• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.143-149
• /
• 2008

A numerical study was performed for a vane of a compressor with a high-turning angle and meridional divergence. At first, the effect of the suction position was discussed. Then, the optimal suction position was applied to the cascades with the aspect ratio of 2.53 and 0.3, respectively, to get the knowledge of the effect of the endwall boundary layer removal on the secondary flow along the blade height. At last, using the critical principles of the three-dimensional separation, the topological structures of the flow patterns of the body surfaces and the separation configurations were discussed in detail. The results show that the largest reduction of the total loss can be achieved when the suction slot is near the suction side. The topological structure as well as the separation configuration varies due to boundary layer removal, which restrains the flow separation at the corner and delays or depresses the separation on the suction surface. Compared with the original cascade, the cascade with the endwall boundary layer removal has a higher blade loading along the most span. Furthermore the flow loss decreases and distributes uniformly along the span.

• 대한기계학회논문집B
• /
• 제25권12호
• /
• pp.1821-1830
• /
• 2001

The flow around free end of a finite circular cylinder (FC) embedded in an atmospheric boundary layer has been investigated experimentally. The experiments were carried out in a closed-return type subsonic wind tunnel with varying aspect ratio of the finite cylinder mounted vertically on a flat plate. The wakes behind a 2-D cylinder and a finite cylinder located in a uniform flow were measured for comparison. Reynolds number based on the cylinder diameter was about Re=20,000. A hot-wire anemometer was employed to measure the wake velocity and the mean pressure distributions on the cylinder surface were also measured. The flow past the FC free end shows a complicated three-dimensional wake structure and flow phenomenon is quite different from that of 2-D cylinder. The three-dimensional flow structure was attributed to the downwashing counter rotating vortices separated from the FC free end. As the FC aspect ratio decreases, the vortex shedding frequency decreases and the vortex formation length increases compared to that of 2-D cylinder. Due to the descending counter-rotating twin-vortex, near the FC free end, regular vortex shedding from the cylinder is suppressed and the vortex formation region is hardly distinguished. Around the center of the wake, the mean velocity for the FC located in atmospheric boundary layer has large velocity deficit compared to that of uniform flow.

• 대한기계학회논문집B
• /
• 제26권4호
• /
• pp.578-586
• /
• 2002

Flow structures around a rectangular prism have been investigated by using a PIV(Particle Image Velocimetry) technique. A thick turbulent boundary layer was generated by using spires arid roughness elements. The boundary layer thickness, displacement thickness and momentum thickness were 650mm, 117.4mm and 78mm, respectively. The ratio between the model height(40mm) and the boundary layer thickness H/$\delta$, was 0.06. The Reynolds number based on the free stream velocity and the height of the model was 7.9$\times$10$^3$. The PIV measurements were performed at three different wall normal planes. Three recirculation regions at forward facing step, top of the roof and backward facing step are clearly seen and show three dimensional features. Dramatic changes of flow patterns are observed in the wake regions in the different spanwise wall normal planes. Instead of reattachment and recirculation zone, rising streamlines are depicted at the normal planes near the side wall due to the interaction with a rising horse shoe vortex. The peak of turbulent kinetic energy occurs at the separation bubble on top of the roof and the magnitude is 2.5 times higher compared with that of the wake region.

• 지질공학
• /
• 제21권1호
• /
• pp.57-64
• /
• 2011

화강암과 안산암질 암맥이 공존하고 있는 붕괴사변을 대상으로 지질에 의한 전단강도의 차이를 반영한 3차원 사면안정해석을 수행하였다. 지질이 서로 다른 두 종류의 파괴면에 대한 전단강도를 파악하기 위하여 흙-암 경계면 직접전단시험을 수행하였고, 또한 상부 풍화토층에 대한 실내토질시험을 실시하였다. 시험결과 풍화토층에 비하여 흙-암 경계면의 전단강도가 낮게 나타났다. 사면내 지질분포의 차이가 안정성해석 결과에 영향을 주는 것을 알아보기 위하여 한계평형법을 이용한 2차원사면안정성 해석을 대표단면에서 실시하였으며, 사면내 분포지질에 따라 입력치를 다르게 할 수 있는 3차원사면안정성해석을 실시하여 2차원안정성해석과 그 결과를 비교하였다. 해석결과에 의하면 안전율이 건기시 0.92와 포화시 0.32로 모두 불안정하게 나타난 2차원해석결과와는 달리 3차원해석결과에서는 건기시에 안전율이 1.26, 포화시에 0.55로 나타났다. 이러한 결과는 사면내 지질분포를 고려할 경우 안정성 해석의 결과가 달라질 수 있음을 보여주고 있으며, 우기 직후 붕괴가 일어났던 점을 고려하면 3차원해석결과가 보다 현실적인 것으로 판단된다.

