• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.1
• /
• pp.37-46
• /
• 2014

This paper describes the conceptual design and development test procedure of a unmanned scaled-down personal air vehicle(PAV) with drive and flight dual mode capability. Trade studies on operational requirements led to the suggestion of a quad tilt prop platform which has nacelle tilt capability with multi rotor configuration. Motors for propeller propulsion and driving mechanism were integrated into a single nacelle, then they were implemented by nacelle tilt mechanism for conversion between the drive and the flight modes. Primary design parameters and initial specifications were confirmed through conceptual design, then functional tests were performed with the test platforms for the drive and the flight modes.

• Physical Therapy Korea
• /
• v.18 no.3
• /
• pp.26-37
• /
• 2011

Although there have been various studies related to the body's movement from a sitting to a standing position (sit-to-stand task), there is limited information on the kinematic changes on the frontal and transverse planes. The purpose of this study was to ascertain how pelvic tilt affects kinematic changes in the frontal and transverse planes in the hip and knee joints during a sit-to-stand task. For this study, 33 healthy participants (13 female) were recruited. Each participant rose from a sitting to a standing posture at his or her preferred speed for each of three different pelvic tilt trials (anterior, posterior, and neutral), and the measured angles were analyzed using a 3-D motion analysis system. A one-way repeated measure analysis of variance was performed with Bonferroni's post hoc test. In addition, an independent t-test was carried out to determine the sex differences in hip and knee joint kinematic changes during the sit-to-stand tasks. The results were as follows: 1) The hip and knee joint angle in the frontal and transverse planes showed a significant difference between the different pelvic tilt postures during sitting in the pre-buttock lift-off phase (pre-LO) (p<.05). Compared to the posterior pelvic tilt posture, the anterior pelvic tilt posture involved significantly greater hip joint adduction and internal rotation, knee joint adduction, and reduced internal rotation of the knee joint. 2) Sex differences were found with significant differences for males in the initial and maximal angles in the frontal plane of the hip and knee joint (p<.05). Females had a significantly smaller initial abduction angle of the hip joint and a significantly greater maximal angle of the hip adduction joint. These results suggest that selecting a sit-to-stand exercise for pelvic tilt posture should be considered to control abnormal movement in the lower extremities.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1775-1780
• /
• 2005

One of the most important factors so that mobile objects can achieve their purpose is the information about their positions. In this paper, we propose an improved beacon system, to which ultrasonic sensors are attached, for the indoor localization of mobile objects. We have researched so that it can cover the wider space and estimate more accurate positions than the existent beacon systems. The existent beacon systems have the constraint that one beacon cannot cover wide area since ultrasonic sensors have limits in the angle of signal (beam-angle) on which their signal strength depends. Hence, we used the active beacon which consists of a pan-tilt mechanism and a beacon module. The active beacon system can always aim at mobile objects in order to transmit the strongest signal of the ultrasonic sensors into the objects using the pan-tilt mechanism. In addition, this system is inexpensive because it can decrease the number of beacons by about a half of the beacons of the existent system. Finally, the results show what is the difference between the active beacon system and existent beacon systems, and how accurate it is.

• The Korean Journal of Physiology
• /
• v.30 no.2
• /
• pp.237-247
• /
• 1996

This study was carried out to determine the effect of $-6^{\circ}$ head-down bedrest on the cardiovascular and hormonal responses to orthostasis and to evaluate the mechanism of orthostatic intolerance. Ten healthy young men were changed the body position from $-6^{\circ}$ head-down or supine bedrest for 2 hr to $70^{\circ}$ head-up tilt for 20 min. During the bedrest, there were no differences in hemodynamic and hormonal changes between the head-down and the supine positions. However, the tendency of decreased end-diastolic volume and increased cardiac contractility during the later period of 2 hr showed that the cardiovascular adaptation could be accelerated within a relatively short period in the head-down bedrest. During the head-up tilt, presyncopal signs were developed in five subjects of the supine bedrest, and one of the same subjects of the head-down bedrest. In the tolerant subjects, the increase in cardiac contractility and plasma epinephrine level during the bend-up tilt was greater following the head-down bedrest than that following the supine bedrest to compensate for reduced venous return. The intolerant subjects showed the greater decrease in end-diastolic and stroke volume, and the greater increase in heart rate during the head-up tilt than the tolerant subjects. Cardiac contractility and plasma epinephrine level were remarkably increased. However, arterial pressure was not maintained at the level for the appropriate compensation of the reduced venous return. It seems that the tolerance to orthostasis is more effective after the short-term head-down bedrest than after the supine bedrest, and the secretion of epinephrine induces the higher cardiac performance as a compensatory mechanism fur the reduced venous return during the orthostasis following the head-down bedrest than the supine bedrest.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1033-1036
• /
• 2007

