• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.2
• /
• pp.178-189
• /
• 1994

Fine $BaTiO_3$ powder was synthesized from the various starting solution with 0.05 M by ultrasonic spray pyrolysis method. The conditions of synthesis were fixed on flow rate was 0.5 cm/sec, low temperature furnace was $300^{\circ}C$, and high temperatures furnace was $700^{\circ}C$. The formation procedure was investigated directly by SEM with the collected particle from the each reaction step. Also, the trace of particle in reaction tube was researched theoretically. Fine $BaTiO_3$ was synthesized only in the case of nitrate aqueous solution. The synthesized $BaTiO_3$ powder was porous and spherical which was consist of primary particle at the size of 19.1 nm. The formation procedure was as follows : the particle size decreased in drying step and then increased in initial thermal decomposition step. Finally, particle size was decreased to $0.42 {mu}m$. The trace of particle in reaction tube was also theoretically simulated and discussed.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1084-1085
• /
• 2006

We studied formation of nanostructured $TiB_2$-Cu composites under shock wave conditions. We investigated the influence of preliminary mechanical activation (MA) of Ti-B-Cu powder mixtures on the peculiarities of the reaction between Ti and B under shock wave. In the MA-ed mixture the reaction proceeded completely while in the non-activated mixture the reagents remained along with the product . titanium diboride. The size of titanium diboride particles in the central part of the compact was 100-300 nm.

• Korean Chemical Engineering Research
• /
• v.56 no.4
• /
• pp.524-535
• /
• 2018

In this study, macroporous titania powders were synthesized utilizing the emulsion-assisted self-assembly to apply the removal of B. subtilis under UV irradiation, and the results were compared with the bactericidal effect of commercial titania nanoparticles. By changing the pore size of the porous titania powder, the reduction of B. subtilis by photocatalytic effect was measured, and the bactericidal capacity of the porous particles according to the pore size was compared in order to derive the optimum condition of the sterilization experiment. It was observed that the sterilization effect increased as the pore size became smaller, and it was confirmed that more than 50% of B. subtilis cold be removed for 1 hour of UV irradiation. Also, in order to promote the generation of active chemical species, a diluted solution of hydrogen peroxide was combined with the photocatalytic sterilization method, resulting in the removal of most of the strain after ultraviolet irradiation for 1 hour.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2004.11a
• /
• pp.77-78
• /
• 2004

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2003.10a
• /
• pp.112-113
• /
• 2003

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.97-102
• /
• 2004

용액 중에서 나노입자의 전기영동 특성을 이용한 전자종이용 잉크 제조를 위해 $TiO_2$ 나노입자를 저유전율 용매인 cyclohexane에 혼합한 후 용매와 용질의 비중차를 줄이기 위해 분말 상 polyethylen을 첨가하여 high energy milling의 방법으로 입자분쇄와 동시에 입자 표면에 고분자 풍을 코팅하였다. 용액내의 입자 분산성 향상과 용매 착색을 위하여 계면활성제와 oil-blue N을 첨가한 후 전자종이용 잉크를 제조하여 측정한 제타 전위 결과 cyclohexane 내에서 $TiO_2$의 제타전위는 -40mV 정도였으나 polyethylene으로 코팅한 후 계면활성제를 첨가하였을 경우 최대 -110mV 이상의 높은 값을 나타내었다. 실제 디스플레이 특성을 평가하기 위해 포토리소그래피를 이용하여 3인치 크기의 ITO glass 위에 $10{\mu}m$의 크기를 갖는 십자형의 격벽을 $40{\mu}m$의 높이로 균일하게 형성한 후 합성된 전자잉크로 주입하여 상부전극과 하부전극사이에 UV 경화제를 도포하여 UV 접합을 실시하였다. 격벽 내에서 입자의 mobility를 측정하여 환산된 전자잉크의 응답속도는 0.1cm/sec로 측정되었으나, 전기영동시 입자들의 움직임에 따른 반사광의 파형을 측정한 경우 0.07cm/sec의 응답속도를 나타내었다.

