• Journal of Conservation Science
• /
• v.26 no.1
• /
• pp.61-67
• /
• 2010

After selecting five types of adhesive epoxy resin for metallic cultural assets such as $Araldite^{(R)}$ rapid type, $Devcon^{(R)}$, $Araldite^{(R)}$ SV427+HV427, $CDK^{(R)}$520, $Araldite^{(R)}$ AW106+HV953 which had already been studied, this paper approached more closely the problem of yellowing and the signal of aging with time passing by connecting the problems with the safety of metallic cultural assets. The change of physical properties according to the change of state of epoxy adhesives was investigated through the change of flexural strength and the change of surface hardness by artificially providing the possible environmental change factors such as ultra-violet ray, and acid base, and how the epoxy chemically changes in its ingredients by the environment was analyzed through FT-IR. As a result of the experiment, for the most part of adhesives brought about the physical change of flexural strength, the change of surface hardness, and the chemical change of chemical ingredients as the product of alcohol, which were respectively different according to the time of ultraviolet irradiation, and acid base change. Under most of the conditions, SV427+HV427 and $CDK^{(R)}$520 were fairly stabilized under each condition of weatherability, but it seems that they should be refrained from being applied in case that the area to restore is thin and wide because the degree of flexural strength of themselves is low. Also, it is found that the preservation environment is very important not only for artifacts but also for the preservation of resins sused for preservation treatment.

• Journal of Sensor Science and Technology
• /
• v.10 no.3
• /
• pp.148-155
• /
• 2001

A pressure sensor on the tip of a catheter which is utilized to measure the in-vivo pressure in a human body was fabricated and the characteristic of the pressure sensor as measured. To fit into a catheter with 1 mm caliber, samples of $150\;{\mu}m$(thickness) ${\times}$ (600, 700, 800, 900, 1000) ${\mu}m$(width) ${\times}2\;mm$(length) was fabricated. The thicker face with $450\;{\mu}m$ thickness of SDB wafer was made thin to $134\;{\mu}m$ thickness using KOH etchant and it made possible to fabricate sensor cell with the width shorter than 1 mm. Different to the whitstone bridge sensor, we formed one piezoresistor and one reference resistor in sensor. Therefore there are possibilities of reduction of the sensitivity, then by using the simulation tool ANSYS 5.5.1, the location and the type of the piezoresistor was optimized. Another piezoresistor type of sensor which contain one longitudinal and one transverse piezoresistor was fabricated at the same time, but the sensitivity was not improved very much. To get the output versus the pressure, a constant current source and a implementation amplifier was used. As a result, the maximum sensitivity of the sensor with one piezoresistor was $1.6\;{\mu}V/V/mmHg$.

• Animal Systematics, Evolution and Diversity
• /
• v.21 no.2
• /
• pp.233-241
• /
• 2005

Two new marine sponges of family Tedaniidae, Tedania (Tedon iu) songakensis n. sp. and Tedania (Tedonia) sasuensis n. sp. were collected from Jeju Island and Chuja Island, Korea between 2004 and 2005. T. (T.) songakensis n. sp. is similar to T (T.) purpurescen Bergquist and Fromont, 1988 based on its type of spicules, but is distinguished from growth form and size of small onychaetes. The growth form of this species is massive, and is compared with thin encrusting of Tedania (T.) purpurescen. The onychaetes of the new species is twice as long as that of T. (T.) purpurescen. T. (T.) sasuensis n. sp. is closely related to T. (T.) connectens (Bronsted, 1924) in type of spicules. However, it is different in size of onychaetes and growth form. The large onychaetes of new species is larger than that of T (T.) connectens. The small onychaetes of new species is smaller than that of T. (T.) connectens. The growth form is massive in new species, but thick encrustins in T.(T.) connectens. And T. (T.) songakensis n. sp. is similar to T. (T.) sasuensis n. sp. in growth form. However, the former is widely different from the latter in shape, color and size of all spicules.

• Journal of the Korean Magnetics Society
• /
• v.14 no.1
• /
• pp.52-57
• /
• 2004

In this research, characteristics of air core rectangular spiral type inductors of ㎓ band are numerical analyzed. The basic structure of inductors is a rectangular spiral having 390${\mu}{\textrm}{m}$${\times}$390${\mu}{\textrm}{m}$ size, 5.5 turns, line width of 10 ${\mu}{\textrm}{m}$ and line space of 10 ${\mu}{\textrm}{m}$. Frequency characteristics were simulated up to 10 ㎓. The substrate was modeled as Si, Sapphire, glass and GaAs and the conductor as Cu. The thickness of the conductor was fixed at 2. The number of turns was n.5 to make the input and output terminals to be on the opposite sides. The initial inductance of the basic inductor structure was 13.0 nH, maximum inductance 60.0 nH and resonance frequency 4.25 ㎓. As the dielectric constant of the substrate was increased, the initial inductance varied only slightly, but the resonance frequency decreased considerably. As the number of turns was varied from 1.5 to 9.5, the initial inductance was increased linearly from 2.9 nH to 15.9 nH and, then, saturated at 16.9 nH. The Q factor increased only slightly. The line width and line space of inductors were varied from 5 ${\mu}{\textrm}{m}$ to 20 ${\mu}{\textrm}{m}$, which resulted in the decrease of the initial and maximum inductances. But the resonance frequency was increased. Q factor displayed an increase and a decrease, respectively, when the line width and line space were increased.

