• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2005년도 춘계학술발표회
• /
• pp.141-146
• /
• 2005

선체는 기본적으로 판부재들의 조합으로 구성되어 있으며 이들중 상당수는 유공판(Perforated plate)이다. 선체에 설치된 유공판으로서는 선체 상갑판 해치(하역시설로 사용), 선저부의 거더와 플로어(중량경감과 선박 건조 및 검사시 통로확보용), 다이어프램(중량경감 및 파이프 관통의 목적)둥이 있다. 이들 유공판에 하중이 작용하면 좌굴과 최종강도 특성이 크게 변화할 뿐만 아니라 수반되는 면내응력도 재 분포하게 되어 심각한 강도문제를 야기 시킬 수 있다. 실적선에서는 유공주위에 스티프너 보강을 통하여 취약한 좌굴강도 보완하고 있으며, 유공을 고려한 최적의 유공보강판 모델을 적용한 좌굴강도 및 최종강도를 파악할 필요성이 대두시 되고 있다. 이와 같은 측면에서 각 조선소에서는 각국 선급들이 제시하는 유공판의 좌굴설계식을 사용하여 강도계산을 하고 있으나 임의의 유공크기에 대찬 좌굴강도 및 최종강도 평가법을 찾기란 매우 어려운 일이다. 본 연구에서는 실선에서 사용중인 유공보강판의 모델을 조사하여 비선형유한요소법을 적용하여 면내 압축하중이 작용하는 경우에 대해서 유공의 크기와 웹 치수를 변화시켜가며, 최종강도 시리즈 해석을 수행하고 압축최종강도에 미치는 영향을 검토하였다.

• Steel and Composite Structures
• /
• 제13권3호
• /
• pp.239-258
• /
• 2012

In this paper, experimental investigations on high strength steel (HSS) stud connected steel-concrete composite (SCC) girders to understand the effect of shear connector density on their flexural behaviour is presented. SCC girder specimens were designed for three different shear capacities (100%, 85%, and 70%), by varying the number of stud connectors in the shear span. Three SCC girder specimens were tested under monotonic/quasi-static loading, while three similar girder specimens were subjected to non-reversal cyclic loading under simply supported end conditions. Details of casting the specimens, experimental set-up, and method of testing, instrumentation for the measurement of deflection, interface-slip and strain are discussed. It is found that SCC girder specimen designed for full shear capacity exhibits interface slip for loads beyond 25% of the ultimate load capacity. Specimens with lesser degree of shear connection show lower values of load at initiation of slip. Very good ductility is exhibited by all the HSS stud connected SCC girder specimens. It is observed that the ultimate moment of resistance as well as ductility gets reduced for HSS stud connected SCC girder with reduction in stud shear connector density. Efficiency factor indicating the effectiveness of high strength stud connectors in resisting interface forces is estimated to be 0.8 from the analysis. Failure mode is primarily flexure with fracturing of stud connectors and characterised by flexural cracking and crushing of concrete at top in the pure bending region. Local buckling in the top flange of steel beam was also observed at the loads near to failure, which is influenced by spacing of studs and top flange thickness of rolled steel section. One of the recommendations is that the ultimate load capacity can be limited to 1.5 times the plastic moment capacity of the section such that the post peak load reduction is kept within limits. Load-deflection behaviour for monotonic tests compared well with the envelope of load-deflection curves for cyclic tests. It is concluded from the experimental investigations that use of HSS studs will reduce their numbers for given loading, which is advantageous in case of long spans. Buckling of top flange of rolled section is observed at failure stage. Provision of lips in the top flange is suggested to avoid this buckling. This is possible in case of longer spans, where normally built-up sections are used.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권5호
• /
• pp.461-466
• /
• 2013