• Korean Journal of Materials Research
• /
• v.20 no.12
• /
• pp.669-675
• /
• 2010

One of the greatest challenges for our society is providing powerful electrochemical energy conversion and storage devices. Rechargeable lithium-ion batteries and fuel cells are among the most promising candidates in terms of energy and power density. As the starting material, $TiCl_4{\cdot}YCl_3$ solution and dispersing agent (HCP) were mixed and synthesized using ammonia as the precipitation agent, in order to prepare the nano size Y doped spherical $TiO_2$ precursor. Then, the $Li_4Ti_5O_{12}$ was synthesized using solid state reaction method through the stoichiometric mixture of Y doped spherical $TiO_2$ precursor and LiOH. The Ti mole increased the concentration of the spherical particle size due to the addition of HPC with a similar particle size distribution in a well in which $Li_4Ti_5O_{12}$ spherical particles could be obtained. The optimal synthesis conditions and the molar ratio of the Ti 0.05 mol reaction at $50^{\circ}C$ for 30 minutes and at $850^{\circ}C$ for 6 hours heat treatment time were optimized. $Li_4Ti_5O_{12}$ was prepared by the above conditions as a working electrode after generating the Coin cell; then, electrochemical properties were evaluated when the voltage range of 1.5V was flat, the initial capacity was 141 mAh/g, and cycle retention rate was 86%; also, redox reactions between 1.5 and 1.7V, which arose from the insertion and deintercalation of 0.005 mole of Y doping is not a case of doping because the C-rate characteristics were significantly better.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.368-369
• /
• 2006

By means of magnetic pulsed compaction and sintering of weakly aggregated alumina based nanopowders the jet forming nozzle samples for the hydroabrasive cutting were fabricated. The ceramics was obtained from pure alumina, as well as from alumina, doped by $TiO_2$, MgO and AlMg. It was shown that the samples sintered from AlMg doped $Al_2O_3$ powder have the best mechanical properties and structural characteristics: relative density ${\sim}0.97$, channel microhardness. - 18-20 GPa, channel surface roughness ${\sim}0.7\;{\mu}m$, average crystallite size ${\sim}1\;{\mu}m$.

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.292-300
• /
• 1997

In this study PZT powders were prepared with shapes of cubic by hydrothermal synthesis with various starting materials, and the sintering characteristics of the powders were investigated. The particle shapes were cubic regardless of starting materials, but the mean size of particles formed using $Pb(NO_3)_2$, $Ti(OC_4H_9)_4$ and $Zr(OC_4H_9)_4$ was relatively smaller than that of particles prepared from other starting materials. Agitation of the feedstock during hydrothermal reaction results in decreasing the required reaction temperature for the formation of nuclei, and in increasing the size of product particles. XRD results showed that the major phase of PZT crystal powders was a tetragonal phase at the Zr to Ti ratio of 40 to 60, or a rhombohedral phase at its ratio of 60 to 40. The density of a sintered body made from the hydrothermal powders in PbO surrounding varied with sintering temperatures and with periods of sintering time. The experimental results also showed that the optimum sintering condition was at $1150^{\circ}C$ for a 2hr sintering, and that the density of a sintered body was $7.6g/cm^3$.

• Korean Journal of Materials Research
• /
• v.5 no.6
• /
• pp.748-753
• /
• 1995

Solid solution of NaNb $O_3$70 mol% and SrTi $O_3$30 mol% was single phase. A broad dielectric peak was found at about l00K. Crystal structure was analysed at room temperature and 12K using Rietveld analysis. The unit cell was assigned to have a a doubled lattice parameter of simple perovskite sturcture at room temperatue, the structure was orthorombic with space group Pmmn. At 12K, the structure was also orthorombic with space group Pnma. This structure change with temperature was due to the distortion of oxygen octahedron. This distortion of oxygen octahedron was made by the decrease of (Ti, Nb)-O bounds length with no variation of (Ti, Nb)-O-(Ti, Nb) bound angle. Therefore the broad dielectirc peak about l00K was attributed to the structural change casued by oxygen octahedron distortion.