM) Image Processor. The Slim Image Processor consists of $3\times3$ processing elements (PEs) connected by a mesh topology. With easy scalability due to the topology. a set of SliM Image Processors can form a mesh-connected SIMD parallel architecture. called the SliM Array Processor. The idea of sliding means that all pixels are slided into all neighboring PEs without interrupting PEs and without a coprocessor or a DMA controller. Since the inter-PE communication and computation occur simultaneously. the inter-PE communication overhead, significant disadvantage of existing machines greatly diminishes. Two I/O planes provide a buffering capability and reduce the date I/O overhead. In addition, using the by-passing path provides eight-way connectivity even with four links. with these salient features. SliM shows a significant performance improvement. This paper presents architectures of a PE and the SliM Image Processor, and describes the design of an instruction set.

• The KIPS Transactions:PartA
• /
• v.17A no.4
• /
• pp.203-212
• /
• 2010

Recently, in automotive industry, there have been many researches related with hardware components and embedded software which controls hardware components. Since most of embedded software is tightly dependent on car manufacturers, there were some problems in reusability and interoperability of automotive software. In order to solve these problems, AUTOSAR standardized the component-based software architecture of automotive software. In AUTOSAR, several modeling diagrams should be described and their dependencies are also checked. Currently, a few company developed the prototypes of tools supporting AUTOSAR. In this paper, a component modeling tool based on AUTOSAR 3.0 is developed for enhancing the usability of existing tools using Eclipse GMF. The tool is composed of a graphical component modeling tool and a graphical network topology tool. Since these tools are generated based on GMF without hard coding, it is relatively easy to customize the tools for adopting company‘s needs and easy to follow the improvement of the standard and development environments.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.7 no.7
• /
• pp.1547-1568
• /
• 2013

Wireless body area network (WBAN) is an emerging short-range wireless communication network with sensor nodes located on, in or around the human body for healthcare, entertainment and ubiquitous computing. In WBANs, energy is severely constrained which is the prime consideration in the medium access control (MAC) protocol design. In this paper, we propose a novel MAC protocol named Energy-efficient Relay MAC with dynamic Power Control (ERPC-MAC) to save energy consumption. Without relying on the additional devices, ERPC-MAC employs relaying nodes to provide relay service for nodes which consume energy fast. Accordingly the superframe adjustment is performed and then the network topology can be smoothly switched from single-hop to multi-hop. Moreover, for further energy saving and reliability improvement, the dynamic power control is introduced to adjust the power level whenever a node transmits its packets to the coordinator or the relaying node. To the best of the authors' knowledge, this is the first effort to integrate relay, topology adjustment and power control to improve the network performance in a WBAN. Comprehensive simulations are conducted to evaluate the performance. The results show that the ERPC-MAC is more superior to the existing standard and significantly prolongs the network lifetime.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.3
• /
• pp.214-222
• /
• 2015

The superiority of gallium nitride FET (GaN FET) over silicon MOSFET is examined in this paper. One of the outstanding features of GaN FET is low reverse-recovery charge, which enables continuous conduction mode operation of totem-pole bridgeless boost power factor correction (PFC) circuit. Among many bridgeless topologies, totem-pole bridgeless shows high efficiency and low conducted electromagnetic interference performance, with low cost and simple control scheme. The operation principle, control scheme, and circuit implementation of the proposed topology are provided. The converter is driven in two-module interleaved topology to operate at a power level of 5.5 kW, whereas phase-shedding control is adopted for light load efficiency improvement. Negative bias circuit is used in gate drivers to avoid the shoot-through induced by high speed switching. The superiority of GaN FET is verified by constructing a 5.5 kW prototype of two-module interleaved totem-pole bridgeless boost PFC converter. The experiment results show the highest efficiency of 98.7% at 1.6 kW load and an efficiency of 97.7% at the rated load.

