• Magazine of the Korean Society of Agricultural Engineers
• /
• v.16 no.4
• /
• pp.3572-3584
• /
• 1974

본 논문은 Thrower의 양곡성능에 관한 예측 방정식을 차원해석법을 적용하여 유도하는데 있다. Thrower의 능률에 큰 영향을 미친다고 생각되는 인자들간의 관계식들을 Buckingham의 $\pi$이론에 의하여 구하여 졌으며 본연구에 사용한 Thrower는 현재 농촌에서 사용되고 있는 자동탈곡기의 Thrower와 유사한 형으로 제작된 것이며 실험에 사용된 시료는 벼의 경우는 통일벼와 미네히까리 품종이고 보리 품종으로서는 나맥이며, Thrower의 Impeller 직경, 속도 및 투입량을 변화시켜 가면서 각 시료에 대하여 양곡높이를 측정하여 그 예측방정식을 유도하였다. 본 논문에서 얻은 결과는 다음과 같다. 1. Thrower의 양곡성능에 지대한 영향을 미친다고 생각되는 주요 인자들을 Thrower의 양정, impeller의 직경과 속도, 투입량, 곡립의 밀도, 중력가속도등이라 간주하여 Buckingham의 $\pi$이론을 적용하여 이들에 관한 $\pi$항들을 결정하였으며 그 결과는 다음과 같다. {{{{ pi 1= { D} over {H } , pi 2= { { DN}^{ { 1} over {2 } } } over { { g}^{ { 1} over { 2} } }, pi 3= { Q} over { { g}^{ { 1} over {2 } } { rho D}^{ { 2} over {6 } } }}}}} 2. 실험에 의하여 구해진 $\pi$항문의 관계식을 합성하여 Thrower의 양곡성능에 관한 시료별 예측방정식을 구하였으며 이 식들은 아래와 같다. 통일 : $\pi$1=0.1223($\pi$2)-1.1813$\times$($\pi$3)-0.1864 미네히까리 : $\pi$1=0.1185($\pi$2)-0.9663$\times$($\pi$3)-0.1575 나맥 : $\pi$1=0.1599($\pi$2)-1.2350$\times$($\pi$3)-0.1382 3. 현재 농촌에서 사용되고 있는 자동탈곡기체 부착된 Thrower의 회전수, Impeller의 직경 및 투입량은 각각 1,100rpm, 30cm 및 150gr/sec 정도로서 이와같은 수준의 변량들을 기초로 하여 본 논문에서 유도한 예측방정식을 적용하여 Thrower의 양정을 산출한 결과, 통일벼의 경우는 2.6m정도였고 미네히까리 품종과 나맥의 양정은 각각 2.4m, 2.9m 정도였다. 이와같은 사실로부터 1m내외의 양정만으로 되어있는 자동탈곡기 Thrower의 경우 제작비절감, 소요동력 감소를 기하고 아울러 과립의 손상을 줄이기 위해서는 설계 또는 작동조건의 변경을 통해 Thrower의 회전수를 현재 수준이하로 줄일 필요가 있다고 판단되었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.5148-5154
• /
• 2012

The purpose of this study was to analyze the kinematic characteristics of the thrower's center of mass (COM) and the shot that her performance hits record high for the 29th National Athletic Competition. Two S-VHS video cameras were used to visualize. The Direct Linear Transformation technique was employed to paint a clear picture in the three dimensional coordination. Kwon3D was used to analyze the data. The results showed that release velocity and height were 13.73 m/s and 198.6 cm(119% by height ratio), respectively, which is considered as peak performance comparing an extensive review of previous literature on the shot put. Release angle was $34^{\circ}$, which is lower than the previous studies. The path of thrower's center of mass is needed to travel in a release direction during the flight phase. The vertical movement of the thrower's center of mass during the driving should be controlled. At release, the perfact timing is required without vertical and horizontal movements of the thrower's center of mass.

• Korean Journal of Applied Biomechanics
• /
• v.21 no.5
• /
• pp.661-667
• /
• 2011

The purpose of the study was to compare selected kinematic variables between the female medalists and a Korean female javelin thrower at the IAAF World Championships, Daegu 2011. Three medalists and one Korean javelin thrower that participated in the Championships were videotaped using three high-speed cameras (300 frames/s, EX-F1 Exilim, Casio, Japan). This study identified the performance differences between the two groups. The results showed that the Korean female javelin thrower (KFJT) clearly had a greater delivery phase time than the female medalists. In order to throw farther, a thrower must exert a greater force to accelerate their body in a short time. This study also found that the release velocity of the KFJT was lower than that of the female medalists. The KFJT showed evidence of using her extremities differently to achieve the maximum release velocity. When comparing the inclination angle of the trunk across javelin throwers, the lowest value was recorded in the KFJT. Because the trunk position at release plays a significant role in determining the release height and release velocity, the KFJT should not rely on her upper extremities to achieve as high a release velocity as possible.

