• 제목/요약/키워드: Time of Gas Emission

검색결과 452건 처리시간 0.048초

서울시 중앙버스전용차로 도입의 부가적인 대기오염 영향성 평가 (Impact of the Exclusive Median Bus Lane System on Air Pollution Concentrations in Seoul, Korea)

  • 백연주;김다울;권혜영;김영국;김선영
    • 한국대기환경학회지
    • /
    • 제34권4호
    • /
    • pp.542-553
    • /
    • 2018
  • Since many previous studies reported the health effect of air pollution and indicated traffic as a major pollution source, significant policy efforts have been made to control traffic to reduce air pollution. However, there have been few studies that evaluated such policy implementation. In Seoul, Korea, the exclusive median bus lane system was implemented in 2004, and the metropolitan government applied air pollution reduction policies such as conversion of diesel buses to compressed natural gas buses and installation of emission control devices. This paper aimed to investigate the impact of the exclusive median bus lane system on air pollution reduction. Using hourly concentrations of particulate matter ($PM_{10}$) and nitrogen dioxide ($NO_2$) measured at 131 regulatory monitoring sites in Seoul and Gyeonggi-do for 2001-2014, we calculated annual and daily average concentrations at each site. We assessed the impact of the policy using differences-in-differences analysis by annual and daily average models after adjusting for geographic and/or meteorological variables. This method divides population into treatment and control groups with and without policy application, and compares the difference between the two time periods before and after the policy implementation in the treatment group with the difference in the control group. We classified all monitoring sites into treatment and control groups using two definitions: 1) Seoul vs. Gyeonggi-do; 2) within vs. outside 300 meters from the median bus lane. Pre- and post-policy periods were defined as 2001-2005 and 2006-2014, and 2004 and 2014 in the annual and daily models, respectively. The decrease in $PM_{10}$ concentrations between the two periods across monitoring sites in the treatment group was larger by $1.73-5.88{\mu}g/m^3$ than in the control group. $NO_2$ also showed the decrease without statistical significance. Our findings suggest that an efficient public transport policy combined with pollution abatement policies can contribute to reduction in air pollution.

혼성장비 차량부 시험평가 및 방위산업기술 보호 제도 개선에 관한 연구 (A Study on Improvement of Test & Evaluation of Vehicle Part in Mixed Equipment and Defense Industrial Technology)

  • 윤흥수;류연승
    • 한국융합학회논문지
    • /
    • 제9권7호
    • /
    • pp.241-249
    • /
    • 2018
  • 상용차량 확대계획 및 군수품 상용화 정책에 의해 군용차량은 민간차량의 플랫폼을 사용하여 개발되고 있다. 그러나 민간차량의 플랫폼 정보가 정비지침서, 전장회로도 등에 담겨 공개되고 있기 때문에 민간차량과 동일한 플랫폼을 사용하는 군용차량도 관련 정보가 노출될 수밖에 없다. 특히 군용차량에 미사일, 레이더 등을 탑재하면 전투 목적을 가진 혼성장비가 되므로 기술보호 적용을 검토하여 정보 유출을 차단해야한다. 혼성장비는 2가지 이상의 장비로 구성된 장비를 말하며, 주장 비 부분과 보조장비 부분으로 구분된다. 본 연구에서는 국내 혼성장비 차량부 시험평가 제도 및 방위산업기술 보호체계의 문제점을 도출하고, 전문가 인터뷰를 통해 개선방안을 도출하는 방법으로 연구를 진행하였다. 개선방안으로 전력화 시점을 기준으로 당시 최신 배출가스 기준이 반영된 엔진을 탑재한다는 조항을 추가하여 민간법령과 육군규정의 혼선을 줄이고, 상용화로 된 군수품의 역할 및 기능을 고려하여 방위산업기술의 요소기술로 선정하였다.

