• 폴리머
• /
• 제35권1호
• /
• pp.40-46
• /
• 2011

The synthesis of well-defined poly(styrene-b-isobutylene-b-styrene) (SIBS) triblock copolymers was accomplished by cationic sequential block copolymerization of isobutylene (IB) with styrene (St) using 1,4-di(2-chloro-2-propyl) benzene (DCC) /$TiCl_4$/2,6-di-tert-butylpyridine(DtBP) as an initiating system in methyl chloride ($CH_3Cl$)/methylcyclohexane(MeChx) (50/50 v/v) solvent mixture at $-80^{\circ}C$. The triblock copolymers exhibited excellent thermoplastic and elastomeric characteristics. Tensile strengths and Shore hardness increased with increasing polystyrene (PS) content, while elongation at break decreased. The blood-compatibility of SIBS was assessed by SEM observation of the platelet adhesion, blood clotting time and haemolysis ratio. The haemolysis ratios were below 5% which met the medical materials standard. The platelet adhesion test further indicated that SIBS block copolymers had a good blood compatibility.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.870-874
• /
• 2000

This investigation reports the grinding characteristics of titanium alloy(Ti-6Al-4V). Grinding experiments were performed at various grinding conditions and the grinding forces and specific grinding energies were measured to investigate the grindability of titanium alloy with the three different wheels including Diamond, Green carbide and Alumina. To investigate the grinding characteristics of titanium alloy grinding force, force-ratio, specific grinding energy and grinding -ratio, were measured. Surface roughness was also measured with tracer and the ground surfaces were observed with SEM. Force-ratio of grinding of titanium alloy was very lower than that of grinding of SKD-11. Specific grinding energy are almost five times larger and rougher surface was obtained in titanium grinding.

• 자원환경지질
• /
• 제42권3호
• /
• pp.177-193
• /
• 2009

삼광광상은 선캠브리아기 경기육괴의 화강편마암내에 발달된 단열대(NE, NW)를 따라 충진한 8개의 괴상맥으로 구성된 중열수 석영맥광상이다. 이 광상의 광화작용은 여러번의 단열작용에 의해 형성된 두시기의 석영+방해석시기(광화I시기)와 방해석시기(광화II시기)로 구성된다. 광화I시기의 열수작용에 의한 변질작용은 견운모화, 녹니석화, 탄산염화, 황철석화, 규화, 및 점토화작용등이 관찰되며 견운모대는 석영맥과 접촉한 부분에서 녹니석대는 석영맥으로부터 멀어짐에 따라 관찰된다. 견운모대의 모암변질광물은 대부분이 견운모 및 석영이며 일부 일라이트, 탄산염광물, 녹니석으로 구성된다. 녹니석대의 모암변질광물은 주로 녹니석, 석영과 소량 견운모, 탄산염광물 및 녹염석으로 구성된다. 견운모의 Fe/(Fe+Mg) 값은 0.45${\sim}$0.50(0.48$\pm$0.02)이며 백운모-펜자이트족에 해당되고 녹니석의 Fe/(Fe+Mg) 값은 0.74${\sim}$0.81(0.77$\pm$0.03)이고 대부분 브런스비자이트에 해당된다. 견운모와 녹니석에 대한 $Al_{IV}$-FE/(FE+Mg)의 다이어그램은 변질시 같은 광종의 견운모와 녹니석의 형성온도를 나타내는 지시자로써 유용하다. 이것은 계산된 녹니석 단종의 활동도가 $a3(Fe_5Al_2Si_3O_{10}(OH)_6$=0.0275${\sim}$0.0413, $a2(Mg_5Al_2Si_3O_{10}(OH)_6$=1.18E-10${\sim}$7.79E-7, $a1(Mg_6Si_4O_{10}(OH)_6$=4.92E-10${\sim}$9.29E-7로서 삼광광상의 녹니석은 iron-rich 녹니석으로 비교적 고온 (T>450$^{\circ}C$에서 모암과 평형상태에서 온도가 감소함에 따라 형성되었음을 알 수 있다. 모암변질시 ${\alpha}Na^+$, ${\alpha}K^+$, ${\alpha}Ca^{2+}$ 및 ${\alpha}Mg^{2+}$는 각각 ${\alpha}Na^+$=0.0476($400^{\circ}C$), 0.0863($350^{\circ}C$), ${\alpha}K^+$=0.0154($400^{\circ}C$), 0.0231($350^{\circ}C$), ${\alpha}Ca^{2+}$=2.42E-11($400^{\circ}C$), 7.07E-10($350^{\circ}C$), ${\alpha}Mg^{2+}$=1.59E-12($400^{\circ}C$), 1.77E-11($350^{\circ}C$)이며 열수용액의 pH는 5.4${\sim}$6.4($400^{\circ}C$), 5.3${\sim}$5.7($350^{\circ}C$)로서 모암변질시 열수용액는 약산성이었음을 알 수 있다. 모암변질시 이득원소(부화원소)는 $TiO_2$, $Fe_2O_3(T)$,CaO, MnO, MgO, As, Ag, Cu, Zn, Ni, Co, W, V, Br, Cs, Rb, Sc, Bi, Nb, Sb, Se, Sn 및 Lu 등이며 특히 대부분의 광상에서 Ag, As, Zn, Sc, Sb, S,$CO_2$ 등의 원소가 현저하게 증가하므로 중열수 및 천열수 금-은광상의 탐사에 지시원소로서 활용될 수 있을 것이다.

