• 한국결정성장학회지
• /
• 제12권1호
• /
• pp.36-41
• /
• 2002

$H_2$(5%)/Ar의 환원분위기에서 $900^{\circ}C$ 이상의 온도로 소결함으로써 화학양론적인 조성비를 만족하면서 이중 페롭스카이트 구조를 갖는 $Sr_2FeMoO_6$ (SFMO) 소결체를 제조하였다. SFMO 소결체는 우수한 강자성 특성을 나타내었고 8K에서 15%와 상온에서 3% 정도의 자기저항비를 나타내었다. 이 SFMO 소결체를 타겟으로하여 스퍼터링법으로와의 단결정 기판 위에 비정질 SFMO 박막을 증착한 후, 적절한 H$_2$(5%)/Ar의 환원분위기, $680^{\circ}C$ 이상) 열처리 조건의 고상결정법으로 이중 페롭스카이트 구조의 다결정 SFMO 박막을 제조하였다. 이 SFMO 박막은 강자성 특성을 잘 나타내었으나, 자기저항 특성은 상온에서는 나타나지 않았고 8K에서 약 0.3-0.5%의 자기저항비를 나타내었다. 이와같이 박막의 경우 자기저항 특성이 떨어지는 이유는 제조된 SFMO 박막이 화학양론비를 만족하지 못하고 조직의 치밀도가 떨어져서 결정립 사이에서 발생하는 자기스핀 터널링이 제대로 발생하지 못하였기 때문이라 생각되었다.

• Ocean and Polar Research
• /
• 제26권2호
• /
• pp.231-243
• /
• 2004

Sequential extraction was carried out on twenty two subsamples of three ferromanganese crusts from three seamounts (Lemkein, Lomilik, and Litakpooki) near the Marshall Islands in the western Pacific. The extraction was designed to fractionate Fe-Mn crust forming elements into low defined groups: (1) exchangeable and carbornate, (2) Mn-oxide, (3) Fe-oxyhyd.oxide, and (4) residual fraction. X-ray diffraction result shows that target material were well removed by each extraction step except for CFA in phosphatized crusts generation. According to chemical analysis of each leachate, most of elements in the Fe-Mn crusts are bound with two major phases. Mn, Ba, Co, Ni, Zn, (Fe, Sr, Cu, and V) are strongly bounded with Mn-oxide $({\delta}-MnO_2)$ phase, whereas Fe, Ti, Zr, Mo, Pb, Al, Cu,(V, P, and Zn) show chemical affinity with Fe-oxyhydroxide phase. This result indicates that significant amount of Al, Ti, and Zr can not be explained by detrital origin. Ca, Mg, K, and Sr mainly occur as exchangeable elements and/or carbonate phase. Outermost layer 1 and inner layer 2 which are both young crusts generations are similar in chemical speciations of elements. However, some of Fe-oxyhydroxide bounded elements (Pb, Y, Mo, Ba, Al, and V) in phosphatized innermost layer 3 are released during phosphatization and incorporated into phosphate (Pb, Y, Mo, and Ba) or Mn-oxide phase (Al and V). Our sequential extraction results reveal that chemical speciations of elements in the hydrogenetic crusts are more or less different from interelemental relationship calculated by statistical method based on bulk chemistry.

• 한국분말재료학회지
• /
• 제14권4호
• /
• pp.230-237
• /
• 2007

The fabrication of Fe alloy-40 wt.%TiC composite materials using spark plasma sintering process after ball-milling was studied. Raw powders to fabricate Fe alloy-TiC composite were Fe alloy, $TiH_{2}$ and activated carbon. Fe alloy powder was Distaloy AE (4%Ni-1%Cu-0.5%Mo-0.01%C-bal.%Fe) made by Hoeganes company with better toughness and lower melting point. These powders were ball-milled in horizontal attrition ball mill at a ball-to-powder weight ratio of 30 : 1. After that, these mixture powders were sintered by using spark plasma sintering apparatus for 5 min at $1200-1275^{\circ}C$ in vacuum atmosphere under $10^{-3}$ torr. DistaloyAE-40 wt.%TiC composite was directly synthesized by dehydrogenation and carburization reaction during sintering process. The phase transformation of as-milled powders and sintered materials was confirmed using X-ray diffraction (XRD) and transmission electron microscope (TEM). The density and harness materials was measured in order to confirm the densification behavior. In case of DistaloyAE-40 wt.%TiC composite retained for 5 min at $1275^{\circ}C$, it has the relative density of about 96% through the influence of rapid densification and fine TiC particle reinforced Fe-based composites materials.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1030-1031
• /
• 2006

Titanium alloys and Titanium alloy-based particulate composites were synthesized using the blended elemental P/M route. First, processing conditions such as the fabrication of master alloy powder were investigated. Ti-6Al-4V, Ti-5Al-2.5Fe, Ti-6Al-2Sn-4Zr-2Mo, IMI685, IMI829, Timetal 1100 and Timetal 62S, and Ti-6Al-2Sn-4Zr-2Mo/ 10%TiB and Timetal 62S/10%TiB were then synthesized using the optimal processing conditions obtained. The microstructures and mechanical properties such as tensile strength and high cycle fatigue strength were evaluated.

