• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.475-478
• /
• 2001

This study is to examine the safety by analizing the hardness of bed and the characteristic of vibration to improve basic efficiency of machine-tool of drill-cell which is a high line center. The mistake of existing design was shown through the analysis of 3-D and structure. The purpose of this study is to prevent from a problem which may happen after this and to produce more reliable machine-tool by carrying out and finding out an adequate countermeasure for bed at the cutting position.

• Korean Journal of Materials Research
• /
• v.27 no.6
• /
• pp.331-338
• /
• 2017

This study was carried out to investigate the optimum condition of a friction stir welding process for a joint of AA2219-T87 and AA2195-T8 dissimilar aluminum alloys. These alloys are known to have good cryogenic properties, and as such to be suitable for use in fuel tanks of space vehicles. The welding parameters include the travelling speed, rotation speed and rotation direction of the tool. The experiment was conducted under conditions in which the travelling speed of the tool was 120-300 mm/min and the rotation speed of the tool was 400-800 rpm. To investigate the effect of the rotation direction of the tool, the joining was performed by switching the positions of the two dissimilar alloys. After welding, the microstructure was observed and the micro-hardness were measured; non-destructive evaluation was carried out to perform tensile tests on defect-free specimens. The result was that the microstructure of the weld joint underwent dynamic recrystallization due to sufficient deformation and frictional heat. The travelling speed of the tool had little effect on the properties of the joint, but the properties of the joint varied with the rotation speed of the tool. The conditions for the best joining properties were 600 rpm and 180-240 mm/min when the AA2219-T8 alloy was on the retreating side(RS).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3151-3157
• /
• 2013

Rib cutting is being used to many electronic components and small plastic products. In this study, comparison experiment on tool of flat type(2F) and single edge type(1F) was conducted. Results were as follows: Surface roughness and tool wear of straight cutting showed good results in tool with a straight structure of the Existing tool. Rib cutting of 7mm depth was shown 50% higher surface roughness of development tool than the existing tool. The cutting time varies depending on the shape of the rib. But it is three times faster compared to existing tool.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.404-409
• /
• 2004

To maximize the productivity in machining molds and dies, machine tools should operate at high speeds. During the high speed operation of moving frames or spindles, vibration problems are apt to occur if the machine tool structures are made of conventional steel materials with inferior damping characteristics. However, self-excited vibration or chatter is bound to occur during high speed machining when cutting speed exceeds the stability limit of machine tool. Chatter is undesirable because of its adverse effect on surface finish, machining accuracy, and tool life. Furthermore, chatter is a major cause of reducing production rate because, if no remedy can be found, metal removal rates have to be lowered until vibration-free performances is obtained. Also, the resonant vibration of machine tools frequently occurs when operating frequency approaches one of their natural frequencies because machine tools have several natural frequencies due to their many continuous structural elements. However, these vibration problems are closely related to damping characteristics of machine tool structures. The polymer concrete has high potential for machine tool bed due to its good damping characteristics with moderate stiffness. This paper presents the use of polymer concrete and sandwich structures to overcome vibration problems. Also, co-cure bonding method for functional part mounting was exhibited experimentally, by which manufacturing time and cost for polymer concrete bed will be remarkably reduced.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.9
• /
• pp.4248-4270
• /
• 2018

This research aims at a new practical Intent fuzzing tool for detecting Intent vulnerabilities of Android apps causing the robustness problem. We proposed two new ideas. First, we designed an Intent specification language to describe the structure of Intent, which makes our Intent fuzz testing tool flexible. Second, we proposed an automatic tally method classifying unique failures. With the two ideas, we implemented an Intent fuzz testing tool called Hwacha, and evaluated it with 50 commercial Android apps. Our tool offers an arbitrary combination of automatic and manual Intent generators with executors such as ADB and JUnit due to the use of the Intent specification language. The automatic tally method excluded almost 80% of duplicate failures in our experiment, reducing efforts of testers very much in review of failures. The tool uncovered more than 400 unique failures including what is unknown so far. We also measured execution time for Intent fuzz testing, which has been rarely reported before. Our tool is practical because the whole procedure of fuzz testing is fully automatic and the tool is applicable to the large number of Android apps with no human intervention.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.1
• /
• pp.36-45
• /
• 1983

In order to characterize the machine tool feed-drive dynamics, thread cutting experiments are performed with cutting conditions and slide-way lubrication varied. During the experiments, the carriage, tool post and tail stock accelerations in the feed direction are measured, and analyzed by employing the spectral analysis method. It is found that the tool post vibration in the feed direction during thread cutting operation is mainly due to those of the carriage and the workpiece. Other structure-related vibrations show little effects on the tool post vibration. The characteristics of the carriage vibration is shown to be fairly consistent, except the vibration amplitude, regardless the variations in cutting condition and lubrication within the experimental range. The experimental results suggest that the feeddrive system can be modelled as a 2 DOF damped oscillatory system.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.1
• /
• pp.37-42
• /
• 1990

Carbon fiber epoxy composite materials are widely used in the structures of aircrafts, robots and other machines because of their high specific stiffness, high specific strength and damping. In order for the composite materials to be used in the robot structure or machine element, bearing mounting and joining surfaces must be provided, which require accurate machining. In this paper, the machinability and tool wear characteristics of the milling operation of the carbon fiber epoxy composite materials were experimentally measured. The tool wear mechanism and the Taylor tool wear constants were determined. Also, the surface roughness of milling operation was measured w.r.t. cutting speed and feed.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.185-189
• /
• 2001

In order to prevent the production defects the optimum design of product, jig and fixture putting in the field is very significant manufacturing method. Drilling Jig is the device according to industrial demand for multi manufacturing products on the growing at alarming rate. In the field of design and making for machine tool working, welding, assembling with jig and fixture for mass production is a specific division. They require analysis of many kinds of important factors, theory and practice of machine tool operating process and jig & fixture structure, machining condition for tool making, tool materials, heat treatment of jig & fixture components, know-how and so on. In this study we designed and constructed a drilling jig of mass production and performed tryout under the Auto CAD, Auto Lisp database, that we made by database, and window environment. Especially this study is reveals with the analysis of part drawing, jig planning, jig design etc, and then the result of drill jig's making try out.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.429-433
• /
• 1997

High-speed and high-precision are trendy at present in the development of machine tools which are required for various fields of industry such as semiconductor, automobde, mold fabricat~on and so on. High damping capacity of the structure is an iniportant factor to ohtain precise products without vibration during manufacturing caused by rapid trarisportatm and rotation of spindle unit Resin concrete have high potential for machine tool bed due to its good damping characteristics. In this study, the statlc and dynamic characteristics of the machine tool bed were analysed. Also, the hybrid machine tool bed, made of steel base and polyester resin concrete material, was manufactured and its good dynamic characteristics were proved experimentally.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.5
• /
• pp.714-719
• /
• 2012

In this paper, the polishing force monitoring and the control method were implemented for the polishing machine with the airbag tool. Airbag tool has been known to be adaptable to the curvature variation such as the aspherical and the free-form surface. However, it was necessary to control the tool movement of vertical axis also because of the table rotational wobble and vibration. To solve it by the polishing force control, we installed another stepping motor to the z-axis. And the polishing force was measured with the load cell and controlled by the PID Labview controller. A few hundreds gram of the polishing force were well controlled under 0.8 second of the response time and 5% variation. An experiment was done to clean the edge burrs of the micro channel structure of width $87{\mu}m$ using the polishing force control.