• Journal of Fashion Business
• /
• v.2 no.4
• /
• pp.93-101
• /
• 1998

Knit products which had been limited only to underwear, recently became popularized, fashionized and highly classified covering even outer garments such as sportswear like golfwear, woman's dress, and man' s suit. As fashion cycle is getting shorter and the more a nation advanced prefers knit to woven fabrics knit industry has a very bright prospect, particularly woman's knit which is sensitive to fashion can be said as a fashion product with high value added. This study is to grasp the physical properties of stitch which are fundamental to the development of knit products. For this purpose, 2/20s of 100% wool were woven by the author of this study to basic plain stitch, rib stitch, varied transfer stitch, and float stitch on a SEMASEIKI cross knitter 7G to test the physical properties, and the result was as follows; 1. As for the relation between knit stitch and rate of extension recovery, rate of extension recovery was higher in the course direction than in the wale direction of three stitches except transfer stitch; rib stitch showed the highest rate of extension recovery in the course direction while float stitch showed the highest rate of extension recovery in the wale direction. 2. As for the relation between knit stitch and bursting strength elastic rib stitch showed higher bursting strength to indicate elasticity is an important factor of bursting strength and float stitch showed higher bursting strength too to indicate that the floating yarn on the surface plays a role of support. 3. As for the relation between knit stitch and air permeability perforated transfer stitch showed the lowest air permeability to prove that the size of perforation affects on the air permeability a great deal. 4. As for the relation between knit stitch and warmth retaining rib stitch through two lined needle bar showed the highest degree. The reason the warmth of perforated transfer stitch didn't decrease much was because the perforation wasn't big enough and content of air increased from the unevenness of the perforated parts through stitch variation. Based upon this result, each stitch can be characteristically summarized as follows; plain stitch showed a stable condition of knit cloth in four kinds of physical property test. And rib stitch is proper to tighten the edge of sleeve or clothe making use of its excellent extension recovery and to make socks for the highest bursting strength and warmth retaining. In the case of transfer stitch, seasonable designs can be taken by controlling the size of loop. Considering the pleasantness, underwear should be made of stitches with good air permeability float stitch was revealed to have color and pattern effects and a great bursting strength. This study has limitations in the aspect that it dealed with a small part of various knit stitches and the items of physical property test were not enough. The author of this study hopes that further studies would make deeper understandings about knit stitch based on more varied stitches and physical property tests ultimately to contribute to the development of fashionable designs proper to maximize the usage, function and originality.

• Journal of Animal Science and Technology
• /
• v.46 no.6
• /
• pp.937-946
• /
• 2004

Duroc is widely used to improve the meat quality and productivity. To elucidate the phylogenetic relation and the sequence specificity for the maternal property, the complete sequence of mitochondrial genome was determined and the population diversity of Duroc was investigated in this study. The length of mtDNA tested is 16,584-bp. There are several insertion/deletion mutations in the control region and coding regions for tRNA and rRNA, respectively, but not in peptide-coding regions. Four peptide-coding genes(COⅡ, COⅢ, ND3 and ND4) showed incomplete termination codon sequences such as T--, and two(ND2 and ND4L) did alternative initiation codons(AIC), respectively. Especially, the initiation codon sequences of ND2 gene were polymorphic in this population. Polymorphisms were detected in 11-bp duplication motif within control region as well as ND2 and CYTB. Variation patterns observed from the tests on three mtDNA regions were linked completely and then two haplotypes obtained from combining the data dividing this population. Duroc mtDNA is observed at the European pig cluster in the phylogenetic tree, however, the results from the population analyses supported previous opinions. This study suggests that the breed Duroc was mainly originated from the European pig lineage, and Asian lineage was also used to form the pig breed Duroc as maternal progenitors.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.1
• /
• pp.1-8
• /
• 2017

Three small scale hollow circular reinforced concrete columns with aspect ratio 4.5 were tested under cyclic lateral load with constant axial load. Diameter of section is 400 mm, hollow diameter is 200 mm. The selected test variable is transverse steel ratio. Volumetric ratios of spirals of all the columns are 0.302~0.604% in the plastic hinge region. It corresponds to 45.9~91.8% of the minimum requirement of confining steel by Korean Bridge Design Specifications, which represent existing columns not designed by the current seismic design specifications or designed by seismic concept. The longitudinal steel ratio is 2.017%. The axial load ratio is 7%. This paper describes mainly crack behavior, load-displacement hysteresis loop, seismic performance such as equivalent damping ratio, residual displacement and effective stiffness and flexural over-strength of circular reinforced concrete bridge columns with respect to test variable. The regulation of flexural over-strength is adopted by Korea Bridge Design Specifications (Limited state design, 2012). The test results are compared with nominal strength, result of nonlinear moment-curvature analysis and the design specifications such as AASHTO LRFD and Korea Bridge Design Specifications(Limited state design).

