• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.344-349
• /
• 2005

This paper is studied on the effect of TiAlN coated ball end mill on cutting characteristic of high hardness steels in dry cutting condition without coolant. KP4 steels[HRC32] and STD11[HRC60] heat treated steels wert: used as the workpiece and WC-Co ball end mill and single and multi layer TiAlN coated ball end mill were utilized. Results showed that TiAlN coated ball end mill were increased the cutting length than WC-Co ball end mill in the cutting speed$[245\~320m/min]$ about $2\~5$ times for KP4 steels and about $2.7\~4.3$ times for STD11 heat treated steels. The multi layer TiAlN coated ball end mill is good about $1.2\~1.7$ times for KP4 steels and STD11 steels than single layer coated.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.245-251
• /
• 2004

This paper is studied on the effect of TiAlN coated Ball End Mill and MQL(Minimum Quantity Lubrication) cutting condition on cutting characteristic of high hardness steels. KP4 steels[HRC32] and STD11[HRC60] heat treated steels were used as the workpiece and WC-Co ball end mill and single and multi layer TiAlN coated ball end mill were utilized in the cutting tests. MQL device was used to spray botanical oil coolant. Result showed that TiAlN coated ball end mill were increased the cutting length than WC-Co ball end mill in the cutting speed[$245{\sim}320m/min$] about $2.3{\sim}5.7$ times for KP4 steels and about $2.5{\sim}4.3$ times far STD11 heat treated steels. The multi layer TiAlN coated ball end mill is good for KP4 steels than single layer coated.

• Tribology and Lubricants
• /
• v.17 no.6
• /
• pp.459-466
• /
• 2001

In this study, the effects of oxide layer formed on the contact parts of TiN coated ball and steel disk on friction characteristics in various sliding conditions were investigated. AISI52100 steel ball was used for the substrate of coated ball specimens, which were prepared by depositing TiN coating with 1(m in coating thickness. AISI1045 steel was used for the disk type counter-body. To investigate the effect of oxide layer on the contact parts of two materials, the tests were performed both in air for forming oxide layer on the contact parts and in nitrogen environment to avoid oxidation. From the test results, the frictional characteristic between the two materials was predominated by iron oxide layer that formed on wear tract of counter-body and this layer caused friction transition and high friction. And the adhesive wear occurred from steel disk to TiN coated ball caused the formation of oxide layer on counter parts between the two materials.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.3
• /
• pp.335-342
• /
• 2003

In this study, the effects of oxide layer formed on the contact parts of TiN coated ball and steel disk in sliding are investigated. Also wear mechanism to from the oxide layer and the characteristics of the oxide layer formation are investigated. AISI 52100 steel ball is used for the substrate of coated ball specimens. Two types of coated ball specimens were prepared by depositing TiN coating with 1 and 4 ${\mu}{\textrm}{m}$ in coating thickness. AISI 1045 steel is used for the disk type counter-body. To investigate the effect of oxide layer on the contact parts of the two materials, the tests were performed both in air for forming oxide layer on the contact parts and in nitrogen environment to avoid oxidation. And to study the effects of surface roughness of counter-body, TiN coating thickness and contact load of sliding test on the characteristics of oxide layer formation on counter-body, various tests were carried out. From the results, the friction characteristics between the two materials was predominated by iron oxide layer that formed on wear track on counter-body and this layer caused the high friction. And the formation rate of the oxide layer on wear track increased as the real contact area between the two materials increased as the contact load increased, the TiN coating thickness decreased and the surface of counter-body smoothened.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.109-116
• /
• 2001

In this study, the effects of oxide layer formed on the contact parts of TiN coated ball and steel disk in sliding are investigated. Also wear mechanism to form the oxide layer and the characteristics of the oxide layer formation are investigated. AIS152100 steel ball is used for the substrate of coated ball specimens. Two types of coated ball specimens were prepared by depositing TiN coating with 1 and 4um in coating thickness. AISI1045 steel is used for the disk type counter-body. To investigate the effect of oxide layer on the contact parts of the two materials, the tests were performed both in ambient for forming oxide layer on the contact parts and in nitride environment to avoid oxidation. And to study the effects of surface roughness of counter-body, TiN coating thickness and contact load of sliding test on the characteristics of oxide layer formation on counter-body, various tests were carried out. From the results, the friction characteristics between the two materials was predominated by iron oxide layer that formed on wear track on counter-body and this layer caused the high friction. And the formation rate of the oxide layer on wear track increased as the real contact area between the two materials increased as the contact load increased, the TiN coating thickness decreased and the surface of counter-body smoothened.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.378-384
• /
• 2000

This paper presents the results of the repeated sliding tests to determine the wear-life of TiN coated AISI 52100 bearing balls deposited by PVD method and to show the wear mechanisms of those. The sliding tests were carried out using a ball-on-disk tribometer under ambient conditions. The coefficient of friction, wear volume and the cycles to failures of TiN coated bearing balls were measured with different normal loads and roughness of lower specimens. On the wear-life diagram, the normal loads and the cycles to failure showed the good linear relation on log-log coordinate. With a decreasing normal load, the diagram showed that the wear-limits, at which the coated bearing balls survived more than 4000cycles were under 0.1N of the normal load.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.1
• /
• pp.81-86
• /
• 2010

This paper investigated into process characteristics of AlTiN coated layers for machining to the direction of upper and lower in plastic mold material (KP-4) with the cemented carbide ball endmill with the diameter of 8mm coated AlTiN layers (1~4) step by step using machining center. The material used in experiments was KP-4 that was machined by three types of inclined angles; $15^{\circ}$, $30^{\circ}$ and $45^{\circ}$ As estimated mechanical properties of AlTiN coated layers, it was shown the most result in the condition of three layered coating that the coating that the coating depth, the hardness of the coated layer and the surface roughness of the coated layer were $13{\mu}m$, Hv 3027.3 and $0.042{\mu}m$, respectively. The cutting component was better at the condition of upper direction than that of lower direction in all experimental conditions and indicated to be less which the bigger angle of the material was increased the effective diameter of the tool.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.401-405
• /
• 2001

The effects of oxide layer formed on TiN coated ball and counter-body have been investigated from the frictional point of view during sliding tests. AISI52100 steel ball was used for the substrate of coated specimens. Two types of coated specimens were prepared by depositing TiN coating with 1 and 4$\mu\textrm{m}$ in coating thickness. AISI1045 steel was used for the disk type counter-body. To investigate the effect of oxide layer on the contact parts of two materials, the tests were performed both in ambient for forming oxide layer on the contact parts and in nitrogen environment to avoid oxidation.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.179-180
• /
• 2002

In this study. the friction transition diagram based on the effect of oxide layer formation on contact surface between TiN coated steel ball and uncoated steel disk was constructed. From the diagram. it can be seen that as the contact load increases. the contact number of cycle at the beginning of oxide layer formation decreases linearly and as the coating thickness increases and the surface roughness of steel disk increases under same contact load. that increases. For the coated ball specimen, a AISI 52100 steel ball was used and AISI 1045 steel was used for the disk counter part.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.6
• /
• pp.104-110
• /
• 2008

A lot of straight bevel gears have been manufactured by the cold forging process in order to improve the productivity and mechanical property of the product. The die for the cold forging of the gear needs high precision and reproducibility. In the study, cold forging die has been modeled by CAD/CAM and manufactured by machining center using ball end mill coated by (Al, Ti)N for heat-treated alloy steel(STD11, HRC 60). Through the measurement of the machined die, satisfactory dimensional accuracy and surface roughness were obtained. In the future, many 3-d cold forging dies will be directly machined instead of electric discharge machining.