본 논문은 조선해양 구조물 주판의 맞대기용접 수축에 대한 특성을 연구하였다. 주판의 맞대기 용접은 입 열과 냉각과정에서 수축 변형이 일어나 최종 완성된 모재의 치수와 설계 치수가 다르게 된다. 이는 선박의 블록 생산 품질 불량으로서 교정 작업이 필요하며 생산성 향상의 저해요인이다. 이에 대형 구조물 주판의 맞대기용접 수축 변형에 관한 실험을 통하여 I, Y, V 형상의 용접잔류응력 수축 변형 데이터를 확보하고 두께 11 t ~ 21.5 t 범위에서는 1 ~ 2 mm의 한정된 범위의 수축 량이 균일하게 나타나는 특징과 용접부의 열전달 영향이 Seam Line 한쪽을 기준으로 최대 약 1000 mm 이내에 국한되어 모재의 자중이 수축 량에 미치는 영향은 크지 않았고 또한 수축 변형을 최소화하기 위해 설계단계에서 Groove 형상에 따라 수축마진을 다르게 적용해야 함을 알 수 있었다.

• 한국자기학회지
• /
• 제16권6호
• /
• pp.279-282
• /
• 2006

비정질 강자성 NiFeSiB 자유층을 갖는 자기터널접합 (MTJ)에 대하여 연구하였다. 비정질 자유층이 MTJ의 스위칭 특성에 미치는 영향을 알아보는데 역점을 두어 기존의 CoFe와 NiFe층 대신에 NiFeSiB 자성층을 사용하였다. $Ni_{16}Fe_{62}Si_{8}B_{14}$는 $Co_{90}Fe_{10}$보다 더 낮은 포화자화도 ($M_{s}:\;800\;emu/cm^{3}$) 그리고 $Ni_{80}Fe_{20}$보다 더 높은 이방성 상수 ($K_{u}:\;2700\;erg/cm^{3}$)를 갖는다. $Si/SiO_{2}/Ta$ 45/Ru 9.5/IrMn 10/CoFe $7/AlO_{x}/CoFeSiB\;(t)/Ru\;60\;(nm)$ 구조는 그 자체의 낮은 포화자화도와 높은 일축 이방성을 가짐으로 인하여 보자력($H_{c}$)을 감소시키고 스위칭 각형을 증가시키게 함으로서 MTJ의 스위칭 특성에 유리한 것으로 조사되었다. 더욱이 미소두께(1 nm)의 CoFe층을 터널장벽/NiFeSiB 경계면에 삽입하면 TMR비와 스위칭 각형이 증가하고 개선되었다.

• 한국자기학회지
• /
• 제21권2호
• /
• pp.77-82
• /
• 2011

우리 삶의 질을 좌우하는 전자기 기기의 고기능화, 자동화, 소형화 추이에 따라 사용량이 급격히 증가하고 있는 연자성 소재로서 가장 널리 사용되고 있는 전기강판과 에너지 고효율화라는 시대의 요구에 따라 새롭게 부상되고 있는 연자성 복합 분말 소재에 대해 각 연자성 소재 분야에서 철손 제어 인자 및 이들 인자들의 제어 방안에 대해 문헌을 고찰했다. 전기강판에서는 히스테리시스 손실을 낮추기 위해 정련공정을 통해 자구이동을 방해하는 결함을 제거하고 결정립의 크기를 최적화하고 있으며, 와전류 손실의 감소를 위해 합금첨가원소를 통해 비저항을 높이고 판재의 두께를 박판화하고 있다. 이와 동시에 코팅을 통해 자구의 이동이 용이하도록 응력의 방향 및 크기를 제어하며, 압연기술과 열처리 기술을 통해 집합조직을 최적화하여 고투자율 및 저철손을 동시에 충족시켜 나가고 있다. 연자성 복합 분말 소재의 경우, 분말 표면의 복합화를 통해 철계 조성, 코팅, 윤활재 및 바인더, 성형 및 열처리 조건 등에 복합적으로 의존하는 연자성 코어의 최종 자기특성을 제어하고 있다. 온간 및 다단 성형과 같은 새로운 성형공정, 2단 소둔/자성 열처리와 같은 소둔 조건, 나노결정질, 비정질 및 벌크 비정질 등과 같은 새로운 조성, 적절한 코팅층의 변수들을 최적화할 경우, 연자성 복합 소재의 자성특성은 향상될 것으로 기대된다.