Porous Calcium Silicate(PCS)의 급여수준 및 PCS 입자 크기가 육계의 성장, 파리 및 악취 발생에 미치는 영향 (Effects of Concentration and Size of Porous Calcium Silicate (PCS) in Broiler Feeds on Performances, Fly Generation and Malodorous Gas Emission)

  • 전병수;송준익;전중환;곽정훈;강희설;최희철;김태일;이은솔;남기홍
    • 한국축산시설환경학회지
    • /
    • 제15권2호
    • /
    • pp.115-130
    • /
    • 2009
  • PCS와 zeolite 첨가급여가 육계의 성장능력, 유해가스 및 파리발생에 미치는 영향을 구명하기 위하여 대조구, PCS구, zeolite구를 두었으며 처리구당 4반복, 반복당 브로일러 12수씩 총 144수를 완전임의 배치하여 사양시험을 실시하였다. PCS 급여구는 증체, 사료섭취량이 대조구에 비해 유의적으로 적었으나, 사료효율은 현저하게 개선되었으며 (P<0.05) zeolite와 증체 및 사료요구율은 통계적인 차이가 없었고, 사료섭취량은 감소하였다. 암모니아 가스의 농도는 PCS 급여구와 대조구 간에 유의적인 차이가 없었다. 그러나 PCS 처리구는 zeolite 급여구에 비해 2, 3주령에 현저하게 높은 결과를 보여주었지만(P<0.05) 5주령에는 유의적인 차이가 없었다. PCS 첨가수준이 육계의 성장능력, 유해가스 감소 및 파리발생에 미치는 영향을 구명하기 위하여 대조구, PCS 1.5%구, PCS 3.0%구, PCS 4.5%구를 두었으며 각 처리당 4반복, 반복당브로일러 12수씩 총 192수를 완전임의배치하여 사양시험을 실시하였다. 시험 결과 PCS 1.5% 급여구는 증체량, 사료섭취량은 대조구에 비하여 낮은 경향을 보였지만 통계적인 차이가 없었으며, 사료요구 율은 PCS 3.0%에서 다른 처리구에 비하여 개선되었다. 영양소 소화율과 에너지 이용율은 PCS 처리구에서 대조구보다 높았으며, 3.0% 처리구에서 제일 높았다. 계분에서 발생되는 암모니아 농도는 5주령에 PCS 1.5와 3.0% 처리구에서 대조구에 비하여 현저하게 낮았으며 (P<0.05), 황화수소는 PCS 처리구간에 일관성은 없었지만 1.5% 급여 구에서 대조구에 비하여 현저하게 낮았다(P<0.05). PCS 입자도별 급여가 브로일러의 능력, 유해가스 발생 농도 및 파리 발생에 미치는 영향을 구명하기 위하여 대조구, PCS 20, 50, 90 mesh구를 두었으며 증체 및 사료섭취량은 대조구에 비해 모든 PCS 입자도(20, 50, 및 90 mesh) 급여구에서 유의적으로 감소하였다. 그러나 사료 요구율은 대조구와 처리구들 사이에 유의적인 차이를 나타내지 않았으나 PCS 20 mesh를 급여한 구에서 다소 개선되는 경향을 보였다. 이상의 실험 결과를 토대로 PCS 육계의 영양소 소화율은 대조구보다 개선되었고 암모니아 및 황화수소 농도를 낮추는 경향을 보였으나 이에 대한 더 많은 연구가 필요하다고 사료된다.

  • PDF

질산염 화합물 함유 식물 추출물이 in vitro 반추위 발효성상과 메탄 발생에 미치는 영향 (Effects of Nitrate-rich Plant Extracts on the in vitro Ruminal Fermentation and Methane Production)

