• Journal of the Korean Applied Science and Technology
• /
• v.24 no.1
• /
• pp.31-46
• /
• 2007

This study was focused on the maximization of flame-retardancy of polyesters by a synergism of simultaneously introduced chlorine and phosphorus into polymer chains of modified polyesters. To prepare modified polyesters, reaction intermediates, TD-adduct (prepared from trimethylolpropane/2,4-dichlorobenzoic acid (2,4-DCBA)) and TMBO (prepared from tetramethylene bis(orthophosphate)), were prepared first, then condensation polymerization of the prepared intermediates, adipic acid, and 1,4-butanediol were carried out. In the condensation polymerization, the content of phosphorus was fixed to be 2%, and the content of 2,4-DCBA that provides chlorine component was varied to be 10, 20, and 30wt%, and we designated the prepared modified polyesters containing chlorine and phosphorus as ABTT-10C, -20C, -30C. Two-component PU flame-retardant coatings (ABTTC, ABTTC-10C, ABTTC-20C, ABTTC-30C) were prepared by the curing of synthesized ABTTs with a curing agent of allophanate/trimer at room temperature. To examine the film properties of the prepared PU flame-retardant coatings, film specimens were prepared with the prepared coatings. The film properties of ABTTC, ABTTC-10C and ABTTC-20C, which contain 0, 10 and 20wt% 2,4-DCBA, respectively, were proved to be good, whereas the film properties of ABTTC-30C, which contains 30wt% 2,4-DCBA, was proved to be a little bit poor. Two kinds of flame retardancy tests, $^{\circ}45Meckel$ burner method and LOI method were performed. With the $^{\circ}45Meckel$ burner method, three flame-retardant coatings except ABTTC showed less than 3.4cm of char length, and showed less than 2 seconds of afterflaming and afterglow. From this result, the prepared flame-retardant coatings were proved to have the 1st grade flame retardancy. With the LOI method, the LOI values of the coatings containing more than 10wt% 2,4-DCBA were higher than 30%, which means that the coatings possess good flame retardancy. From these results, it was found that synergistic effect in flame retardancy was taken place by the introduced phosphorus and chlorine.

• Applied Chemistry for Engineering
• /
• v.33 no.2
• /
• pp.151-158
• /
• 2022

In this paper, parameter characteristics such as pH effect, isotherm, kinetic and thermodynamic parameters and competitive adsorption of dyes including malachite green (MG), direct red 81 (DR 81) and thioflavin S (TS), which have different functional groups, being adsorbed onto activated carbon were investigated. Langmuir, Freundlich and Temkin isotherm models were employed to find the adsorption mechanism. Effectiveness of adsorption treatment of three dyes by activated carbon were confirmed by the Langmuir dimensionless separation factor. The mechanism was found to be a physical adsorption which can be verified through the adsorption heat calculated by Temkin equation. The adsorption kinetics followed the pseudo second order and the rate limiting step was intra-particle diffusion. The positive enthalpy and entropy changes showed an endothermic reaction and increased disorder via adsorption at the S-L interface, respectively. For each dye molecule, negative Gibbs free energy increased with the temperature, which means that the process is spontaneous. In the binary component system, it was found that the same functional groups of the dye could interfere with the mutual adsorption, and different functional groups did not significantly affect the adsorption. In the ternary component system, the adsorption for MG lowered a bit, likely to be disturbed by the other dyes meanwhile DR 81 and TS were to be positively affected by the presence of MG, thus resulting in much higher adsorption.

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.140-145
• /
• 2005

The desulfurization abilities using GC/microreactor have been examined for $CuO-Fe_2O_3$ sorbents with respect to calcination temperatures of 700, 900 and $1,100^{\circ}C$. CuO was used as a main active component, $Fe_2O_3$ was used as an additive one and 25 wt% $SiO_2$ was used as a support. The desulfurization reaction temperature was $500^{\circ}C$ and the regeneration reaction temperature was $700^{\circ}C$. From the XRD results, the $CuFeO_2$ compound has been observed for the fresh sorbent calcined at $1,100^{\circ}C$ and the $CuFeS_2$ compound for the reacted sorbent calcined at $1,100^{\circ}C$. By the BET results, however any significant differences among sorbents calcined at the three different temperatures of 700, 900 and $1,100^{\circ}C$ haven't been observed. Especially CFS1 (CuO : $Fe_2O_3$ : $SiO_2$=67.5 wt% : 7.5 wt% : 25 wt%) sorbent calcined at $1,100^{\circ}C$ maintained about 10 g sulfur/100 g sorbent for 100 cycles by the cyclic test.