• 한국식품저장유통학회지
• /
• 제14권4호
• /
• pp.364-368
• /
• 2007

가공이나 저장 중 쉽게 산화되는 특성을 갖는 비타민 C의 안정성과 가공적성을 향상시키고자 Zein-DP와 HPMC-FCC를 코팅제로 한 유동층 코팅법을 이용하여 코팅한 비타민 C 분말의 품질 특성에 대하여 조사하였다. 유동층 코팅은 비타민 C의 입자크기($80{\sim}100\;mesh,\;100{\sim}140\;mesh$)와 코팅액의 혼합비(1:1.6, 1:2.5, 1:3(w/w))를 달리하여 실시하였다. 코팅효율은 $80{\sim}100\;mesh$의 경우가 $100{\sim}140\;mesh$보다 높았고 코팅액의 혼합량이 많을수록 감소함을 보였다. 코팅된 필름의 두께는 $80{\sim}100\;mesh$의 경우가 $100{\sim}140\;mesh$보다 두꺼웠으며, 코팅된 입자의 입도분포도는 코팅액 혼합비 1:3에서 가장 좁았다. 코팅분말의 DPPH 소거능은 코팅 전 입자크기와 코팅액 혼합비에 따른 큰 차이를 보이지 않았다. 상기의 코팅된 분말의 품질 특성에 코팅물질의 종류는 거의 영향을 미치지 않았다. 이로써 비타민 C의 유동층 코팅에 적합한 조건으로 비타민 C의 입자크기는 $80{\sim}100\;mesh$, 비타민 C와 코팅 액의 혼합비는 1:3(w/w)으로 판단된다.

• Journal of Acupuncture Research
• /
• 제25권4호
• /
• pp.81-94
• /
• 2008

Rheumatoid arthritis(RA) is a general, chronic, inflammatory and auto-immune disease and it can lead to joint edema, pain, stiffness which are caused by an inflammation in synovium covering our joints. Ulmus davidiana Planchon is a traditional herb used for the treatment on various inflammations, gastrointestinal trouble, ENT(ear, nose, and throat) disease, edema, cancer etc. and it works effectively on arthritis as well. In these study to search for the treatment efficacy of Ulmus davidiana Planchon in RA, I measure manifestation of cytokine gene in synoviocyte treated with Ulmus davidiana Planchon herbal acupuncture and in EL-4 cell, manifestation of cytokine gene cell related to T-cell. And after Ulmus davidiana Planchon herbal acupuncture treatment in Collagen induced arthritis(CIA) which has been known by a general model of RA, DBA mice, I observed foot thickness, general shape of synovium, early cytokine induce CIA and, generation and mutation of cytokine related to the control of T-cell specialization. It comes to conclusion as belows. 1. In synovium treated with Ulmus davidiana Planchon herbal acupuncture, there was the decrease in MIF mRNA does-dependently. Incase of CIA mice treated with Ulmus davidiana Planchon herbal acupuncture, there were the decrease in the damage in synovium and generation of the MIF which is related to induction of the early RA cytokine and IL-6 proinflammatory cytokine. 2. In case of EL-4 treated with Ulmus davidiana Planchon herbal acupuncture, there were decrease in the manifestation of the IL-2 mRNA, but the increase in the manifestation of the IL-4 does-dependently. 3. In the synovium of CIA mice treated with Ulmus davidiana Planchon herbal acupuncture, there were the decrease in generation of IL-2, IL-12 and CD-28, but the increase in generation of IL-4. These result suggest that Ulmus davidiana Planchon can block the process of the early RA by Inhibiting MIF activation, and mitigate Rheumatoid Arthritis by controlling Tcell specialization.