• 대한금속재료학회지
• /
• 제48권7호
• /
• pp.589-597
• /
• 2010

In the present study, the effect of variation in alloying elements on the carbide formation behavior during casting and homogenization treatment of M2 high speed steels was investigated. M2 high speed steels of various compositions were produced by vacuum induction melting. Contents of C, Cr, W, Mo, and V were varied from the basic composition of 0.8C, 0.3Si, 0.2Mn, 4.0Cr, 6.0W, 5.0Mo, and 2.0V in weight percent. Homogenization treatment at $1150^{\circ}C$ for 1.5 hr followed by furnace cooling was performed on the ingots. Area fraction and chemical compositions of eutectic carbide in as-cast and homogenized ingots were analyzed. Area fraction of eutectic carbide appeared to be higher in the ingots with higher contents of alloying elements the area fraction of eutectic carbide also appeared to be higher on the surface regions than in the center regions of ingots. As a result of the homogenization treatment, $M_2C$ carbide, which was the primary eutectic carbide in the as-cast ingots, decomposed into thermodynamically stable carbides, MC and $M_6C$. The latter carbide was found to be the main one after homogenization. Fine carbides uniformly distributed in the matrix was found to be MC type carbide and coarsened by homogenization.

• 암석학회지
• /
• 제16권4호
• /
• pp.217-232
• /
• 2007

푸우오오 용암분출은 1983년에 분출이 시작된 이래 현재까지 활동하고 있으며, 다양한 성분 변화와 ($5.6{\sim}10.1wt.%$ MgO), 지표분출 면적을 가지는(${\sim}2km^3$) 하와이의 역사적인 분출 중에 하나이다(Garcia et al., 1999). 다년간에 걸쳐 하와이 분출에 대한 연구가 수행되어 왔으나, 최근 수년 이내에 분출된 푸우오오 용암의 지질학적인 특성에 대한 연구 결과의 부재와 푸우오오 분출 역사를 통한 하와이 마그마 분출과정의 특성을 파악하고자 시공간적으로 채취한 시료를 바탕으로 광물과 암석의 조직과 화학조성연구를 수행하였다. 박편 상에서 단사휘석이나 사장석 반정은 드물고 감람석이 대부분의 반정을 차지한다. 이것은 푸우오오 지역이 마그마 분화 초기단계에 머물러 있다는 것을 지시한다. MgO를 상대로 주원소에 대해 도시해 본 결과 MgO가 증가함에 따라 $TiO_2,\;Al_2O_3,\;Na_2O,\;SiO_2$는 감소하는 경향을 보인다. 미량원소의 경우 $K_2O$값에 대한 Zr, Y, Sr 그리고 V 도표에서 P18과 P19시료가 타 용암에 비해 진화가 더 진행된 영역에 도시되고 있다. 2003 년에서 2006년 분출년도 간에 높은 Ni 함량이 나타나는데, 이것은 동일 기원마그마의 유입에 의한 결과이다.

