• 자원환경지질
• /
• 제12권2호
• /
• pp.79-93
• /
• 1979

한반도 내에 부존되고 있는 중적광상들은 세 주요한 Metallousenetic Epoch (Pre-Cambrian E., Jurassic-early Cretaceous E., 및 late Cretaceous-early Tertiary E.)에 생성되었고 성인으로 열수작용과 접촉교대작용에 기인된다고 보고되었다. 이중 12개 광상(달성, 산내, 일광, 상동, 대화, 월악, 복수, 옥방, 쌍전, 홍성, 삼봉, 청양)을 본 연구의 대상으로 택하고 각 지역에서 채취한 표품중 모두 25개 시료에 대하여 지화학적 실험을 수행하였다. 즉 각 분쇄된 시료 (-80+120mesh)는 super panner, 중액, isodynamic separator, UV lamp를 이용한 물리적인 처리과정을 거쳐 최종으로 입체현미경 하에서 단체분리된 후 Jarrell-Ash 1.5m Grating Spectrometer를 이용하여 본 연구대상 시료로 개발한 Spectrochemical method (Carrier: NaCl, Internal standard: $La_2O_3$)로 정량 분석되었다. 본 연구에서 밝혀낸 국내 회중석 광내에 함유되는 희유 윈소의 종류는 모두 Al, Bi, Fe, Si, Mn, Pb, Mg, Sn, Mo, Cu, Sr, Cr, Y, Ag, Ti, Ni, As, Yb의 18개 원소이며, 이들은 각각의 절대적 및 상대적인 함량과 각 광화작용의 시기, 광상의 성인, 모암, 각 원소의 mobility 그리고 회중석광의 형광색 및 육안색과 비교 검토되었다. 본 연구의 결과로 회중석광이 정출되는 과정에서 유사한 지질환경의 물리화학적인 여건이 이루어지면 그 내에 함유되는 몇 성분원소들의 화학적인 특성은 매우 유사성을 보여주는 typochemical habit를 가짐을 알 수 있었다. 본 연구에서 밝혀진 한국산 회중석 광내의 희유성분(稀有成分)으로서 Y, Mn, Sr 원소들의 Geochemical mobility의 특성(特性)은 앞으로 회중석광의 심도탐광을 위하여 고려되어야하고, 더욱 연구개발되어야 할 것이다. 또한 상기 회중석 광내의 물리적 및 화학적으로 결합되어 있는 불순물의 희유성분들은 선광 제련 파정에서 금속성분의 추출농집공정(工程)에 유용한 자료가 될 것이다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.243-243
• /
• 2010

Low-temperature grown (LTG) InGaAs epilayers were grown by MBE technique for studying a correlation between terahertz (THz) emission and the intrinsic defects. The 1.2-um-thick Be-compensated LTG-InGaAs epilayers were prepared on SI-InP:Fe substrate at $200-250^{\circ}C$, and subsequently in-situ annealed under As environment at $550^{\circ}C$ for 5-30 minutes. The carrier concentration/mobility and the crystalline structure were analyzed by the Hall effect and the x-ray diffraction (XRD), respectively, and the carrier lifetime were determined by the fs time-resolved pump-probe spectroscopy. THz generation from LTG-InGaAs was carried out by a Ti-sapphire laser (800 nm) of a pulse width of 190 fs at a repetition of 76 MHz. Figure shows the spectral amplitude of generated waves in the THz region. As the growth temperature of epilayer increases, the amplitude is enhanced. However, two samples grown at $200^{\circ}C$, as-grown and annealed, show almost no difference in the spectral amplitude. This suggests that the growth temperature is critical in the formation of defect states involved in THz emission. We are now investigating the correlations between the XRD band attributed to defects, the Hall parameter, and the spectral amplitude of generated THz wave.