• Applied Chemistry for Engineering
• /
• v.5 no.6
• /
• pp.949-956
• /
• 1994

The objective of this study is to experimentally investigate the ion exchange characteristics of five types of Zeolite(Zeolite-A, 13X, Y, Mordenite, Chabazite) for effective removal of Cs, Sr and Co ions in water solution at low concentration(0.01 N and 0.005 N). Total ion exchange capacity and equilibrium isotherm are measured, and free-energy change(${\Delta}G^0$) and enthalpy change(${\Delta}H^0$) in ion exchange reaction are calculated from experimental results. In addition the ion exchange equilibrium in the three-component system for three types of zeolite showing better efficiency is measured and plotted in triangle coordinates. It is shown from experimental results that the magnitude of free-energy change increases with the increasing ion selectivity, and the difference of free energy change between ions correlates closely with that of ion selectivity. The results also shows that Chabazite is effective for the adsorption of Cs ion, and Zeolite-A and Zeolite-13X for that of Sr and Co ions.

• Journal of Adhesion and Interface
• /
• v.20 no.1
• /
• pp.9-14
• /
• 2019

The change of three different reagents for electrical conductive paint using aircraft coating with elapsing time of exposure to different condition was investigated. Three different reagents were poured into the vial bottles, stored in air condition and room temperature and observed with elapsing days. In addition, adhesion property of paint was tried using cross cut tape test after storage of $N_2$ atmosphere. The weight of each different reagent was measured along with elapsing time. To confirm the change of chemical component with exposure of air atmosphere, FT-IR was performed. The weight of part A and Part B decreased slightly whereas the weight of part C decreased rapidly and the precipitation was remained. The part B was cured after exposure of $N_2$ atmosphere and the 2250 cm-1 from FT-IR peak decreased slowly at the same time. It was considered that the water contained in air accelerated the reaction of -NCO functional groups and it caused the curing whereas $N_2$ atmosphere not contained water and it resulted in the retardancy of curing.

• Applied Biological Chemistry
• /
• v.7
• /
• pp.15-19
• /
• 1966

In order to investigate the stability of the major component of malathion E.C. product, dimethyl S-(1, 2-dicarboxyethoxyethyl) dithiophosphate, toward the quality of glasswares as container, the amount of extractable inorganic components, change of pH and decomposition of the major component of the product were examined during the storage in brown-colored bottles of 100 ml. volume from 3 different companies in comparison with that in a Pyrex flask. 1. Malathion E.C. product was put in three containers A,B and C, and any changes occurring in storage were analyzed at three intervals of 60, 120 and 240 days. 2. It was shown that the amounts of Si, Mg, K, Ca, and Na extracted during these periods of storage differed markedly depending on the qualify of container. Container A revealed ten times higher extraction of Na and Ca than container B and C in a 8-month period. 3. Three commercial containers revealed the shift of pH from 6.5 to alkaline reaction in the storage whereas the Pyrex flask did not show any detectable change. In particular, the pH in container A changed to 9.2 in 60 days and 9.9 in 240 days. 4. The decomposition of malathion was the greatest in container A which showed the decomposition of 7.37% in 240 days. On the other hand, 0.5% was decomposed in the Pyrex flask. 5. The decemposition of malathion had a high correlation with the change of pH of water· in the same container, $r^2$ being 0.899. From the above results, it is concluded that about 10% of malathion E.C. product is decomposed in a year due to the alkaline metallic salts extracted from the container when it is stored in glassware bottles of lower quality.

• Atmosphere
• /
• v.26 no.3
• /
• pp.357-372
• /
• 2016

Northeast Asian regions have recently become the main source of anthropogenic and natural aerosols. Measurement of aerosols on the sea in these regions have been rarely conducted since the experimental campaigns such as ACE-ASIA (Asian Pacific Regional Aerosol Characterization Experiment) in 2001. Research vessel observations of aerosol mass and chemical composition were performed on the Yellow and south sea around the Korean peninsula. The ship measurements showed six representative cases such as aerosol event and non-event cases during the study periods. On non-event cases, the anthropogenic chemical and natural soil composition on the Yellow sea were greater than those on the south sea. On aerosol event cases such as haze, haze with dust, and dust, the measured mass concentrations of anthropogenic chemical and element compositions were clearly changed by the events. In particular, methanesulfonate ($MSA^-$, $CH_3SO_3^-$), a main component of natural oceanic aerosol important for sulfur circulation on Earth, was first observed by the vessel in Korea, and its concentration on the Yellow sea was three times that on the south sea during the study period. Sea salt concentration important to chemical composition on the sea is related to wind speed. Coefficients of determination ($R^2$) between wind speed and sea salt concentration were 0.68 in $PM_{10}$ and 0.82 in $PM_{2.5}$. Maximum wave height was not found to be correlated to the sea salt concentration. When sea-salt comes into contact with pollutants, the total sea-salt mass is reduced, i.e., a loss of $Cl^-$ concentration from NaCl, the main chemical composing sea salt, is estimated by reaction with $HNO_3$(gas) and $H_2SO_4$(gas). The $Cl^-$ concentration loss by $SO_4^{2-}$ and $NO_3^-$ more easily increased for $PM_{10}$ compared to $PM_{2.5}$. The results of this study will be applied to verifying a dust-haze forecasting model. In addition, continued vessel measurements of aerosol data will become important to research for climate change studies in the future.