• Tuberculosis and Respiratory Diseases
• /
• v.39 no.1
• /
• pp.55-61
• /
• 1992

Background: The lung is the most common site of metastasis and usually it manifests as a single or multiple nodules in chest X-ray. But less commonly the cancer spreads through the lymphatics and X-ray shows diffuse reticulonodular densities. Sometimes, patient is presented with respiratory symptoms only with interstitial lung infiltration before the signs of primary tumor and in that cases, the differential diagnosis with other interstitial lung disease is required. We have experienced 5 such cases, who were diagnosed as lymphangitic carcinomatosis by transbronchial lung biopsy. Methods: Clinical manifestation, pulmonary function test, modified thin section CT, bronchoalveolar lavage and transbronchial lung biopsy were done. Results: The primary tumor was gastric cancer in 3, lung cancer in 2. Pulmonary function test showed restrictive pattern with low DLco in 2 patients and obstructive pattern in one. Bronchoalveolar lavage showed lymphocytosis in 4 patients and malignant cells were found in one patient. Transbronchial lung biopsy revealed malignant cells localized to the lymphatics (peribronchial, perivascular and perialveolar). Cell type was adenocarcinoma in 4 and squamous cell carcinoma in one. Conclusion: Rarely lymphangitic carcinomatosis can be presented as diffuse interstitial lung disease and easily diagnosed by transbronchial lung biopsy.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.3
• /
• pp.150-155
• /
• 1999

The Electrochemical stabilities of the Brewer-Engel type intermetallic compounds of Co-Mo $(35 wt\%)$ and Ni-Mo$(35 wt\%)$ manufactured by the arc-melting method for the hydrogen electrode of $H_2-O_2$ alkaline fuel cell were investigated. Effects of temperature and concentration on the electrochemical behavior of the electrodes in the $80^{\circ}C$ 6 N KOH solution deaerated with $N_2$ gas were studied by electrochemical methods. The effect of overpotential on the electrochemical stabilities of Co-Mo and Ni-Mo intermetallic compounds was also discussed under the normal operation condition of AFC. It was shown that Co-Mo electrode had lower electrochemical stability as compared to Ni-Mo. In the case of Co-Mo electrode, a simultaneous dissolution of cobalt and molybdenum has occurred at low anodic overpotential form equilibrium hydrogen electrode potential, but the dissolution of cobalt was serious, and Co(OH)l layer on the electrode surface formed at the high anodic overpotential. In contrast the Ni-Mo electrode had high electrochemical stability because formation of the dense and thin protective $Ni(OH)_2$ layer prevented the dissolution of molybdenum.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.4
• /
• pp.353-361
• /
• 2016

This work presents an investigation of the radio frequency characteristics of an FTLPGS (fishbone-type transmission line employing periodic ground structure) fabricated on PES (polyether sulfone) for the realization of a transparent flexible wireless communication device. According to the results, the FTLPGS on PES showed a shorter wavelength characteristic when compared with a conventional coplanar waveguide. Concretely, the wavelength of the FTLPGS was 1.91 mm at 50 GHz, which was 48.5% of the conventional coplanar waveguide. The bandwidth extraction result showed that the passband of the FTLPGS on PES was 250 GHz. Unlike conventional periodic structures, the characteristic impedance of the FTLPGS on PES also showed a very low frequency dependency. A miniaturization of the RF circuit on the PES substrate was made possible by the FTLPGS on PES having shown characteristic impedance lower than that of conventional transmission lines. These results mean that, with a broadband operation frequency, the FTLPGS on PES is a suitable construction application for the transmission line and distributed passive components.