  • 이신자;이수경;김민성;이성실
    • 농업생명과학연구
    • /
    • 제50권2호
    • /
    • pp.95-105
    • /
    • 2016
  • 본 시험은 질산염함유 식물 추출물을 이용하여 in vitro 반추위 발효성상 및 반추위 메탄 발생에 미치는 영향을 알아보기 위해 수행되었다. 공시재료는 감자, 당근, 배추, 상추 및 시금치 추출물을 사용하였으며, 발효 기질은 2mm로 분쇄된 timothy 0.3g을 사용하였다. In vitro 실험은 조사료(timothy) 및 배합사료를 6:4의 비율로 급여한 반추위 cannnula가 시술된 한우 암소에서 채취하였다. 반추위액과 McDougall's buffer를 1:2의 비율로 혼합한 발효액을 0.3g timothy와 식물 추출물이 담긴 50mL serum bottle에 혐기상태로 20mL 분주한 뒤, 39℃에서 9, 12, 24, 48시간 동안 발효하였다. pH는 발효 시간이 증가함에 따라 점점 감소하며, 6.31~6.96으로 정상범위였다. 건물 소화율은 9시간 배추 추출물구에서 유의적으로 낮았고, 암모니아 농도는 감자, 배추, 상추 추출물구에서 대조구에 비해 첨가구에서 유의적으로(p<0.05) 낮았으며, 반추위 미생물 성장량은 발효 24시간대의 당근 추출물구에서 높았다(p<0.05). Acetate와 propionate 농도는 대조구에 비해 첨가구에서 유의적으로 낮았으며(p<0.05) butyrate 농도는 첨가구간에 발효시간별로 각각 다른 양상을 보였다. 총 가스 발생량은 발효 12시간 및 24시간대에서 배추, 상추, 시금치 추출물구에서 유의적으로(p<0.05) 낮았으며, 메탄 발생량은 감자, 배추, 시금치 추출물구가 대조구에 비해 유의적으로(p<0.05) 낮았고, 이산화탄소 발생량 또한 첨가구에 비해 대조구에서 유의적으로(p<0.05) 낮았다. 결과적으로 본 시험에 사용된 5종의 질산염 함유 식물 추출물은 반추위 발효에 악영향을 미치지 않으면서 메탄저감 효과를 나타내었다. 특히 배추 추출물은 반추위내 메탄발생을 저감시킬 수 있는 식물추출물로서 가능성이 높은 것으로 사료된다.

폐기물처리시설의 세부검사방법 마련연구(I): 공정별 주요인자 도출 및 물질·에너지수지 산정 (A study on inspection methods for waste treatment facilities(I): Derivation of impact factor and mass·energy balance in waste treatment facilities)

  • 이풀잎;권은혜;손준익;강준구;전태완;이동진
    • 유기물자원화
    • /
    • 제31권1호
    • /
    • pp.69-84
    • /
    • 2023
  • 폐기물처리시설의 지속적인 설치·정기검사에도 불구하고 현장 처리시설에서는 과다소각, 불법투기 악취 등에 대한 민원이 지속적으로 발생하는 것으로 보아 현재의 폐기물처리시설 설치정기 검사방법의 개선이 필요하다고 판단되었다 이에 현재 운영중인 폐기물처리시설(6개분야)을 대상으로 현장조사를 실시하여 각 분야별 폐기물처리공정을 파악하고 검사에 적용된 주요한 운영인자를 파악하고, 주요공정별 물질·에너지수지를 산정하여 폐기물처리시설의 적정 운영 여부를 확인하였다. 주요 운영인자 조사 결과 소각 및 시멘트 소성로, 소각열회수시설 등의 경우 소각에 필요한 소각로의 온도 유지 및 발생되는 대기오염물질의 처리가 가장 주요한 인자였으며, 매립시설의 경우 옹벽의 안정성, 매립 후 발생되는 침출수 및 배출가스 관리가 주요한 인자로 나타났다. 멸균·분쇄시설의 경우 멸균여부(아포균검사)가 가장 중요한 주요인자 이었으며, 음식물류폐기물처리시설의 경우 발효(소화, 부숙) 시 체류시간 및 악취관리가 주요한 인자로 나타났다. 또한 물질에너지수지 산정 결과 소각시설의 경우 폐기물 투입량 대비 바닥재 발생량은 약 14%, 비산재 발생량은 약 3%로 적정 운영되고 있을을 확인하였다. 또한 음식물류폐기물시설 중 혐기성분해시설의 경우 유입량 대비 바이오가스 발생량은 약 17%, 바이오가스 전환효율은 약 81%로 나타났고, 퇴비화시설의 경우 유입폐기물 대비 약 11%의 퇴비가 생산되어 모두 적정운영 되고있음을 확인하였다. 이에 따라 폐기물처리시설 검사방법의 고도화를 이루기 위해 세부검사방법의 정량적 기준 적립 뿐만 아니라 각 시설의 정기검사 시 1년간의 운영자료 등을 수집하여 폐기물의 흐름을 파악하고 처리시설의 적정운영 여부를 판단한다면, 처리시설의 운영 및 관리효율이 상승할 것으로 판단된다.