• Korean Journal of Applied Biomechanics
• /
• v.21 no.5
• /
• pp.653-660
• /
• 2011

The purpose of this study was to compare selected kinematic variables between male medalists and a Korean male javelin thrower at the IAAF World Championships, Daegu 2011. The three medalists and one Korean javelin thrower that participated in the Championships were videotaped using three high-speed cameras (300 frames/s, EX-F1 Exilim, Casio, Japan). The results showed that the release and attitude angles of the Korean male javelin thrower (KMJT) were greater than that of the medalists, whereas the attack angle of the KMJT was smaller than that of the medalists. This study also found that the KMJT clearly had a lower release height than the medalists. As a possible adaptation of his physique to the skill, the KMJT used a small trunk inclination angle and produced greater inclination angles at his upper extremities. These results may be linked to an increase in the release angle of the KMJT. There were some difference between the KMJT and the medalists in terms of the length and duration of the delivery phase. In harmony with the shorter length of the delivery phase, its duration was shorter for the KMJT in comparison to the medalists. Because the delivery stride is considered to be a primary generator of endpoint speed, this decrease in the delivery phase time would decrease the javelin velocity at release. The amount of time taken in the delivery phase may be a critical factor to enhance a javelin thrower's performance. Thus, rhythmic movement training specifically designed for the KMJT will help him attain an optimal throwing position.

• Journal of Korean Orthopaedic Sports Medicine
• /
• v.6 no.2
• /
• pp.77-82
• /
• 2007

The thrower's shoulders require a delicate balance between mobility and functional stability. First step to successful nonoperative management is an accurate diagnostic approach. Rehabilitation program follows a well-organized, multiphase approach with focus on controlling painful inflammation, restoring muscle balance, obtaining joint flexibility, improving proprioception and neuromuscular control, and effectively returning to competitive pitching. In this article, the typical musculoskeletal profile of the overhead thrower and various rehabilitation programs for specific injuries are discussed.

• The Academic Congress of Korean Shoulder and Elbow Society
• /
• 2006.03a
• /
• pp.75-75
• /
• 2006

• Journal of the Korean institute of surface engineering
• /
• v.21 no.1
• /
• pp.19-27
• /
• 1988

The principe and practice of pulse plating, and prospect in the future on pulse plating are reviewed. Some of the advantages of pulse pulse plating are detailed as compared with DC plating. The advantages of pulse plating are summarized as follows: 1)smooth and fine grained deposits 2) reduction in hydrogen embrittlement of deposits 3) reduction of residual stress and microcracks in the deposit 4) improvement of physical properties 5) uniform alloy composition through the deposit thinkness 6) improved thrower and adhesion.

• Journal of Biosystems Engineering
• /
• v.16 no.2
• /
• pp.133-141
• /
• 1991

This study was undertaken to investigate the structural and configurational characteristics of the tailings return-unit in the commercially available head-feed combines and to study the aero-dynamical behavior of the tailings in the units. The mathematical model of the motion of tailings in the thrower casing was developed and the simulated trajectories for different type of units was analyzed to compare with the measured ones. The air-stream velocity profile in various locations along the tailings returning duct was measured to find the effect of configurational characteristics and blade tip speed. The results of the study are summerized as follows. 1. The ejecting angle, which is the angle between the direction of the particle velocity ejecting from the blade and the horizontal axis, was found to be about $66^{\circ}$ in both the simulation and experiment. The angle was much greater than the setting angle of actual duct of the combines studied, which were $48{\sim}56^{\circ}$. By comparison of these results, it was suggested to change duct setting angle so as to reduce the frictional force, between the duct wall and tailings, by reducing the difference between the ejecting and setting angles. 2. The velocity of the air stream in the duct was in general higher in the upper bound of the duct compared to the lower and decreased as the stream went toward the end of duct. The comparison of the tailings units among the combines studied showed a superior performance with the tapered duct having small diameter in the outlet and with greater number of thrower blade.

• Journal of Biosystems Engineering
• /
• v.16 no.2
• /
• pp.124-132
• /
• 1991

This study was carried out to obtain the information needed in the development of forward speed control system and the improvement of combine performance. The effects of variety, grain moisture content and forward speed on the combine load characteristics were investigated through experiments. The results of this study are summarized as follows. 1. A data acquisition system was developed to measure the engine speed and the torques and speeds of the threshing cylinder, dean-grain auger and tailings-return auger. The system consisted of transducers, signal conditioner, interface board and microcomputer. The system accuracy is better than ${\pm}2.3%$ full scale. 2. Linear regression equations were obtained for the torque, speed and power requirement of threshing cylinder for different paddy varieties, grain moisture contents and feed rates. 3. The maximum value of relative frequency for threshing cylinder torque decreased as the increase in feed rate and moisture content. The range of torque fluctuation was 1.2~3.7 and 1.2~1.9 times the average and maximum torque, respectively. The maximum value of power spectrum density (PSD) appeared to be about 11 Hz regardless of paddy variety, grain moisture content and feed rate. 4. The speed of tailings return thrower decreased rapidly at below 900rpm, and it fell to near zero about 3 seconds after that time. When the travelling of combine harvester was stopped immediately after sensing the overload, it took about 7 seconds for a full recovery of the no-load speed of tailings return thrower.

• Korean Journal of Applied Biomechanics
• /
• v.19 no.1
• /
• pp.67-75
• /
• 2009

The purpose of this study is to analyze the effects of target position on the bowling motion. Four female high school athletes with more than four years of bowling experiences were recruited to this study. The major results of this study are as follows; When a subject treats the 1st pin, The spin angle of a coxa for the target position is largely kept from the downswing to the backswing peak point. When a subject treats the 7th pin, As the 7th pin exists at the left side for the right shoulder axis of the thrower, the movement of the ball center of the thrower from side to side is the lowest. In addition, the time required and horizontal speed appear the highest in the release section. The slant angle of a shoulder is largely increased as she moves from the backswing peak point to the release section. The twist angle of a shoulder also appears small as a throw motion is made toward the left side. When a subject treats the 10th pin, The spin angle of a shoulder and the twist angle of a body in motion appear the largest in the release section. So, there are the effects of target position on the bowling motion.