• Applied Chemistry for Engineering
• /
• v.24 no.3
• /
• pp.320-326
• /
• 2013

In this study, various polyimide films were synthesized via low temperature cure in order to understand changes in their physical properties when using 4,4'-oxydianiline (ODA) as a diamine and dianhydride molecules with different backbones on a single diamine such as 4,4'-Oxydiphthalic anhydride (ODPA), 4,4-hexafluoroisopropylidene diphthalic dianhydride (6FDA), and 3,3', 4,4'-benzophenone tetracarboxylic dianhydride (BTDA). After the synthesis of poly(amic acid), polyimide films were fabricated by adding 1,4-diazabicyclo [2.2.2]octane (DABCO), a low-temperature catalyst, at various wt% to poly(amic acid)s. Changes of optical and thermal properties were compared and analyzed between polyimide films without catalyst and polyimide films with catalyst by FT-IR, UV-Vis transmittance, DSC/TGA, and WAXD analysis. Wide-angle X-ray diffraction (WAXD) analysis revealed that the mean intermolecular distance decreased with the use of a catalyst by the type of dianhydride. Thus, while the optical properties of the films improve by a low-temperature cure performed using a catalyst, their thermal properties decrease. These changes can be explained by the changes in the morphological structure of the films triggered by a catalyst-induced reduction in the mean intermolecular distance. Moreover, the results show that the type of dianhydride determines the degree of change in the optical and thermal properties in each types of polyimide, demonstrating that changes in the optical and thermal properties are directly associated with the backbone of the polyimide structure.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.06a
• /
• pp.135-153
• /
• 1998

Nanofiltration (NF) is a recently introduced term in membrane separation. In 1988, Eriksson was one of the first authors using the word 'nanofiltration' explicitly. Some years before, FilmTech started to use this term for their NF50 membrane which was supposed to be a very loose reverse osmosis membrane or a very tight ultrafiltration membrane. Since then, this term has been introduced to indicate a specific boundary of membrane technology in between ultrafiltration and reverse osmosis. The application fields of the NF membranes are very broad as follows: Demeneralizing water, Cleaning up contaminated groundwater, Ultrapure water production, Treatment of effleunts containing heavy metals, Offshore oil platforms, Yeast production, Pulp and paper mills, Textile production, Electroless copper plating, Cheese whey production, Cyclodextrin production, Lactose production. The earliest NF membrane was made by Cadotte et al, using piperazine and trimesoyl chloride as monomers for the formation of polyamide active layer of the composite type membrane. They coated very thin interfacially potymerized polyamide on the surface of the microporous polysulfone supports. The NF membrane exhibited low rejections for monovalent anions (chloride) and high rejections for bivalent anions (sulphate). This membrane was called NS300. Some of the earliest NF membranes, like the NF40 membrane of FilmTech, the NTR7250 of Nitto-Denko and the UTC20 and UTC60 of Toray, are formed by a comparable synthesis route as the NS300 membrane. Commercially available NF membranes nowadays are as follows: ASP35 (Advanced Membrane Technology), MPF21; MPF32 (Kiryat Weizmann), UTC20; UTC60; UTC70; UTC90 (Toray), CTA-LP; TFCS (Fluid Systems), NF45; NF70 (FilmTec), BQ01; MX07; HG01; HG19; SX01; SX10 (Osmonics), 8040-LSY-PVDI (Hydranautics), NF CA30; NF PES 10 (Hoechst), WFN0505 (Stork Friesland). The typical ones among the commercially available NF membranes are polyamide composite membrane consisting of interfacially polymerized polyamide active layer and microporous support. While showing high water fluxes and high rejections of multivalent ions and small organic molecules, these membranes have relatively low chemical stability. These membranes have low chlorine tolerance and are unstable in acid or base solution. This chemical instability is appearing to be a big obstacle for their applications. To improve the chemical stability, we have tried, in this study, to prepare chemically stable NF membranes from PVA. The ionomers and interfacially polymerized polyamide were used for the modification of'the PVA membranes. For the detail study of the active layer, homogeneous NF membranes made only from active layer materials were prepared and for the high performance, composite type NF membranes were prepared by coating the active layer materials on microporous polysulfone supports.

• Journal of the Korean Society of Food Culture
• /
• v.20 no.5
• /
• pp.627-631
• /
• 2005

Deodorized soybean oils(DSO) were obtained to 2 types. Sample 1 was carried out a general refining process, which was degumming-alkali refining-bleaching-deodorizing. Sample 2 and 3 were not general refining process, its were carried out only both decantation of insoluble impurities and batch type deodorizing(BTD). At this time, BTD was composed of 3 stages, operating differences were vacuum degree, maximum temperature, stripping steam and retention time etc. DSO obtained were appeared original physicochemical characteristics. Sample 1 had acid value 0.034, Lovibond color, 9.1Y/0.9R, peroxide value 0 and thin yellow color's soybean oil. But sample 2 had acid value, 0.078, Lovibond color, 65.0Y/18.39R/4.2B/0.1N, peroxide value, 0.7 and bright green color's soybean oil. Sample 3 had acid value, 0.072, Lovibond color, 37.3Y/3.8R/0.1B/0.1N, peroxide value 1.6 and dark brown color's soybean oil. These colorful DSO were expects as raw-materials of various seasoning oils as like pine needle and/or perilla leaf seasoning oil.