• Journal of Oral Medicine and Pain
• /
• 제20권2호
• /
• pp.429-447
• /
• 1995

This study was designed to determine the most effective concentration of fluoride and levels of laser irradiation for the remineralization of decayed teeth. After irradiation with a pulsed Nd:YAG laser and the topical application of fluoride, phosphate and fluoride concentration in enamel were measured. And then the changes on surface enamel using an scanning electron microscope were observed. Samples by extraction healthy, permanent, mandibular bovine teeth with no caries were obtained. Among them 371 healthy samples were selected and artificial carious lesions were made. 20 samples were assigned to each experimental group. After irradiation with a pulsed Nd:YAG laser with total energy densities of 10J/$\textrm{cm}^2$, 20J/$\textrm{cm}^2$ for each group. On the teeth, 2% NaF, 1.9% NH4F, 1.6% TiF4 Elmex gel(amine fluoride) and 1.23% APF gel were applied. After pH circulatory procedures, concentrations of fluoride with and Ionalyzer (Orion Research, Model 901, USA) and phosphates with an Uv/V is spectrophotometer (Uvikon 860, Kontrom Co, Switzerland) were measured. By etching the teeth in layers and measuring fluoride concentrations, a profile of fluoride penetration according to depth could be developed. And also the changes on the surface of the enamel using an electron scanning microscope were observed. The comparative analysis yielded the following results : 1. Phosphate concentration was low in all groups compared with the control group except for teeth treated Elmex gel, irradiated with 10J/$\textrm{cm}^2$ and 30J/$\textrm{cm}^2$ energy densities. Teeth treated with APF gel and 30J/$\textrm{cm}^2$ irradiation gad the lowest phosphate concentration. 2. Among all groups, fluoride concentrations in tooth enamel were highest in APF gel and NaF groups irradiated at 30J/$\textrm{cm}^2$. The APF gel group had the highest fluoride concentrations across all energy densities. 3. In the APF gel group, and the NaF group, the greater the energy density of the laser, the higher the fluoride concentrations in the enamel. 4. In all groups, the concentration of fluoride in the enamel by depth tended to decrease with depth. 5. Under the scanning electron microscope, under the condition of irradiation with 20J/$\textrm{cm}^2$, enamel crack was detected for the first time. In the NH4F group, spherical deposits were found on the surface of the enamel, and in the TiF4 group the surface of enamel was covered with an irregular, thin membranous mass in places. In the APF gel and NaF groups irradiated with 10J/$\textrm{cm}^2$, spherical and irregular particles covered the teeth. When these groups were irradiated at 20J/cm2, they were covered with amorphous crystals. These results suggest that one could obtain more effective anticariogenic effects without damage to teeth when less than 20J/$\textrm{cm}^2$ energy densities and APF gel are used.

• 한국기계가공학회지
• /
• 제3권1호
• /
• pp.72-78
• /
• 2004

In this paper, mechanical behaviors of developed pedicle screw system, made of bio-mechanical materials(Ti-6Al-4V, Grade 5), ale predicted using FEM analysis. As a first step, morphologic construction of normal Korean spines and surgical operation convenience are considered to design optimum pedicle screw system. In this step, various design variables are considered as design parameters to develop optimized models. As a next step, tension and bending tests are performed to improve the structural performance of the developed system using finite element method. In this step, required Static compression and bending test specifications by ASTM F-04 25 04 01 are applied to understand the bio-mechanical behaviors of the designed spinal implant system under various load types. As the results of this research, it is possible to develop efficient pedicle screw system, having enough rigidity and fixation to stand any spinal damage under allowable stress conditions.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.111-120
• /
• 2014