• 한국전자현미경학회:학술대회논문집
• /
• 한국현미경학회 2000년도 제31차 추계학술대회
• /
• pp.52-55
• /
• 2000

• 열처리공학회지
• /
• 제13권6호
• /
• pp.412-419
• /
• 2000

There has been a considerable attention on Invar alloys due to its low thermal expansion property. A low thermal expansion property of Invar alloys, lower than $10^{-6}$ near the room temperature, is attractive for electric transmission lines and precision machine tools. However, the expansion property of Invar alloys is limited below about 520K, and mechanical properties are relatively low to apply to electric transmission line. In order to improve mechanical properties in this alloy, Ti alloying element was added to the $Ni_{38}-Mo_2-Cr_1-Fe$ invar alloy. The microstructure Ti added alloy showed finer than that of the unalloyed one. It was found that the (Mo, Ti), Mo carbide formed by Ti addition obstacled grain growth by pinning effect and supplyed recrystallization sites during heat-treatment. Optimum heat-treatment conditions with Ti addition were also discussed in the modified Invar alloy.

• 한국표면공학회지
• /
• 제37권1호
• /
• pp.1-4
• /
• 2004

MoS$_2$-Ti films were deposited on SKD-11 tool steel substrate by a D.C. magnetron sputtering system. The influence of deposition parameters on the adhesion of the films was investigated by the scratch test. Crosssection morphology was evaluated using FE-SEM. The plasma etching played an important role on the adhesion of the films. The appropriate etching conditions roughened the surface, resulting In the improved adhesion of the film. The adhesion of the film increased with the interlayer thickness up to 110 nm and then decreased slightly with further increasing of interlayer thickness. The adhesion was highest at a bias voltage of -50 V. Further increase of the bias voltage decreased the film adhesion.

• 한국자기학회지
• /
• 제12권3호
• /
• pp.94-98
• /
• 2002

20nm이하의 얇은 박막에서도 높은 보자력이 요구되는 Ti/CoCrPt 수직자기기록박막의 보자력 향상을 위해 Al, Cu, Ni, Cr, Ag, Mg, Fe, Co, Pd, Au, Pt, Mo, Hf등의 여러 하지층과 제조조건이 보자력에 미치는 영향을 조사하였다 이들 중 Ag과 Mg하지층은 Ti/CoCrPt박막의 보자력을 향상시켰으며 특히 2nm Ag 하지층을 사용할 경우 10nm CoCrPt 박막에서 2200 Oe의 높은 보자력을 보일뿐 아니라 $\alpha$값을 낮추는 효과가 있었다. 그러나 Ag를 하지층으로 사용하면 기대와는 달리 Ti(002)면의 우선배향 성장이 전혀 일어나지 않아 보자력 증대에 다른 기구가 작용하는 것으로 판단되었다. 그리고 표면의 거칠기가 큰 기판에서는 보자력뿐만 아니라 역자구생성자계도 감소하였다.

• Nuclear Engineering and Technology
• /
• 제31권6호
• /
• pp.595-607
• /
• 1999

The reaction cross-sections of $^{nat}$Ti(p,X)$^{48}$ V, $^{nat}$Fe(p,X)$^{56}$ Co, $^{nat}$Cu(p,X)$^{65}$ Zn and $^{nat}$Mo(p,X)$^{96}$ Tc for TLA application are calculated in the frame of the ECIS-GNASH code system up to 60 MeV. The calculated results are compared with the experimental data taken from the EXFOR at the NEA Data Bank. A preliminary calculation with the global optical parameters of Varner et al. shows considerable differences from the experimental data at low energy range. The global optical parameters for the imaginary volume potential and the diffuseness of the imaginary potential are adjusted to achieve a better description of the experimental data in the vicinities of peak position below 16 MeV. 16 MeV.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.104-105
• /
• 2006

The low-cycle fatigue performance and fracture of the P/M Ti-Fe-Mo-Al-Nd Alloys after sintering and forging have been studied. The linear regression equation of low-cycle fatigue lifetime has been obtained; the fatigue performances are objected under two different conditions. The fatigue fracture surface is analyzed by SEM. The low-cycle fatigue behavior of the P/M titanium alloy has been discussed.