• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.788-793
• /
• 2002

Hybrid type slim tilt actuator and 6-wire supported are developed for DVD recording in the optical disc drive of notebook PC, which can compensate the inclination of disc and objective lens. The hybrid actuator uses the actuating method of moving coil in the focus and track direction and that of moving magnet in the tilt direction. Comparing with 6-wire supported actuator and hybrid type actuator, we can choose an actuator for slim super combo pickup. Two actuator are designed through the modal analysis and magnetic field analysis and experimental results shows dynamic characteristics. Finally, it is verified that the actuator can compensate the disc tilt of ${\pm}0.4^{\circ}$.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.226-233
• /
• 2003

There are many researches going on to develop the information storage devices using Blue-ray disc and DVD as a demand for high-density information storage devices is highly increasing. This high-density information storage device requires a short-wave laser and objective lens of high numerical aperture set in fer its operation. And, that brings out rapid decrease of tilt tolerance. Therefore, it is necessary that an actuator should control tilt motions to get a stable signal. In this paper, a new mathematical form of 3-D.O.F coupled model is formulated and magnetic circuit in constraints is most effectively designed with the use of the moving coil type actuator in higher sensitivity. Further, this paper presents a tilt coil whose rotational center point is put on that of the lens through the variation of tilt coil and proposes a 3-axis actuator with high sensitivity improved in its dynamic property through its structure analysis.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.856-860
• /
• 2008

Wire-suspensions in the conventional actuators mechanically support the moving part and guarantee the accuracy of the actuator without tangential tilt actuation. However, such a suspension configuration has considerable stiffness in the tangential tilt direction with two additional wire beams for the tangential tilt. Thus, we performed a design sensitivity analysis for the wire-suspension stiffness of 4-axis actuator and controlled the main parameters such as distance among wire-suspensions and wire-suspension length to allow tangential tilt flexibility. The elasticity of frame PCB that supports the moving part by wire-suspensions was also exploited to improve the flexibility of wire-suspension in the tangential tilt direction. A novel suspension structure was devised by establishing eight wire-suspensions at both sides of the moving part for electrical connection to coils. The magnetic circuit according to the proposed 4-axis actuator using multi-polar magnet and coils was also suggested for the generation of electromagnetic forces in the focusing, tracking, radial and tangential tilt directions.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.378-380
• /
• 2002

There has been lower the tilt margin by the increase of coma aberration due to the reduction of wave-length and the increase of numerical aperture for high density recording. The RF signal degradation is increased as the decrease of tilt margin. To compensate the tilt margin, the optical pick-up actuator for high-speed CD/DVD re-writable system should be able to drive the radial-tilt motion. We announce that the 3-axis drive actuator for high-speed CD/DVD rewritable system. And what was more, the DC/AC sensitivities of this actuator are suitable fur the low-speed playability, the high-speed readability and the high-speed rewritability.

• 소음진동
• /
• 제10권4호
• /
• pp.584-595
• /
• 2000

We design a new actuator for high density optical device in order to control the radial tilting motion. The newly designed actuator makes it possible to control the tilting motion actively, while the coventional actuator compress tilting motion with passive spring. First of all, We present 3-dimensional modeling of actuator and accomplish the modal analysis and magnetic analysis of actuator. Due to these results, a new designed actuator has performance of high sensitivity and high second resonance frequency. Secondly, We present the 3-DOF dynamic modeling of the 4-wire spring type actuator. sensitivity analysis is performed to consider the assembling error, such as the difference of mass center and force center. From these results, the sensitivities of rotation due to the assembly error are revealed and design criteria of rotation is presented. And experimental results of a newly designed actuator are presented and compared with theoretical results. Finally, We propose a dynamic tilt compensation and high acceleration actuator for high density optical storage devices.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.782-787
• /
• 2002

In optical disk drives (ODD), the demands of high data density and high speed have been increasing rapidly to achieve high data capacity and data transfer rate. The short wavelength laser, High NA objective lens, and high track following performance are needed to raise data density and data rate. For high-performance actuator, the improvement of linearity and acceleration become more important. Also, 3-axis actuator for active tilt compensation is introduced to overcome the decrease in disk tilt tolerance which is induced by short wavelength laser. In this paper, a hybrid type 3-axis actuator is presented and a new yoke structure, which can reduce the interaction between yoke and moving magnet, is designed to keep the efficiency of magnetic circuit. Experimental results show the validity of the yoke in the hybrid type actuator.

• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.52-60
• /
• 1998

In optical disc system, 4-wire actuator has undesired tilt which degenerates the performance of RF signal. This tilt occurs from moment around the axis parallel to the tangential direction of the disk. The main reason of the moment is the coupling effect between focus driving system and tracking driving system. This paper constructed tilt mechanism and analyzed tilt quantity due to the moment based on structural analysis and magnetic field analysis. And the experiment about tilt was executed. The results were compared and discussed about the difference. Then, the design method for reducing tilt angle was suggested.

• 대한기계학회논문집A
• /
• 제29권4호
• /
• pp.624-631
• /
• 2005

A note-book PC has become thinner in recent years, which requires the optical disc drives with small height and high memory capacity. Therefore the actuator of optical disc drives must be thinner and have disc tilt compensation function for high density memory. In this paper, the actuator with hybrid type is investigated for 3-axis ultra-slim actuator. A 3-axis ultra-slim actuator is designed by using the modal analysis of the actuator and the electromagnetic analysis of magnetic circuit to achieve dynamic characteristics. Also, magnetic force between tilt magnet and tilt yoke is investigated to and the influence on the DC sensitivity in the focus and track directions.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.208-213
• /
• 2003

A note-book PC has become thinner in recent years. And optical disc drives are required to have high memory capacity. Therefore, the actuator of optical disc drives must be thinner and have disc tilt compensation function for high density memory. In this paper, the hybrid type actuator is investigated for 3-axis ultra-slim actuator. A 3-axis ultra-slim actuator is designed by using the modal analysis of the actuator and the electromagnetic analysis of magnetic circuit to achieve dynamic characteristics and magnetic flux density for high sensitivity, respectively. Also, magnetic force between tilt magnet and tilt yoke is investigated to find the influence on the DC sensitivity in the focus and track directions.

• 정보저장시스템학회논문집
• /
• 제1권2호
• /
• pp.121-126
• /
• 2005

Recently, an optical disc system has been proposed using blue laser diode, high NA objective lens and groove only disc structure. A new method is needed to readout CD and DVD in this Blu-Ray Disc Recorder. In order to readout CD and DVD in Blu-Ray Disc Recorder, we adopted dual-lenses actuator in consideration of optical utilization efficiency, optical performance and insurance of sufficient W.D(working distance). This dual-lenses actuator has two objectives in radial direction, one is for CD/DVD and the other is for BD. We had to solve the induced problems of collision between disc and lens, DC tilt increase, AC tilt increase, 2nd resonance deterioration and AC sensitivity drop caused by disposing two lenses in an actuator. Also we developed high response twin- objective actuator with radial tilt function to apply high-speed BD Recorder or BD Player. Consequently we presented that two kinds of dual-lenses actuators for BD Recorder have been possessed good performance in 3 axis directions. And we measured eye patterns of CD, DVD and BD by using one BD optical pick-up with dual-lenses actuator.