The aim of this study is to develop an integrated urea-SCR catalytic filter system for reducing soot and $NO_X$ emissions simultaneously in diesel engines. In this study, the characteristics of exhaust emissions relative to reactive activation temperature under four kinds of engine loads are experimentally investigated by using a four-cycle, four-cylinder, direct injection type, water-cooled turbo intercooler ECU common-rail diesel engine with the integrated urea-SCR $MnO_2-V_2O_5-WO_3/TiO_2/SiC$ catalytic filter system operating at three kinds of engine speeds. The urea-SCR reactor is used to reduce $NO_X$ emissions, and the catalytic filter system is used to reduce soot emissions. The reactive activation temperature is very important for reacting a reducing agent with exhaust emissions. The reactive activation temperatures in this experiment is applied to 523, 573 and 623 K. The fuel is sprayed by the pilot and main injections at the variable injection timing between BTDC $15^{\circ}$ and ATDC $1^{\circ}$ according to experimental conditions. It is found that the $NO_X$ conversion rate is the highest as 83.9% at the reactive activation temperature of 523 K in all experimental conditions of engine speed and load, and the soot emissions shown by the average reduction rate of approximately 93.3% are almost decreased below 0.6% in all experimental conditions regardless of reactive activation temperatures. Also, the THC and CO emissions by oxidation reaction of Mn, V and Ti are shown in the average reduction rates of 70.3% and 38% regardless of all experimental conditions.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.117-117
• /
• 2016

Total ankle replacement (TAR) is a visible option in the surgical treatment of degenerative or inflammatory diseases of ankle joint. it is attributed to the current TAR which has improvements in surgical technique, uncemented implant fixation and minimally constrained articulation. In the clinical result, they can show promised surgical result when compared to earlier attempts in TAR. However, TAR is still not as successful as total knee replacement (TKR) or total hip replacement (THR), it needs to be note that there are limitations in concerning of long term performance of TAR, the high failure rate still associated with wear of the PE (polyethylene) component that has related with their material property and surface roughness. The aim of this study was to introduce the tribology characteristics of total ankle joint prosthesis with one of TDR model which was fabricated to try multi-axis wear test as a region of motion in ankle joint. The wear specimen of TDR was prepared with Ti-6Al-4V alloy and UHMWPE (ultra-high molecular weight polyethylene) for tibia-talus and bearing component, respectively. A wear test was carried out using a Force 5 (AMTI, Massachusetts, US) wear simulator which can be allowed to move in three axis to flexion-extension ($+3^{\circ}{\sim}-6^{\circ}$), internal-external axial rotation (${\pm}5^{\circ}$), as well as sinusoidal compressive load (1.6 kN, R=10). All tests were performed following standard ISO 14243, wear rate was calculated with weight loss of UHMWPE bearing while the specimen has tested at certain cycles. As based on the preliminary results, wear rate of UHMWPE bearing was $7.9{\times}10^{-6}mg/cycles$ ($R^2=0.86$), calculated loss weight until $10^7cycles$ was 79 mg, respectively.

• 분석과학
• /
• 제13권6호
• /
• pp.766-774
• /
• 2000

유도결합 플라스마 원자방출분광법(ICP-AES)을 이용하여 몽골산 크롬철광의 성분을 분석하였다. 크롬철광을 용해시키기 위하여 과염소산-인산의 흔합산과 융제로서 $Na_2O_2$의 적용성을 검토한 결과 최적의 용해방법은 용융법이었다. 크롬광의 주성분과 미량성분을 ICP-AES로 정량할 때 과량의 Na가 측정파장에 미치는 영향을 조사하였다. Al, Cr, Fe 및 Mg과 같은 주성분원소의 경우 Na가 250 mg/L까지 영향을 받지 않았으나, Co, Ni, Ti, V 및 Zn과 같은 미량성분들은 Na가 1,250 mg/L인 경우 측정원소와 파장에 따라 방출선의 세기는 1-5% 정도 감소하였다. 본 방법의 정확도를 확인하기 위하여 중성자방사화분석으로 얻은 결과와 상대편차를 비교하였다. $Al_2O_3$, $Cr_2O_3$, FeO 및 MgO의 경우에는 FeO를 제외하고 상대편차가 5% 이내이며, Co, Mn, V 및 Zn의 경우에는 ~20-8% 범위였다.