GWP (Global Warming Potential)를 고려한 가시박 바이오차르의 토양 납 제거 효과 분석 (A Study of Burcucumber Biochars to Remediate Soil Pb Considering GWP (Global Warming Potential))

  • 김유진;박한;김민호;서성희;옥용식;유가영
    • 대한환경공학회지
    • /
    • 제37권7호
    • /
    • pp.432-440
    • /
    • 2015
  • 유기물의 열분해로 생성되는 바이오차는 토양 탄소 저장량을 증가시킴으로써 기후변화를 완화할 수 있는 전략으로 소개되고 있다. 또한 바이오차는 토양의 흡착능을 증대시켜 중금속으로 오염된 토양을 정화할 수 있다고 보고된다. 본 연구는 두 종류 바이오차의 토양 중금속 제거 효과와 함께 기후변화 완화효과를 동시에 알아보기 위해 수행되었다. 두 종류의 바이오차는 가시박 및 차 찌꺼기 바이오매스를 열분해 하여 준비했다. 납으로 오염된 농경지 토양은 바이오차 및 바이오매스와 혼합되어 60일 동안 배양하였다. $CO_2$, $CH_4$, $N_2O$는 배양 기간 동안 주기적으로 측정되었고 토양 분석은 배양 종료 후 아세트산을 이용한 납 추출량을 비롯한 생화학적 요소에 대해 수행하였다. 그 결과, 배양 후 납의 양은 BC_Ch에서 71% 만큼 감소했다. 배양 중 $CO_2$$N_2O$ 발생은 BC_Ch, TW_Ch에서 각각 BC_Bm, TW_Bm 대비 약 24%, 34% 감소하였다. $CH_4$ 발생은 바이오차 처리에 의한 유의한 차이를 나타내지 않았다. GWP 계산 과정에서 온실가스($CO_2$, $CH_4$, $N_2O$), 토양에 처리한 가시박 및 차 찌꺼기 바이오매스와 바이오차, 토양 내 총 탄소량을 고려하였으며, 바이오차 투입으로 토양 내 납의 농도가 감소한 BC_Ch를 제외한 나머지 처리구와 대조구에 제올라이트를 투입하였다고 가정하여 GWP 계산을 수행하였다. BC_Ch가 GWP 측면에서 가장 유리한 것을 보였는데, 이는 가시박 바이오차가 높은 납 흡착과 토양 내 탄소 격리 효과를 나타냈기 때문으로 사료된다. 결론적으로, 가시박으로부터 생성한 바이오차를 투입하는 것이 토양 오염 저감과 기후변화 완화 효과를 동시에 기대할 수 있는 전략임을 시사한다.

PREPARATION OF AMORPHOUS CARBON NITRIDE FILMS AND DLC FILMS BY SHIELDED ARC ION PLATING AND THEIR TRIBOLOGICAL PROPERTIES