• Korean Chemical Engineering Research
• /
• v.54 no.4
• /
• pp.443-447
• /
• 2016

The microalgae have cellulose as a main structural component of their cell wall and the lignin content in microalgae is much lower than other lignocellulosic biomass. Therefore, fermentable sugar production from microalgae (Tetraselmis KCTC 12236BP) can be carried out under pretreatment without high temperature and high pressure. It was investigated that the effect of hot-water pretreatment using sulfuric acid for lipid extracted algae which is expected to be a next generation biomass. The effects of three major variables including extraction temperature, acid concentration and time on the enzymatic hydrolysis were investigated. Among the tested variables, temperature and acid concentration showed significant effects and optimum pretreatment conditions for the economic operation criteria were obtained as follows: reaction temperature of $120^{\circ}C$, sulfuric acid concentration of 2 mol and pretreatment time of 40 min. Under the optimum conditions of acidic hot water pretreatment, experimentally obtained hydrolysis yield were 95.9% which showed about 2.1 fold higher compared with enzymatic hydrolysis process. Therefore, acid pretreatment under mild condition was proven to be an effective method for fermentable sugar production from lipid extracted microalgae.

• Journal of Chest Surgery
• /
• v.30 no.8
• /
• pp.739-746
• /
• 1997

A variety of experiments concerning the development of ideal prosthetic grafts for correcting circumferential tracheal defects have been performed. The requirements for an ideal tracheal prosthesis are impermeability to air, consistency to prevent collapse, and acceptance by the host tissue causing a minimum inflammatory reaction, allowing fibroblastic infiltration and epithelialization. The synthetic material, polyurethane(PU), is known as a biocompatible polymer with an inert component. In this study, the tracheal prosthesis was made from microporous PU(30 micrometer in diameter) coated with gelatin and reinforced with isoplastic rings. This procedure provides the prosthesis with a compression strength. The out side diame er of the prosthesis was 20 mm with a length of 30 mm. The gelatin used in the study was obtained from pig skin and immobilized and cross-linked by irradiation(60 Co gamma ray) to promote host tissue incorporation and render the prosthesis epithelization after implantation. Animal experiments using 10 mongrel dogs were performed to compare three kinds of prosthesis; gelatin coated polyurethane graft, uncoated polyurethane graft, and prosthesisf pericadium complex graft. After 6 weeks of implantation, the epithelialization of implants was seen on the gelatin-coated and prosthesisfpericadium complex grafts. Implanted prosthesis were complicated by airway obstruction due to anastomosis granuloma. Early tracheal stenosis was found in the uncoated graft group. Two kind of anastomosis techniques were tested on the gelatin-coated prosthesis. Everted anastomosis resulted severe granuloma than the inverted anastomosis. In the prosthesislpericadium complex graft, bacteria and inflammation at a anastomotic site was found. Based on these results, gelatin coated porous polyurethane trachea prosthesis is biocompatible and may be useful in clinical application with further investigation.

• Journal of Environmental Analysis, Health and Toxicology
• /
• v.21 no.4
• /
• pp.220-228
• /
• 2018

$PM_{2.5}$-bound mercury (PBM) was monitored at weekly intervals for three years (from 2014 to 2016) at an urban (Seoul) and rural site (Baengnyeong) in South Korea. The average PBM concentrations in $PM_{2.5}$ samples over the entire sampling period were $12{\pm}11pg/m^3$ and $36{\pm}34pg/m^3$ for Baengnyeong and Seoul, respectively. Seasonal differences were pronounced, with concentrations being highest in winter due to local meteorological conditions (high gas-particle coefficient due to low temperature and low mixing layer height in winter) as well as seasonal factors, such as coal combustion for heating purposes in China. In Baengnyeong, the significant positive correlation of PBM with $PM_{2.5}$, air pollutants, and heavy metals suggested that coal combustion in China might be the most important source of ambient mercury in Korea. In winter, no correlation of PBM with $PM_{2.5}$, air pollutants, and heavy metals was seen in Seoul. Furthermore, Seoul showed higher $PBM/PM_{2.5}$ and $Pb/PM_{2.5}$ ratios in winter due to the strong atmospheric oxidation-reduction reaction conditions as well as local and regional PBM sources. We conclude that immediate attention must be given to addressing PBM levels in Korea, including considering it as a key component of future air quality monitoring activities and mitigation measures.