• 한국물환경학회지
• /
• 제25권4호
• /
• pp.522-529
• /
• 2009

To supply safe drinking water to areas lacking in water supply and drainage system, such as rural area and military bases in proximity to Demilitarized Zone, effective method for treating organic contaminants such as MTBE is required. This study focuses on seeking optimal conditions for effective degradation of MTBE using a bath type ultrasound reactor. Effectiveness of MTBE degradation by ultrasound is dependent on the frequency, power, temperature, treatment volume, initial concentration, catalyst, etc. In this study the degradation rate of MTBE by ultrasound was proportional to power/unit volume ratio and removal is relatively more efficient for 0.1 mM than for 1 mM of MTBE solution. Efficiency of ultrasound treatment for 1 mM MTBE solution was enhanced under bath temperature of $30^{\circ}C$ compared to $4^{\circ}C$, but the temperature effect was negligible for 0.1 mM MTBE solution. Also for 0.1 mM MTBE solution, effect of catalyst such as $TiO_2$ and $Fe^0$ on treatment speed was negligible, and zeolite even increases the time taken for the degradation. Under these specific experimental conditions of this study, the most determinant factor for degradation rate of MTBE in solution was frequency and power of ultrasound. The results have shown that a continuous ultrasound reactor system can be used for small scale remediation of organically polluted groundwater, under optimal conditions.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.129-129
• /
• 2018

Hard coating application is effective way of cutting tool for hard-to-machine materials such as Inconel, Ti and composite materials focused on high-tech industries which are widely employed in aerospace, automobile and the medical device industry also Information Technology. In cutting tool for hard-to-machine materials, high hardness is one of necessary condition along with high temperature stability and wear resistance. In recent years, high-entropy alloys (HEAs) which consist of five or more principal elements having an equi-atomic percentage were reported by Yeh. The main features of novel HEAs reveal thermodynamically stable, high strength, corrosion resistance and wear resistance by four characteristic features called high entropy, sluggish diffusion, several-lattice distortion and cocktail effect. It can be possible to significantly extend the field of application such as cutting tool for difficult-to-machine materials in extreme conditions. Base on this understanding, surface coatings using HEAs more recently have been developed with considerable interest due to their useful properties such as high hardness and phase transformation stability of high temperature. In present study, the nanocomposite coating layers with high hardness on WC substrate are investigated using high entropy alloy target made a powder metallurgy. Among the many surface coating methods, reactive magnetron sputtering is considered to be a proper process because of homogeneity of microstructure, improvement of productivity and simplicity of independent control for several critical deposition parameters. The N2 is applied to reactive gas to make nitride system with transition metals which is much harder than only alloy systems. The acceleration voltage from 100W to 300W is controlled by direct current power with various deposition times. The coating layers are systemically investigated by structural identification (XRD), evaluation of microstructure (FE-SEM, TEM) and mechanical properties (Nano-indenter).

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.131-131
• /
• 2018

최근 절삭공구산업은 자동차, 항공기, IT, 선박, 에너지 등 첨단산업의 증가로 인해 CGI, CFRP, 내열합금 등 난삭재의 수요가 증가하고 있다. 난삭재는 고내열, 고경도, 초경량 같은 특성을 지니며 우수한 기계적 물성을 갖지만 가공의 어려움이 있어 산업에 적용하는데 한계가 있다. 이러한 한계를 극복하기 위해 개발된 가공기술 중 하드 코팅은 공구코팅비용 대비 공구의 표면경도와 수명을 효율적으로 향상시킬 수 있다고 알려져 있다. 대표적인 하드코팅으로는 AlN계, TiN계 코팅이 있다. 이러한 코팅의 경우 높은 기계적 물성과 우수한 내마모성으로 인해 절삭공구의 성능을 향상시킬 수 있기 때문에, 많은 연구가 진행되고 있으며 절삭공구산업에서 각광받고 있다. 기존 선행연구 결과에 따르면 질화물 코팅의 우수한 물성은 질화물(Nitride) 생성 및 질화 공정에 의한 코팅층의 고밀도화에 의해 나타난다고 알려져 있다. 그 중에서 AlCrN coating은 우수한 내마모성 및 향상된 고온경도를 갖고 있다. AlCrN based coating에 미량의 원소를 첨가하여 기존 AlCrN coating의 기계적 특성을 더욱 향상 시킨 coating은 일반적인 고성능 코팅 대비 공구수명이 길다고 알려져 있으며, 전반적으로 우수한 특성에 의해 전 세계적으로 습식 및 건식 기계 가공 용도로 사용되고 있다. 본 연구에서는 AlCrN based coating에 미량의 원소를 첨가한 coating의 우수한 기계적 특성의 원인을 규명하기 위해 텅스텐카바이드(WC) 기판 위에 아크 이온 플레이팅 장비를 이용하여 AlCrN based coating을 증착 시킨 sample을 분석하였다. 결정구조 및 상 분석을 위해 X선 회절분석(XRD)을 실시하였으며, 미세 구조를 분석하기 위해 전계방출형 주사전자현미경(FE-SEM), 투과 전자현미경(TEM) 분석을 실시하였다. 또한 코팅층의 화학적 성분 분석을 위해 EDX분석을 실시하였으며 기계적 특성 평가를 위해 나노압입시험(Nano-indentation test)을 진행하였다.