• Proceedings of the Korea Crystallographic Association Conference
• /
• 2003.05a
• /
• pp.18-18
• /
• 2003

Thioredoxin (Trx) is a small redox protein that is ubiquitously distributed from achaes to human. In diverse organisms, the protein is involved in various physiological roles by acting as electron donor and regulators of transcription and apoptosis as well as antioxidants. Sequences of Trx within various species are 27～69% identical to that of E. coli and all Trx proteins have the same overall fold, which consists of central five β strands surrounded by four α helices. The N-terminal cysteine in WCGPC motif of Trx is redox sensitive and the motif is highly conserved. Compared with general cysteine, the N-terminal cysteine has low pKa value. The result leads to increased reduction activity of protein. Recently, novel thio.edoxin-related protein (TRP14) was found from rat brain. TRP14 acts as disulfide reductase like Trx1, and its redox potential and pKa are similar to those of Trx1. However, TRP14 takes up electrons from cytosolic thioredoxin reductase (TrxR1), not from the mitochondrial thioredoxin reductase (TrxR2). Biological roles of TES14 were reported to be involved in regulating TNF-α induced signaling pathways in different manner with Trx1. In depletion experiments, depletion of TRP14 increased TNF-α induced phosphorylation and degradation of IκBα more than the depletion Trx1 did. It also facilitated activation of JNK and p38 MAP kinase induced by TNF-α. Unlike Trx1, TRP14 shows neither interaction nor interference with ASK1. Here, we determined three-dimensional crystal structure of TRP14 by MAD method at 1.8Å. The structure reveals that the conserved cis-Pro (Pro90) and active site-W-C-X-X-C motif, which may be involved in substrate recognition similar to Trx1 , are located at the beginning position of strand β4 and helix α2, respectively. The TRP14 structure also shows that surface of TRP14 in the vicinity of the active site, which is surrounded by an extended flexible loop and an additional short a helix, is different from that of Trx1. In addition, the structure exhibits that TRP14 interact with a distinct target proteins compared with Trx1 and the binding may depend mainly on hydrophobic and charge interactions. Consequently, the structure supports biological data that the TRP14 is involved in regulating TNF-α induced signaling pathways in different manner with Trx1.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.4 s.316
• /
• pp.55-60
• /
• 2007

In high field (> 3 T) MR imaging, the magnetic field inhomogeneity in the target object increases due to the nonuniform electro-magnetic characteristics of the relatively high RF frequency. Especially in the body imaging, the effect causes more serious problems resulting in locally high SAR(Specific Absorption Ratio). In this paper, we propose an optimized parallel-transmission RF coil and show the utility of the coil by FDTD simulations to overcome the unwanted effects. Three types of TX coil elements are tested to maximize the efficiency and their driving patterns(amplitude and phase) optimized to have adequate field homogeneity, proper SAR level, and sufficient field strength. For the proposed coil element of $25cm{\times}8cm$ loop structure with 12 channels for a 3.0 T body coil, the field non-uniformity of more than 70% without optimization was reduced to about 26 % after the optimization of driving patterns. The experimental as well as simulation results show that the proposed parallel driving scheme is clinically useful for (ultra) high field MRI.

• Analytical Science and Technology
• /
• v.17 no.2
• /
• pp.145-152
• /
• 2004

In this study, analytical characteristics of S gas detection technique were investigated against four major reduced S compounds (including hydrogen sulfide; methyl mercaptan; dimethyl sulfide (DMS); and dimethyl disulfide (DMDS)). To analyze such properties, an analytical system was constructed by combining the GC/PFPD system with the loop injection method. The results of our analysis indicated that response behavior of S gases differs greatly between compounds; H2S exhibited the weakest sensitivity of all compounds, while DMDS with two S-atom compounds the strongest sensitivity. To learn more about their response behavior on GC/PFPD method, their calibration patterns were compared using the three arbitrarily set concentration ranges of low, intermediate, and high. The results showed that calibration patterns of each compound are distinguished because of different factors. There was a line of evidence that calibration of $H_2S$ was affected noticeably by adsorptive loss within the system, whereas those of DMS and DMDS were influenced most sensitively by such factor as the linearity response at a given PMT voltage setting. The overall results of our study suggest that quantification of malordorous S compounds require a better knowledge of compound-specific response behavior against GC detection.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.637-644
• /
• 2016