  • Takai, Osamu
    • 한국표면공학회:학술대회논문집
    • /
    • 한국표면공학회 2000년도 추계학술발표회 초록집
    • /
    • pp.3-4
    • /
    • 2000
  • Many researchers are interested in the synthesis and characterization of carbon nitride and diamond-like carbon (DLq because they show excellent mechanical properties such as low friction and high wear resistance and excellent electrical properties such as controllable electical resistivity and good field electron emission. We have deposited amorphous carbon nitride (a-C:N) thin films and DLC thin films by shielded arc ion plating (SAIP) and evaluated the structural and tribological properties. The application of appropriate negative bias on substrates is effective to increase the film hardness and wear resistance. This paper reports on the deposition and tribological OLC films in relation to the substrate bias voltage (Vs). films are compared with those of the OLC films. A high purity sintered graphite target was mounted on a cathode as a carbon source. Nitrogen or argon was introduced into a deposition chamber through each mass flow controller. After the initiation of an arc plasma at 60 A and 1 Pa, the target surface was heated and evaporated by the plasma. Carbon atoms and clusters evaporated from the target were ionized partially and reacted with activated nitrogen species, and a carbon nitride film was deposited onto a Si (100) substrate when we used nitrogen as a reactant gas. The surface of the growing film also reacted with activated nitrogen species. Carbon macropartic1es (0.1 -100 maicro-m) evaporated from the target at the same time were not ionized and did not react fully with nitrogen species. These macroparticles interfered with the formation of the carbon nitride film. Therefore we set a shielding plate made of stainless steel between the target and the substrate to trap the macropartic1es. This shielding method is very effective to prepare smooth a-CN films. We, therefore, call this method "shielded arc ion plating (SAIP)". For the deposition of DLC films we used argon instead of nitrogen. Films of about 150 nm in thickness were deposited onto Si substrates. Their structures, chemical compositions and chemical bonding states were analyzed by using X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and infrared spectroscopy. Hardness of the films was measured with a nanointender interfaced with an atomic force microscope (AFM). A Berkovich-type diamond tip whose radius was less than 100 nm was used for the measurement. A force-displacement curve of each film was measured at a peak load force of 250 maicro-N. Load, hold and unload times for each indentation were 2.5, 0 and 2.5 s, respectively. Hardness of each film was determined from five force-displacement curves. Wear resistance of the films was analyzed as follows. First, each film surface was scanned with the diamond tip at a constant load force of 20 maicro-N. The tip scanning was repeated 30 times in a 1 urn-square region with 512 lines at a scanning rate of 2 um/ s. After this tip-scanning, the film surface was observed in the AFM mode at a constant force of 5 maicro-N with the same Berkovich-type tip. The hardness of a-CN films was less dependent on Vs. The hardness of the film deposited at Vs=O V in a nitrogen plasma was about 10 GPa and almost similar to that of Si. It slightly increased to 12 - 15 GPa when a bias voltage of -100 - -500 V was applied to the substrate with showing its maximum at Vs=-300 V. The film deposited at Vs=O V was least wear resistant which was consistent with its lowest hardness. The biased films became more wear resistant. Particularly the film deposited at Vs=-300 V showed remarkable wear resistance. Its wear depth was too shallow to be measured with AFM. On the other hand, the DLC film, deposited at Vs=-l00 V in an argon plasma, whose hardness was 35 GPa was obviously worn under the same wear test conditions. The a-C:N films show higher wear resistance than DLC films and are useful for wear resistant coatings on various mechanical and electronic parts.nic parts.

  • PDF

해양지중에 저장된 이산화탄소의 단층을 통한 누출 위험 평가에 관한 수치해석 연구 (A Numerical Study on the CO2 Leakage Through the Fault During Offshore Carbon Sequestration)

  • 강관구;허철;강성길
    • 한국해양환경ㆍ에너지학회지
    • /
    • 제18권2호
    • /
    • pp.94-101
    • /
    • 2015
  • $CO_2$ 배출을 줄이기 위해서 최근 $CO_2$ 포집 및 저장 기술에 관한 연구가 전세계적으로 활발히 진행되고 있다. 국내에서는 해양퇴적층을 대상으로 한 $CO_2$ 저장 연구가 활발히 진행되고 있다. 이러한 $CO_2$ 저장 연구에서 가장 중요한 요소 중 하나는 안전성 확보이다. 지중저장의 안전성 확보를 위해서 저장 $CO_2$의 누출 가능성과 누출 특성을 예측하는 것은 매우 중요하다. 본 연구에서는 해양지중에 저장된 $CO_2$가 단층을 통하여 누출될 수 있는 시나리오를 가정한 후, 지중공간 내 $CO_2$ 확산 및 누출 거동을 TOUGH2-MP ECO2N을 사용하여 시뮬레이션 하였다. 대상 저장지는 150 m 수심의 대륙붕 해저 825 m 지점에 있는 두께 150 m의 대염수층이고, 누출이 진행되는 경로는 주입정에서 1,000 m 떨어진 단층이다. 저장된 $CO_2$는 주입 압력과 밀도차에 의한 부력에 의해서 이동하게 된다. $CO_2$가 해수면으로 누출되기 위해서는 주입정에서 인가된 압력차가 $CO_2$를 단층 하단에 도달할 수 있게 할 만큼 충분히 커야 한다. 단층 하단에 도달한 $CO_2$는 추가적인 압력 구배가 없어도 부력에 의해서 누출된다. $CO_2$ 주입과 동시에 공극수는 $CO_2$가 누출되기 전까지 지속적으로 해저면으로 누출된다. $CO_2$가 해저면에 도착하면 공극수의 누출은 중단되고, 누출되는 $CO_2$질량에 상응하는 해수가 부력의 반대 작용으로 인해 단층으로 유입되는 것으로 계산되었다. 주입량이 누출에 미치는 영향을 평가하기 위하여 연간 $CO_2$ 주입량 100만 톤, 75만 톤, 50만 톤 에 대한 민감도분석을 수행하였으며, 누출이 일어난 시점은 주입 후 각각 11.3 년, 15.6년, 23.2년으로 계산되었다. 또한, 주입이 종료 된 이후에도 누출은 특정 기간 동안 지속되는 것으로 계산되었다. 누적 주입량 대비 누적 누출량은 연간 $CO_2$ 주입량이 100만 톤, 75만 톤, 50만 톤인 경우, 각각 19.5%, 11.5%, 2.8% 이다.