• 한국염색가공학회지
• /
• 제29권3호
• /
• pp.171-179
• /
• 2017

This study was to investigate the practicality and functionality of water lily(Nymphaea tetragona) leaves as a natural dye resource while searching for various dyeing methods to utilize them. Effect of dyeing condition including methanol ratio of dyebath, dyeing temperature and time, mordanting method, etc were investigated. Colorants were prepared by extraction in methanol and followed drying process. When composing 30% of methanol in the dyebath, better dyeuptake and uniform dyeing were resulted. Pre-mordanting method gave better results in terms of dye uptake than post-mordanting method on the wool fabrics. Fe and Ti were effective for increasing the dye uptake on the silk fabrics. Depending on mordant type and mordanting method, the dyed fabrics got various color showing green, khaki, brownish yellow, dark brown, dark gray and so on. As for color fastness, the silk fabrics dyed with water lily extract showed relatively high rating in light fastness(3~4, 4~5 rating), washing fastness(4~5, 5 rating), and rubbing fastness(4, 4~5 rating). The silk and wool fabrics dyed with water lily leaves extract showed excellent antimicrobial activity over 98% of bacterial reduction rate against Staphylococcus aureus and Klebsiella pneumoniae. It was confirmed that water lily leaves can be used as a natural dye resource for dyeing wool and silk fabrics because its colorants showed excellent affinity and antimicrobial functionality as well as good colorfastness.

• 한국대기환경학회지
• /
• 제16권1호
• /
• pp.11-22
• /
• 2000

Polycyclic aromatic hydrocarbons(PAHs) have known as potentially hazardous air pollutants(HAPs0 to human health because of its carcinogenic and mutagenic behaviors. The purpose of this study was to determine the level of 6 PAHs(Fluoranthene, Pyrene, Benzo[a]anthracene, Chrysene, Benzo[b]fluoranthene, and Benzo[a]pyrene) as well as 10 inorganic elements(Cr, Na, K, Zn, Pb, Fe, Cu, Ti, Al and Cd) in the ambient PM-10. The total of 115 samples had been collected from February, 1996 to June, 1996 on quartz fiber by a PM-10 high volume air sampler near the Yong-Tong Apartment complexes. A statistical analysis was performed for the PAHs and inorganic elements data set using a principal component analysis in order to identify qualitatively the potential sources of PM-10. A total of 6 principal components were separated by intensive data pretrement and transformation processes, such as soil, refuse incineration, oil burning, coal burning, field burning, vehicle emission sources. The results showed that PAHs were associated with various burning activities like refuse and field burning, coal burning, and oil burning emissions in the study area. These derived sources were well matched with the previously known source profiles in terms of compositonal order and level of measured species. The combination data set consisted of both organic and inorganic species might provide more powerful source signature and might increase the number of potentially derived sources than PAHs or inorganic data alone.