• Structural Engineering and Mechanics
• /
• 제50권6호
• /
• pp.773-796
• /
• 2014

This paper deals with free vibration analysis of continuous grading fiber reinforced (CGFR) and bi-directional FG annular sector plates on two-parameter elastic foundations under various boundary conditions, based on the three-dimensional theory of elasticity. The plates with simply supported radial edges and arbitrary boundary conditions on their circular edges are considered. A semi-analytical approach composed of differential quadrature method (DQM) and series solution is adopted to solve the equations of motion. Some new results for the natural frequencies of the plate are prepared, which include the effects of elastic coefficients of foundation, boundary conditions, material and geometrical parameters. Results indicate that the non-dimensional natural frequency parameter of a functionally graded fiber volume fraction is larger than that of a discrete laminated and close to that of a 2-layer. It results that the CGFR plate attains natural frequency higher than those of traditional discretely laminated composite ones and this can be a benefit when higher stiffness of the plate is the goal and that is due to the reduction in spatial mismatch of material properties. Moreover, it is shown that a graded ceramic volume fraction in two directions has a higher capability to reduce the natural frequency than conventional one-dimensional functionally graded material. The multidirectional graded material can likely be designed according to the actual requirement and it is a potential alternative to the unidirectional functionally graded material. The new results can be used as benchmark solutions for future researches.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.379-381
• /
• 2011

Direct numerical simulations (DNSs) of spatially developing turbulent boundary layers (TBLs) over two-dimensional (2-D) and rod and three-dimensional (3-D) cube rough walls were performed to investigate the effects of streamwise spacing on the properties of the TBL The 2-D and 3-D roughness were periodically arranged in the downstream direction with pitches of px/k=2, 3, 4, 6, 8 and 10 and for the cube, the spanwise spacing is fixed to pz/k=2 with staggered array, where px and pz are the streamwise and spanwise spacings of the roughness and k is the roughness height. Inspection of the Reynolds stresses showed that except for px/k=2 and 3 over the 2-D rough walls, the effects of the surface roughness extend to the outer layer over the 2-D and 3-D rough walls and the magnitude of the Reynolds shear stress in the outer layer is increased with proportion to px/k. However, such results are contrary to the trends of form drag, roughness junction and roughness length against px/k, which showed the maximum values at px/k=8 and 4 over the 2-D and 3-D rough walls respectively.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 학술대회
• /
• pp.262-267
• /
• 2008

Numerical investigations were performed with an external-compression inlet with a three-dimensional bump at Mach 2 to scrutinize the geometrical effects of the bump in controlling the interaction of a shock wave with a boundary layer. The inlet was designed for two oblique shock waves and a terminal normal shock wave followed by a subsonic diffuser, with a circular cross-section throughout. The bump-type inlet that replaced the aft ramp of the conventional ramp-type inlet was optimized with respect to the inlet performance parameters as well as compared with the conventional ramp-type inlet. The current numerical simulations showed that a bump-type inlet can provide an improvement in the total pressure recovery downstream of the shock wave/boundary layer interaction over a conventional ramp-type inlet.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년 추계학술대회논문집
• /
• pp.262-267
• /
• 2008

Numerical investigations were performed with an external-compression inlet with a three-dimensional bump at Mach 2 to scrutinize the geometrical effects of the bump in controlling the interaction of a shock wave with a boundary layer. The inlet was designed for two oblique shock waves and a terminal normal shock wave followed by a subsonic diffuser, with a circular cross-section throughout. The bump-type inlet that replaced the aft ramp of the conventional ramp-type inlet was optimized with respect to the inlet performance parameters as well as compared with the conventional ramp-type inlet. The current numerical simulations showed that a bump-type inlet can provide an improvement in the total pressure recovery downstream of the shock wave/boundary layer interaction over a conventional ramp-type inlet.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.610-615
• /
• 2003

This experiment has been carried out to find the structure of turbulent boundary layer with instantaneous velocity fields obtained in stream-wall-normal planes using a stereo-PIV (Particle Image Velocimetry) method. And it has been measured perpendicular plane and horizontal plane with hairpin vortex structure by Reynolds number change and made third dimension shape for section of horizontal plane through stereo-PIV. In the outer layer hairpin vortices occur in streamwise-aligned packets that propagate with small velocity dispersion. A streaky structure is composed of counter-rotating vortex. According as y+ increases, streaky structure's interval space decrease, and it shows that hairpin shape of prior research is vertified. The objective of the present research is to gain a better understanding of coherent structures in the outer of wall turbulence by experimentally examining coherent structures.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2002년도 추계학술대회 논문집
• /
• pp.117-120
• /
• 2002

An experimental research has been carried out for flow control of the shock wave/turbulent boundary-layer interaction utilizing aeroelastic mesoflaps. Various shapes and thicknesses of the mesoflap are tested to achieve different deflections of the flap, and ail the results are compared to the solid-wall reference case without flow-control mechanism. Quantitative variation of skin friction has been measured downstream of the interactions using the laser interferometer skin friction meter, and qualitative skin friction distribution has been obtained by observing the interference fringe pattern on the oil-film surface. A strong spanwise variation in the fringe patterns with a narrow region of separation near the centerline is noticed to form behind the shock structure, which phenomenon is presumed partially related to three-dimensional flow structures associated with both the sidewalls and the bottom test surface. The effect of the shape of the cavity is also observed and it is noticed that the shape of the cavity is not negligible.