The optical disc drive has used a high NA objective lens and a shorter wavelength laser diode for high recording density. But high NA and shorter wavelength cause several margins to become short. Focusing and tracking servo has to be more accurate and active tilt compensation mechanism is also needed for coma aberration compensation. In this paper, we proposed 3-axis moving magnet type actuator. For 3-DOF motion, moving coil actuator has to equip 6 wires for supplying 3 independent signals. However, moving magnet type actuator doesn't need to change the configuration of wires because coils are in stator. So, we added tilting mechanism to 2-axis moving magnet actuator which is designed in previous research. Addition of the tilting mechanism cuts down the focusing sensitivity. So, maximization the tilting sensitivity and securing the focusing sensitivity are objectivities of this research. DOE (design of experiments) procedures of electromagnetic circuit are performed for parameter study and the optimization is also performed to maximize the tilt sensitivity. And then the final design is suggested and its performance is verified by FE simulation.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.2 no.3
• /
• pp.189-199
• /
• 2004

A bridge transported servo manipulator (BTSM) system for the advanced spent fuel conditioning process (ACP) has been developed to overcome the limitation of access, which is a drawback of mechanical master-slave manipulators (MSM) for the equipment maintenance. The servo manipulator is composed of a slave manipulator attached to the telescoping tubesets equipped with the overhead bridge installed at a hot cell and a master manipulator installed at an out-of-hot cell. Each manipulator has 7 degrees-of-freedom (DOF): a body rotation, an upper-arm tilt, a lower-arm tilt, a lower-arm rotation, a wrist pan & tilt, and a grasp motion. A wire-driven mechanism for a lower-arm rotation, a wrist pan and tilt, and a grasp motion of the manipulator has been adopted to increase the handling capacity compared to the manipulator weight and decrease the friction. The main disadvantage of the wire-driven mechanism is that if one link is in motion, other links can be affected. In this paper, the transmission characteristics among the wire-driven links have been formulated to overcome this drawback. The unexpected behaviors are confirmed by analyses of transmission characteristics as well as experiments. Also, the experimental results show that the unexpected behaviors are greatly decreased by the proposed compensation equations.

• Transactions of the KSME C: Technology and Education
• /
• v.1 no.2
• /
• pp.153-165
• /
• 2013

The established gait analysis studies have regarded leg as one single spring. If we can design a knee-ankle actuating mechanism as a primary actuator for supporting knee extension, it might be possible to revolutionary store or release elastic strain energy, which is consumed during the gait cycle, and as a result leg stiffness is expected to increase. An ankle joint actuating mechanism that stores and releases the energy in ankle joint is expected to support and solve excessive artificial leg stiffness caused by the knee actuator (primary actuator) to a reasonable extent. If unnecessary kinematic energy is released with the artificial speed reduction control designed to prevent increase in gait speed caused by increase in time passed, it naturally brings question to the effectiveness of the actuator. As opposed to the already established studies, the authors are currently developing knee-ankle two actuator system under the concept of increasing lower limb stiffness by controlling the speed of gait in relative angular velocity of the two segments. Therefore, the author is convinced that compensatory mechanism caused by knee actuating must exist only in ankle joint. Ankle joint compensatory mechanism can be solved by reverse-examining the change in metatarso-phalangeal joint (MTPJ) tilt angle (${\theta}_1=0^{\circ}$, ${\theta}_2=17^{\circ}$, ${\theta}_3=30^{\circ}$) and the effect of change in gait speed on knee activity.

• International Journal of Aerospace System Engineering
• /
• v.5 no.2
• /
• pp.8-15
• /
• 2018

For small earth observation satellites, alignment between the optical components is important for precise observation. However, satellite cameras are structurally subject to misalignment in the launch environment where vibration excitations and impacts apply, and in space environments where zero gravity, vacuum, radiant heat and degassing occur. All of these variables can cause misalignment among the optical components. The misalignment among optical components results in degradation of image quality, and a re-alignment process is needed to compensate for the misalignment. This process of re-alignment between optical components is referred to as a refocusing process. In this paper, we proposed a 3 - axis focusing mechanism to perform the refocusing process. This mechanism is attached to the back of the secondary mirror and consists of three piezoelectric inertia-friction actuators to compensate the x-axis, y-axis tilt, and de-space through three-axis motion. The fabricated focus mechanism demonstrated excellent servo performance by experimenting with PD servo control.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.1
• /
• pp.3-8
• /
• 2011

This paper introduces a robot eye module, of which two degree-of-freedom motions, i.e. panning and tilting, are driven by a pair of wires. The main feature of the module is that each wire can generate push-pull motion without buckling. It is thanks to a Teflon tube which guides the path of the moving wire. End points of the tube and wire have pivot elements so that a smooth push-pull motion is produced even when the end point of wire is moved by eye rotation. This mechanism helps the eye module to be very compact. In this paper, the structure of the robot eye module is introduced in detail, and the required motor angles for a certain direction of eye line are investigated analytically and experimentally.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.384-388
• /
• 2004

This study presents parametric studies for design of tiling mechanism to be used in 180km/h tilting train. The titling mechanism is composed of 4 links, a tilting bolster and an electro-mechanical actuator. First we have determined the installation height of tilting actuator using 3D tilting bogie modeling. Secondary, we verified movements of the tiling center and train body CG along variation of upper and lower span length. From this study, we obtained the upper and lower span length to minimize the lateral and vertical motion of CG of train body. Finally, we evaluated the tilting actuator force and power required to tilt the train body to $\pm$8$^{\circ}$.