THE CURRENT STATUS OF BIOMEDICAL ENGINEERING IN THE USA

  • Webster, John G.
    • 대한의용생체공학회:학술대회논문집
    • /
    • 대한의용생체공학회 1992년도 춘계학술대회
    • /
    • pp.27-47
    • /
    • 1992
  • Engineers have developed new instruments that aid in diagnosis and therapy Ultrasonic imaging has provided a nondamaging method of imaging internal organs. A complex transducer emits ultrasonic waves at many angles and reconstructs a map of internal anatomy and also velocities of blood in vessels. Fast computed tomography permits reconstruction of the 3-dimensional anatomy and perfusion of the heart at 20-Hz rates. Positron emission tomography uses certain isotopes that produce positrons that react with electrons to simultaneously emit two gamma rays in opposite directions. It locates the region of origin by using a ring of discrete scintillation detectors, each in electronic coincidence with an opposing detector. In magnetic resonance imaging, the patient is placed in a very strong magnetic field. The precessing of the hydrogen atoms is perturbed by an interrogating field to yield two-dimensional images of soft tissue having exceptional clarity. As an alternative to radiology image processing, film archiving, and retrieval, picture archiving and communication systems (PACS) are being implemented. Images from computed radiography, magnetic resonance imaging (MRI), nuclear medicine, and ultrasound are digitized, transmitted, and stored in computers for retrieval at distributed work stations. In electrical impedance tomography, electrodes are placed around the thorax. 50-kHz current is injected between two electrodes and voltages are measured on all other electrodes. A computer processes the data to yield an image of the resistivity of a 2-dimensional slice of the thorax. During fetal monitoring, a corkscrew electrode is screwed into the fetal scalp to measure the fetal electrocardiogram. Correlations with uterine contractions yield information on the status of the fetus during delivery To measure cardiac output by thermodilution, cold saline is injected into the right atrium. A thermistor in the right pulmonary artery yields temperature measurements, from which we can calculate cardiac output. In impedance cardiography, we measure the changes in electrical impedance as the heart ejects blood into the arteries. Motion artifacts are large, so signal averaging is useful during monitoring. An intraarterial blood gas monitoring system permits monitoring in real time. Light is sent down optical fibers inserted into the radial artery, where it is absorbed by dyes, which reemit the light at a different wavelength. The emitted light travels up optical fibers where an external instrument determines O2, CO2, and pH. Therapeutic devices include the electrosurgical unit. A high-frequency electric arc is drawn between the knife and the tissue. The arc cuts and the heat coagulates, thus preventing blood loss. Hyperthermia has demonstrated antitumor effects in patients in whom all conventional modes of therapy have failed. Methods of raising tumor temperature include focused ultrasound, radio-frequency power through needles, or microwaves. When the heart stops pumping, we use the defibrillator to restore normal pumping. A brief, high-current pulse through the heart synchronizes all cardiac fibers to restore normal rhythm. When the cardiac rhythm is too slow, we implant the cardiac pacemaker. An electrode within the heart stimulates the cardiac muscle to contract at the normal rate. When the cardiac valves are narrowed or leak, we implant an artificial valve. Silicone rubber and Teflon are used for biocompatibility. Artificial hearts powered by pneumatic hoses have been implanted in humans. However, the quality of life gradually degrades, and death ensues. When kidney stones develop, lithotripsy is used. A spark creates a pressure wave, which is focused on the stone and fragments it. The pieces pass out normally. When kidneys fail, the blood is cleansed during hemodialysis. Urea passes through a porous membrane to a dialysate bath to lower its concentration in the blood. The blind are able to read by scanning the Optacon with their fingertips. A camera scans letters and converts them to an array of vibrating pins. The deaf are able to hear using a cochlear implant. A microphone detects sound and divides it into frequency bands. 22 electrodes within the cochlea stimulate the acoustic the acoustic nerve to provide sound patterns. For those who have lost muscle function in the limbs, researchers are implanting electrodes to stimulate the muscle. Sensors in the legs and arms feed back signals to a computer that coordinates the stimulators to provide limb motion. For those with high spinal cord injury, a puff and sip switch can control a computer and permit the disabled person operate the computer and communicate with the outside world.