• Journal of the Korean Society for Heat Treatment
• /
• v.21 no.1
• /
• pp.10-19
• /
• 2008

To investigate the effect of ultrasonic nano-crystalline surface modification (UNSM) treatment on rolling contact fatigue and residual stress properties of bearing steels, this paper carried out a rolling contact fatigue test, measured residual stress and retained austenite, performed a wear test, observed microstructure, measured micro hardness, and analyzed surface topology. After the UNSM treatment, it was found that the surface became minute by over $100{\mu}m$. The micro surface hardness was changed from Hv730~740 of base material to Hv850~880 with about 20% improvement, and hardening depth was about 1.3 mm. The compressive residual stress was measured as high as -700~-900 MPa, and the quantity of retained austenite was reduced to 27% from 34%. The polymet RCF-6 ball type rolling contact fatigue test showed over 4 times longer fatigue lifetime after the UNSM treatment under 551 kgf load and 8,000 rpm. In addition, this paper observed the samples, which went through the rolling contact fatigue test, with OM and SEM, and it was found that the samples had a spalling phenomenon (the race way is decentralized) after the UNSM treatment. However, before the treatment, the samples had excessive spalling and complete exploration. Comparison of the test samples before and after the UNSM treatment showed a big difference in the fatigue lifetime, which seems to result from the complicated effects of micro particles, compressive residual stress, retained austenite, and surface topology.

• Journal of KIISE:Computing Practices and Letters
• /
• v.9 no.1
• /
• pp.77-85
• /
• 2003

The conversion into a new Local Area Network (LAN) environment without clear analysis of the problems with the conventional LAN environment nay bring about some improvement of performance, but in general, the result would not be as good as expected. Besides, in case new traffic or application programs are added In the near future, traffic overload similar to the past may incur. Therefore, the conversion into a new LAN environment should not only relieve the problems with the conventional environment but also be able to cope with future expansion of the network flexibly. In the present paper, in view of the above, the problems with protocols and traffic that may occur in the Bus-structured 10/100 Mbps shared Ethernet that has been widely used by many institutions are reviewed, and as a case study whether such conversion into a new LAN environment in order to increase the efficiency in the operation, management, and utilization of the network would be proper for the actual operational environment is implemented, and the results are analyzed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.5
• /
• pp.1608-1615
• /
• 2010

In this paper, we proposed the method called "DoublePico"(Double Piconet) forovercoming low data transmission rate in a scatternet. This needs a new Ad-hoc network topology to transmit with high rate. Every node performs the function of the relay station. DoublePico has two bluetooth devices that should form two different poconets; every node can make a link between two different piconets. Two different piconets are linked in one node by the link with two bluetooth divices thereby forming the Ad-Hoc network. In this paper, we shows the method of DoublePico which supports about 457kbps of the maximum data transmission rate. This method supports a higher data transmission rate than the traditional bluetooth's Ad-Hoc topology by using analysis and comparison of existing algorithm of bluetooth specification and simulation results. Specifically, this paper focuses on the impact of intererence on the PER (Packet Error Rate), throughput performance, and the throughput improvement with SAW(Stop and Wait)-ARQ scheme in DoublePico.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.10
• /
• pp.1903-1911
• /
• 2016

As interest in MANET is increasing nowadays, research upon an efficient MANET routing protocol is actively under way. A LQA(Link Qualty Aware)-AODV routing protocol to deal with frequent changes of topology and wireless link variations under tactical operating conditions is proposed in this paper. The suggested LQA-AODV takes into account the channel capacity of each hop during the route request process of the traditional AODV protocol. In detail, LQA-AODV adds a channel capacity cost value to the RREQ message format that occurs during the routing process of the existing AODV Routing Protocol causing the accumulated channel capacity cost values of each sections to be compared before establishing a route. To verify the performance of LQA-AODV, NS2.35 was utilized and the Link-Quality Model was applied in order to reflect the tactical wireless environment. The simulation compares and analyzes LQA-AODV and the existing AODV, showing a large improvement over the traditional AODV in regards to the Packet Delivery Ratio, and End-to-End Delay.