• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 Techno-Fair 및 추계학술대회 논문집 전기물성,응용부문
• /
• pp.150-151
• /
• 2007

We present an one-axis parallel-plate type of bulk micromachined torsional micromirror array with single crystalline silicon (SCS) fabricated on the glass substrate. Structurally, bottom electrodes (amophous silicon) in this mirror are DRIEed along the aluminum mirror patterns on SCS, which are self-aligned with mirror plates. Tracing the history of the micromirror study, we found that few papers have been published on research for uniform driving voltages based upon the tilting direction. If there is a slight misalignment during anodic bonding between top (mirror plate) and bottom electrodes, the non-uniformity of driving voltage will be led depending on two different tilting direction. This paper discusses how much the pull-in voltages can be different due to misalignment between two electrodes. Moreover, We achieve uniform pull-in voltage regardless of misalignments in photolithography and anodic-bonding between two individual layers.

• 유공압시스템학회논문집
• /
• 제2권1호
• /
• pp.1-8
• /
• 2005

Recently, swash plate type hydraulic axial piston motors/pumps are being extensively used in the world, because of simple design, light weight and effective cost. Structural problem of the swash plate type motor/pump is that tilting angle of swash plate should be limited to relatively small value and lateral farce on pistons has an undesirable effect in reciprocating motion. To solve these problems, piston rod mechanism, which is commonly used in bent axis type motor/pump, is considered to be applied to the swash plate type motor/pump. In this paper, kinematic analysis was done on the piston rod mechanism. A series of formula were derived and numerical calculations were done for a set of motor parameters.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.1429-1430
• /
• 2011

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.42-46
• /
• 1993

This paper presents development of a pratical tool deflection compensation system in order to reduce the machining error by the tool deflection in the end-milling process. The system is a tool adapter which includes 2-axis force sensor for detecting tool deflection and 2-axis tool tilting device for adjusting tool position through computer interface in on-line process. In experiments, it is revealed that the force sensor applying parallel plate principle and strain gauge is proper to obtain dynamic process signal, and the tilting device using stepping motor and cam drive mechanism is suitable to have necessary action. By the system and control algorithm, it is possible to get precise machining surface profile without excessive machining error and overcut generated due to increased cutting force in more productive machining condition.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.2191-2194
• /
• 2008

This paper investigates the sound insulation performance of the fiber sandwich panels for a tilting train. Due to the high strength and low mass, fiber sandwich panels are widely used for aircraft structures, railway vehicle structures. These fiber sandwich panels show orthotropic behavior because of the fiber's structural characteristics. This orthotropy often reduces the critical frequency and makes negative effect on the sound insulation performance. In this study, transmission loss of the fiber panels is analyzed based on the equivalent orthotropic plate model. An analysis program is developed to calculate the transmission loss of the fiber sandwich panels. Using the program, the coincidence frequency ranges and their effects on the transmission loss are investigated.

• 한국정밀공학회지
• /
• 제19권12호
• /
• pp.45-56
• /
• 2002

A pneumatic servo system requiring a fine gap control in a photo-electric sensor which is used for a LCD array detection device is introduced. The gap controlled by the pneumatic servo system remains within around 50~80 ${\mu}{\textrm}{m}$, and the system possesses an effect to eliminate undesirable particles on the LCD plate by blowing air out. The air flow rate is initially controlled by a servo valve and expanded by a booster valve, thus the controlled air pressure contributes to maintaining an appropriate gap between the LCD plate and photo-electric sensor An air floating plate of two degrees of freedom is designed and fabricated, and a fine tilting motion control is also implemented by assigning different gap commands. The pressure control and direct gap control are proposed, and each performance is verified experimentally.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.774-782
• /
• 2011

In-site Continuous Method to improve the dynamic performance of railway plater girder bridge was developed. In this study, the In-site Continuous Method in the existing railway plate girder bridge was applied. Comparison of the results obtained from the field experiment were presented. The reductions in vertical acceleration were shown to approximately 24.8%, 45.4% and 27.5% in case of the freight train, passenger train and express tilting train, respectively. The reductions of lateral acceleration were shown to approx. 31%, 39% and 15% in the previous case. In the vertical displacement, the reductions were shown to approx. 20%, 13% and 12.6%, respectively. Through this method, we expect the problem of the restriction in speed up of train to be solve.

• 비파괴검사학회지
• /
• 제29권4호
• /
• pp.283-292
• /
• 2009

Laser-based ultrasonic sensing requires the probe with fixed fecal length, but this requirement is not essential in laser-based ultrasonic generation. Based on this fact, we designed a pulsed laser-based ultrasonic wave propagation imaging (UWPI) system with a tilting mirror system for rapid scanning of target, and an in-line band-pass filtering capable of ultrasoaic mode selection. 1D-temporal averaging, 2D-spatial averaging, and 3D-data structure building algorithms were developed far clearer results allowing fur higher damage detectability. The imaging results on a flat stainless steel plate were presented in movie and snapshot formats which showed the propagation of ultrasound visible as a concentric wavefield emerging from the location of an ultrasonic sensor. A hole in the plate with a diameter of 1 mm was indicated by the scattering wavefields. The results showed that this robust UWPI system is independent of focal length and reference data requirements.

• Applied Microscopy
• /
• 제27권2호
• /
• pp.111-120
• /
• 1997

Cylinder-like crystals of $Ca^{2+}-ATPase$ provide views parallel to the lamellar plane, from which parameters of lamellar stacking can be directly measured. These parameters were measured using different preparation methods. Assuming that molecular packing is the same, data from lamellar plane could supplement those obtained by tilting large, thin plate-like crystals. However, base on data obtained .by electron microscopy and x-ray powder patterns, the plate-like crystal may have another scheme for stacking the lamellar. The projection map (h, 0, 1) from cylinder-like crystals using cryoelectron microscopy suggest the lamellar spacing can be variable.

• 한국정밀공학회지
• /
• 제8권2호
• /
• pp.78-88
• /
• 1991

The existing axial piston pump/motors of swash plate type rapidly drop efficiency in high speed region in comparison with low speed. This is the reason why the pump/motors were designed only in a view point of power supply. But, in this paper, the motor which was optimally designed on power supply load capacitancy, flow loss volume, axial stiffness and tiliting stiffness keeps up high efficiency in high speed region and in high pressure resion too.