• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.8
• /
• pp.655-662
• /
• 2009

In order to obtain knowledge on the design and operation of practical?scale Cylinder-Shaped Filters, pilot experiments were conducted to observe the effects of stepwise augmentation of production rate on water quality and clogging. A production rate increase from 0.8 L/min to 2.4 L/min did not appear to affect the removal efficiencies of BOD(Biochemical Oxygen Demand), SS(Suspended Solids), and turbidity, as the values were maintained around 80%, over 95%, and over 90% respectively;however, COD(Chemical Oxygen Demand) removal decreased from 44% to 29%. In addition, results indicated an inverse relationship between production rate and detention time required to remove unit contaminant concentration, the observed detention time in the filter to remove 1 mg-COD/L being 83 minutes for the production rate of 0.8 L/min and 45 minutes for the production rate of 2.4 L/min, suggesting that a relatively higher production rate is likely to be more advantageous in the purification of reservoir water when compared to a lower production rate. Clogging was observed to originate from the surface and advance to the center of the filter, and although clogging seemed to increase as the production rate increased, this did not cause any difficulties in normal functioning of the filter for more than 2 years of operation, suggesting that this filter system can be used effectively in the purification of reservoir water.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.4
• /
• pp.503-508
• /
• 2007

Small scale D-water treatment plant(WTP) where has slow sand filtration was using raw water containing high concentration of manganese (> 2mg/l). The raw water was pre-chlorinated for oxidation of manganese and resulted in difficulty for filtration. Thus, sometimes manganese concentration and turbidity were over the water quality standard. Two stage rapid manganese sand filtration pilot plant which can treat $200m^3/d$ was operated to solve manganese problem in D-WTP. The removal rate of manganese and turbidity were about 38% and 84%, respectively without pH control of raw water. However, when pH of raw water was controlled to average 7.9 with NaOH solution, the removal rate of manganese and turbidity increased to 95.0% and 95.5%, respectively and the water quality of filtrate satisfied the water quality standard. Manganese content in sand was over 0.3mg/g which is Japan Water Association Guideline. The content in upper filter was 5~10 times more than that of middle and lower during an early operation but the content in middle and lower filter was increased more and more with increase of operation time. This result means that the oxidized manganese was adsorbed well in sand. Rapid manganese sand filter was backwashed periodically. The water quality of backwash wastewater was improved by sedimentation. Thus, turbidity and manganese concentration decreased from 29.4NTU to 3.09NTU and from 1.7mg/L to 0.26mg/L, respectively for one day. In Jar test of backwash wastewater with PAC(Poly-aluminum chloride), optimum dosage was 30mg/L. Because the turbidity of filtrate was high as 0.76NTU for early 5 minute after backwash, filter-to-waste should be used after backwash to prevent poor quality water.

• Journal of Broadcast Engineering
• /
• v.20 no.4
• /
• pp.632-640
• /
• 2015

This paper proposes a new method for fast graphic visualization of accurate frequency response of audio equalizer (EQ). When a logarithmic frequency scale is used, a frequency response in high resolution is required for accurate low-band frequency response. However, the high-resolution frequency response requires a huge amount of computational load, which makes the real-time graphic visualization of frequency response impossible. In order to solve the problem of computational load, the proposed method utilizes a low-resolution virtual frequency response in the mid band. It first computes the virtual frequency response of each filter of EQ in the mid band, and then moves it to the target band so that the result corresponds to the desired filter response. Then, it determines the final frequency response of EQ by combining all filter responses. The experiments confirm that the proposed method provides the frequency response of EQ which has an equivalent shape to that computed in high frequency resolution with huge computational load.

• Journal of Information Processing Systems
• /
• v.19 no.3
• /
• pp.370-376
• /
• 2023

Aiming at the problems of low image enhancement accuracy, long enhancement time and poor image quality in the traditional robot sequence motion image enhancement methods, an adaptive enhancement method for robot sequence motion image is proposed. The feature representation of the image was obtained by Karhunen-Loeve (K-L) transformation, and the nonlinear relationship between the robot joint angle and the image feature was established. The trajectory planning was carried out in the robot joint space to generate the robot sequence motion image, and an adaptive homomorphic filter was constructed to process the noise of the robot sequence motion image. According to the noise processing results, the brightness of robot sequence motion image was enhanced by using the multi-scale Retinex algorithm. The simulation results showed that the proposed method had higher accuracy and consumed shorter time for enhancement of robot sequence motion images. The simulation results showed that the image enhancement accuracy of the proposed method could reach 100%. The proposed method has important research significance and economic value in intelligent monitoring, automatic driving, and military fields.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.2
• /
• pp.37-46
• /
• 2007

This study developed composition-plastic media with woodchips and plastic as main materials, and examined the performance of media. Compared to the existing commercial media, the media had similar performance in removal efficiency and microbes attaching characteristic, and was evaluated that they are distinguished from economic side. Performance test of media was conducted to examine the removal capacity of toluene and hydrogen sulfide in a gas stream by using a lab-scale biotrickling filter systems packed with them. At a volumetric loading of $1.5\;m^3/hr$ with inlet concentration 260 ppm and empty bed residence time (EBRT) 42s, the toluene removal efficiency was shown over 90%, and the maximum elimination capacity of toluene in the biotrickling filter was $77g/m^3{\cdot}hr$. Effective co-treatments of $H_2S$ and Toluene were observed in the lab-scale biotrickling filters. The maximum elimination capacity of $H_2S$ was $100\;g-S/m^3{\cdot}hr$. Up to 100 ppm, the concentration of $H_2S$ did not have an effect on toluene removal efficiency, but the removal efficiency of toluene decreased with increasing inlet $H_2S$ concentration.