  • PDF

기포제 종류에 따른 경량기포콘크리트의 기포구조 및 열적특성에 관한 실험적 연구 (An Experimental Study on the Pore Structure and Thermal Properties of Lightweight Foamed Concrete by Foaming Agent Type)

  • 김진만;최훈국;박선규
    • 한국건축시공학회지
    • /
    • 제9권4호
    • /
    • pp.63-73
    • /
    • 2009
  • 최근 건설생산현장에서는 경제가 성장함과 동시에 사회적으로 급격하게 증가하는 건축물의 수요를 충족시키기 위해서 표준화, 대량 생산화가 가능한 건식 공법이 각광을 받고 있다. 이러한 현실에 부응하여 에너지 절감효과 및 공사기간 단축, 다양한 형태로 적용이 가능하고 경제성을 가지는 샌드위치 패널이 많이 사용되고 있다. 샌드위치 패널의 형태는 양면 도장 강판 사이에 유기계 및 무기계 단열재를 합성한 복합 자재이다. 유기계 단열재는 PUR(Poly-uretane foam) 및 EPS(Expanded poly-stylene foam) 등이 사용되며, 무기계 단열재는 Glass wool 및 Mineral wool 등이 사용된다. 유기계 단열재는 화재 시 불이 잘 붙어 대피할 수 있는 시간 부족과 유독가스의 발생으로 인명피해가 크게 발생할 수 있지만, 무기계보다 가격이 싸서 유기계 재료를 사용한 샌드위치 패널이 많이 사용되고 있다. 반면, 무기계 단열재 중 경량기포콘크리트는 단열성과 내화성, 경량성 등이 뛰어나기 때문에 샌드위치 패널에 적용하여 유기계의 단점을 해결하기 위한 많은 연구가 수행되어져 왔다. 단열성 및 내화성, 경량성이 뛰어난 경량기포콘크리트는 기포제를 활용하여 시멘트 경화체 내에 다량의 공극을 발생시켜 제조한 것으로서 역학적 특성은 사용되는 기포제와 발포제의 종류에 따라 많은 영향을 받게 된다. 기포제는 계면활성작용에 의해 물리적으로 기포를 도입하는 것으로써 공기량은 최고 85%까지 생성될 수 있으며, 크게 계면활성제계, 가수분해 단백질계로 구분될 수 있다. 계면활성제계 기포제는 수용액 상에서 기포시키면 안정되고, 점성이 높은 기포가 생기지만 시멘트 슬러리와 혼합 시 안정성이 저하되어 서로 연속된 형태의 기포를 형성한다. 가수분해 단백질계 기포제는 계면활성제계 기포제와는 달리 시멘트 슬러리와 혼합 시 안정되고 서로 독립적인 형태의 기포를 형성하게 된다. 발포제는 금속분말이 알칼리 용액과 접촉하여 수소가스를 발생시키는 원리를 이용하는 것으로써 현재 Autoclaved Light-Weight Concrete(ALC)의 제조에 사용되고 있다. 이와 같이 경량기포콘크리트 제조에 사용되는 기포제 및 발포제는 특성이 각기 다르기 때문에 내부 공극이 변화되고 이에 따라 경량기포콘크리트의 물리적, 단열특성이 변화될 것으로 예상된다. 따라서 본 연구에서는 기포제와 발포제를 사용한 경량기포콘크리트를 샌드위치 패널의 내부 단열재로 활용하는 기초적자료를 제공하기 위한 실험적 연구를 수행하였다. 즉, 경량기포콘크리트를 제조하는데 가장 일반적으로 사용하고 있는 기포제 및 발포제를 대상으로 하여 각각의 첨가량에 따른 경량기포콘크리트의 기포구조 및 열적특성을 검토함으로써 경량기포콘크리트의 높은 단열성능을 확보하기 위한 최적조건을 제시하기 위한 실험 실증적 연구를 수행하였다.