• 동굴
• /
• 제21권22호
• /
• pp.17-56
• /
• 1990

Cheju Island, which was formed by volcanic activity, is an oval in its shape with the major axis of 80km and the minor axis of 40km. The island holds in its heart Mt. Hanla rising 1,950m above the sea. Petrological study of this volcanic island has been made actively by Sang-Man Lee, Chong-Kwan won and Moon-Won Lee. The chronological measurements of the island by Chong-Kwan Won and Moon-Won Lee showed that it is composed of Sanbangsan trachytes and Backlokdam trachytes(25,000 year ago). These reports are based on the chemical analysis and the rediometric chronological measurements on the ground. However, there has been no reports about the inside of caves. We made an (composition) analysis of the inside of Manjang Cave by the fundamental parameter method in X-ray fluorescence spectrometry. The fundamental parameter method in X-ray fluorescence spectrometry is nondestructive analysis, and it enables us to make the values processed by a computer. The results obtained by this methods are as follows : SiO$_2$(49％), $Al_2$O$_3$(17％), Fe$_2$O$_3$(13％), CaO(8.1％), MgO(5.5％), Na$_2$O(3.6％), TiO$_2$(2.1％), $K_2$O(0.86％), P$_2$O$_{5}$(0.28％), and MnO(0.20％), respectively. The data obtained by the fundamental parameter method in X-ray fluorescence was compared with the data provided by Chong-Kwan and Moon-Won Lee. Our measurement was made by K-Ar-method in cooperation with T.ITAYA. The samples are of 30,000～420,000 year ago. The composition of the values of our underground analysis with the existing values obtained by the analyses on the ground produced new data about Cheju volcanic island.d.

• 한국자원식물학회지
• /
• 제17권2호
• /
• pp.161-168
• /
• 2004

Ferritin light heavy chain (FLHC) gene는 일부 중금속과 결합, 저장 및 운반하여 무독화 시킬 수 있는 것으로 알려져 있다. Fe 관련 유전자인 FLHC유전자를 식물 발현용 promoter인 35S promoter와 Tnos를 사용하여 식물 형질전환용 vector를 재조합하였다. 식물세포형질전환용 binary vector는 상기 cassette vector가 조립이 매우 양호하며 border sequence를 가지고 있는 pRD400 binary vector를 사용하여 최종적으로 가나마이신 내성 유전자 (NPT II gene)와 tadpole ferritin heavy chain gene 및 human ferritin light chain gene를 함유하고 있는 binary vector를 재조합하였다. Binary vector의 아그로박테리움에 도입은 triparental mating 방법에 의하여 수행하여 AB배지 및 가나마이신 함유 배지에서 disarmed Ti-vector를 가지고 있는 Agrobacterium tumefaciens MP90/FLHC을 선발하였다. FLHC 유전자 도입된 식물형질전환용 binary vector를 이용하여 형질전환방법을 변형하여 많은 embryo를 유도하였으며 유도된 embryo들은 GA 10mg/L가 첨가된 배지에 지상부를 유도하였다. 형질전환체식물체의 정상적인 생장을 유도하기 위해 최적의 배양조건을 조사하였던 바, 비교적 1/3 MS배지에서 뿌리의 생장과 지상부의 생장이 균일하게 생장하는 경향을 보였으며, 뿌리와 줄기가 잘 발달된 약 7cm의 유식물체를 대량으로 증식하여, 모래와 흙이 1:1로 혼합된 토양에 옮겼다.

• 대한의용생체공학회:의공학회지
• /
• 제6권1호
• /
• pp.37-46
• /
• 1985

Development of a dental Ni-Cr alloy system for porcelain veneering crown and bridge was studied in this research. The principles of alloy design were a) It should not contain toxic beryllium. b) It should have low melting Point. c) It should be easily ground and polished. d) It should possess an adequate strength to resist the deformational force In the mouth. e) It should be bondable Ivith porcelain by chemically. After investigating the effect of minor elements such as boron and rare earth metals on the mechanical properties of the Ni-Cr alloy system, the compromised ideal composition for dental use was determined. The composition was l9.6%, Cr, 5.6% Mo, 3.4% Si, 1, 0% Fe, 0.01% Ti, 0.5-1.0% B, 0.2-0.6% misch metal, balance Ni. To compare the performance of experimental alloy with commercially available alloys, the properties such as strength, melting point, and bond strength were measured. The results Ivere as follows: a) Boron increases the strength of the alloy but reduces the elongation. b) Misch metal increases the strength when the boron content is low, but does not increase the strength when boron content is high. And it reduces the elongation drastically, c) Mechanical strength of the experimental alloy was not superior to commercially available Be containing alloy, but handling performance such as castability, ease of granting and polishing, and cuttability were superior to the Be containing alloy.