This paper is a follow-up to previous papers entitled, "Development of Tunnel-Environment Monitoring System and Its Installation" I [1] and II [2]. The target tunnel of these studies is the Solan Tunnel, which is a loop-type, single-track, 16.7-km-long tunnel located in mountainous terrain and passing through the Baekdudaegan mountain range. It is an ordinary railway tunnel designed for both freight and passenger trains. We analyzed the environmental conditions of the tunnel using temperature and humidity data recorded over approximately one year. The data were recorded using the Tunnel Rough Environment Measuring System (TREMS), which measures environmental data in subway and high-speed train tunnels and is installed in three locations inside the tunnel. Previous studies analyzed environmental conditions inside tunnels located in or near a city, whereas the tunnel in this study is located in a mountainous area. The tunnel conditions were compared with those measured outside the tunnel for each month. Hourly changes during summer and winter periods were also analyzed, and the environmental conditions at different locations inside the tunnel were compared. The results are widely applicable in studies on the thermal environment and air quality of tunnels, as well as for computer analysis of tunnel airflow such as tunnel ventilation and fire simulations.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.5
• /
• pp.1032-1043
• /
• 1989

The heat transfer characteristics of the drag reducing polymer solutions are investigated experimentally in the thermal entrance region of circular tube flows. Fluids used in experiments are the aqueous solutions of high molecular polymer, polyacrylamide Separan AP-273 and the range of polymer concentrations is from 20 to 1000 wppm. Two stainless steel tubes with inside diameter 8.5mm(L/D=712) and 10.3mm(L/D=1160) are used for the heat transfer flow loops. The flow loop is set up to measure friction factors and heat transfer coefficients of test sections in two different modes; the recirculating flow system and once-through flow system. The test tubes are heated directly by electricity to apply the constant heat flux boundary conditions to the wall. Three different types of adaptors are used to observe the effects of the upstream flow conditions of the heat transfer test sections. The viscosity and characteristic relaxation time of the test fluids circulating in the flow system are measured by the capillary tube viscometer and falling ball viscometer at regular time intervals. The installed adaptors exhibit slight effect on the entrance heat transfer of Newtonian fluid. However, no noticeable effects are observed for the entrance heat transfer of the drag reducing fluids. The order of magnitude of the thermal entrance lengths of the drag reducing fluids which follow the minimum friction asymptote is much longer than that of Newtonian fluids in turbulent flows. A new dimensionless parameter, the viscoelastic Graetz number, is defined and all the experimental data are recasted in terms of the viscoelastic Graetz number. The local Nusselt number of the viscoelastic fluids is represented as a function of flow behavior index n and the viscoelastic Graetz number. As degradation continues the viscosity and the characteristic relaxation time of the testing fluids decrease. Weissenberg number defined by the relaxation time and D/V appears to be a proper dimensionless parameter in describing degradation effects on heat transfer of the viscoelastic fluids.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.6
• /
• pp.739-745
• /
• 2017

Many studies have been conducted to reduce environmental pollution by ships and reduce fuel consumption. As part of this effort, research on power conversion systems through DC distribution systems that link renewable energy with conventional power grids has been pursued as well. The diode rectifiers currently used include many lower harmonics in the input current of the load and distort supply voltage to lower the power quality of the whole system. This distortion of voltage waveforms causes the malfunctions of generators, load devices and inverter pole switching elements, resulting in a large number of switching losses. In this paper, a controller is presented to improve DC output waveforms, the input Power Factor and the THD of an AFE type PWM rectifier used for PLL. DC output voltage waveforms have been improved, and the input Power Factor can now be matched to the unit power factor. In addition, the THD of the input power supply has been proven by simulation to comply with the requirements of IEEE Std514-2014.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.40 no.4
• /
• pp.261-273
• /
• 2022

This study aims to predict the land use demand of Seongnam-city using system dynamics and to simulate the effect of changes in family structure and land use density adjustment policy on land use demand. This study attempted to construct causal loop diagrams and an analysis model. The changes in land use demand over time were predicted through simulation results. As a result of the analysis, as of 2035, an additional supply of 2.08 km² for residential land and 1.36 km² for commercial land is required. Additionally, the current supply area of industrial land can meet the demand. Three policy experiments were conducted by changing the variable values in the basic model. In the first policy experiment, it was found that when the number of household members decreased sharply compared to the basic model, up to 7.99 km² of additional residential land were required. In the second policy experiment, if the apartment floor area ratio was raised from 200% to 300%, it was possible to meet the demand for residential land with the current supply area of Seongnam-city. In the third policy experiment, it was found that even if the average number of floors in the commercial area was raised from four to five and the building-to-land ratio in the commercial area was raised from 80% to 85%, the demand for commercial land exceeded the supply area of the commercial area in Seongnam-city. This study is meaningful in that it proposes a new analytical model for land use demand prediction using system dynamics, and empirically analyzes the model by applying the actual urban planning status and statistics of Seongnam-city.