• Proceedings of the IEEK Conference
• /
• 2000.11d
• /
• pp.155-158
• /
• 2000

In this paper, the quantization noise in block-based video coding is analyzed, and a post-processing method based on the analysis is presented for reducing the quantization noise by using a wavelet transform(WT). In the proposed method, the quantization noise is considered as the sum of a blocking noise expressed as a deterministic profile and the random remainder noise. Each noise is removed in a viewpoint of image restoration using a 1-D WT, which yields a regularized differentiation. The blocking noise first is reduced by weakening the strength of each blocking noise component that appears as an impulse in the first scale wavelet domain. The impulse strength estimation is performed using median filter, quantization parameter(QP), and local activity. The remainder noise, which is considered as a white noise at non-edge pixels, then is reduced by soft-thresholding. The experimental results show that the proposed method yields better performance in terms if subjective quality as well as PSNR performance over VM post-filter in MPEG-4 for all test sequences of various compression ratios. We also present a fast post-processing in spatial domain equivalent to that in wavelet domain for real-time application.

• Applied Chemistry for Engineering
• /
• v.26 no.2
• /
• pp.229-233
• /
• 2015

In this study, we examined the removal characteristics of suspended particulate matters which are one of carcinogens to cause lung cancer. The fine dust capture by a pilot scale filtration system depends on several important variables such as humidity, initial fine dust injection volume, and flow rate. The average concentration of particulate matters in the test chamber decreased, but the ultimate collection efficiency did not change during the filtration under high humidity, compared to those of using ambient conditions The initial injection amount of fine dust did not influence the particle capturing efficiency. When the flow rate reduced from 0.6 m/s to 0.3 m/s, the dust collection time increased approximately 1.4 times. Among all variables tested, the flow rate showed the most significant effect on the removal efficiency of fine particulate matter.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.443-447
• /
• 2001

A laboratory-scale electrodewatering system for enhancing conventional filter pressure dewatering by an electric field has been developed to decrease the water content of sludge generated in the wastewater treatment. It consists of a piston-typed filter press, a power supply and data acquisition system. The offset of electrodewatering is investigated as a function of applied pressure, applied voltage, sludge type and filtration time. Also the optimal conditions for maximizing the dewatering efficiency in the eletrodewatering system are investigated. Electric field strength and mechanical pressure are in the range of from 0 to 120 V/cm and from 98.1 to 392.4 kPa. The dewatering rates increased with increasing electric strength. These experiments produced a final sludge cake with water content of 60 wt% using electrodewatering technology, compared with a 80 wt% using pressure filtration alone. The conventional filtration system using the electrodewatering shows the potential to be effective method for improving dewatering Sludge.

• ETRI Journal
• /
• v.37 no.4
• /
• pp.752-765
• /
• 2015

We propose a novel post-processing algorithm and its very-large-scale integration architecture that simultaneously uses the passive and active stereo vision information to improve the reliability of the three-dimensional disparity in a hybrid stereo vision system. The proposed architecture consists of four steps - left-right consistency checking, semi-2D hole filling, a tiny adaptive variance checking, and a 2D weighted median filter. The experimental results show that the error rate of the proposed algorithm (5.77%) is less than that of a raw disparity (10.12%) for a real-world camera image having a $1,280{\times}720$ resolution and maximum disparity of 256. Moreover, for the famous Middlebury stereo image sets, the proposed algorithm's error rate (8.30%) is also less than that of the raw disparity (13.7%). The proposed architecture is implemented on a single commercial field-programmable gate array using only 13.01% of slice resources, which achieves a rate of 60 fps for $1,280{\times}720$ stereo images with a disparity range of 256.

• Smart Structures and Systems
• /
• v.15 no.1
• /
• pp.169-189
• /
• 2015

Convergence difficulty and available complete measurement information have been considered as two primary challenges for the identification of large-scale engineering structures. In this paper, a time domain substructural identification approach by combining a weighted adaptive iteration (WAI) algorithm and an extended Kalman filter method with a weighted global iteration (EFK-WGI) algorithm was proposed for simultaneous identification of physical parameters of concerned substructures and unknown external excitations applied on it with limited response measurements. In the proposed approach, according to the location of the unknown dynamic loadings and the partially available structural response measurements, part of structural parameters of the concerned substructure and the unknown loadings were first identified with the WAI approach. The remaining physical parameters of the concerned substructure were then determined by EFK-WGI basing on the previously identified loadings and substructural parameters. The efficiency and accuracy of the proposed approach was demonstrated via a 20-story shear building structure and 23 degrees of freedom (DOFs) planar truss model with unknown external excitation and limited observations. Results show that the proposed approach is capable of satisfactorily identifying both the substructural parameters and unknown loading within limited iterations when both the excitation and dynamic response are partially unknown.