• 대한치과교정학회지
• /
• 제41권5호
• /
• pp.354-360
• /
• 2011

Objective: To investigate the effects of different pilot-drilling methods on the biomechanical stability of self-tapping mini-implant systems at the time of placement in and removal from artificial bone blocks. Methods: Two types of artificial bone blocks (2-mm and 4-mm, 102-pounds per cubic foot [102-PCF] polyurethane foam layered over 100-mm, 40-PCF polyurethane foam) were custom-fabricated. Eight mini-implants were placed using the conventional motor-driven pilot-drilling method and another 8 mini-implants were placed using a novel manual pilot-drilling method (using a manual drill) within each of the 2-mm and 4-mm layered blocks. The maximum torque values at insertion and removal of the mini-implants were measured, and the total energy was calculated. The data were statistically analyzed using linear regression analysis. Results: The maximum insertion torque was similar regardless of block thickness or pilot-drilling method. Regardless of the pilot-drilling method, the maximum removal torque for the 4-mm block was statistically higher than that for the 2-mm block. For a given block, the total energy at both insertion and removal of the mini-implant for the manual pilot-drilling method were statistically higher than those for the motor-driven pilot-drilling method. Further, the total energies at removal for the 2-mm block was higher than that for the 4-mm block, but the energies at insertion were not influenced by the type of bone blocks. Conclusions: During the insertion and removal of mini-implants in artificial bone blocks, the effect of the manual pilot-drilling method on energy usage was similar to that of the conventional, motor-driven pilot-drilling method.

• Journal of Periodontal and Implant Science
• /
• 제36권2호
• /
• pp.273-288
• /
• 2006

The purpose of this study was to evaluate exophytically vertical bone formation in rabbit calvaria by the concept of guided bone regeneration with a custom-made porous titanium membrane combined with bone graft materials. For this purpose, a total of 12 rabbits were used, and decorticated calvaria were created with round carbide bur to promote bleeding and blood clot formation in the wound area. Porous titanium membranes (0.5 mm in pore diameter, 10 mm in one side, 2 mm in inner height) were placed on the decorticated calvaria, fixed with metal pins and covered with full-thickness flap. Experimental group I was treated as titanium membrane only. Experimental group II, III, IV was treated as titanium membrane with BBM, titanium membrane with DFDB and titanium membrane with FDB. The animals were sacrificed at 8 and 12 weeks after surgery, and new bone formation was assessed by histomorphometric as well as statistical analysis. 1. Porous titanium membrane was biocompatable and capable of maintaining the regeneration space. 2. At 8 and 12 weeks, all groups demonstrated exophytic bone formation and there was a statistical significant difference among different groups only at 12 weeks. 3. The DFDB group revealed the most new bone formation compared to other groups (p<0.05). 4. At 12 weeks, DFDB and FDB groups showed the most significant resorption of graft materials (p<0.05). 5. The BBM was not resorbed at all until 12 weeks. 6. The fixation metal pin revealed excellent effect in peripheral sealing. On the basis of these findings, we conclude that a porous titanium membrane may be used as an augmentation membrane for guided bone regeneration, and DFDB as an effective bone forming graft material. The fixation of the membrane with pin will be helpful in GBR technique. However, further study is required to examine their efficacy in the intraoral experiments.

• 대한치과보철학회지
• /
• 제41권2호
• /
• pp.128-135
• /
• 2003

Statement of problem : Implant screw loosening remains a problem in implant prosthodontics. Some abutment screws with treated surfaces were introduced to prevent screw loosening and to increase preload. DLC(Diamond Like Carbon) film has similar properties on hardness, wear resistance, chemical stability, biocompatibility as real diamond materials. Purpose : The purpose of this study was to investigate the effect of lubricant layer on abutment screw and to discriminate more effective method between soft lubricant and hard lubricant to prevent screw loosening. Material and method : In this study, $1{\mu}m$ thickness DLC was used as protective, lubricating layer of titanium screws and 3 times removal torque was measured on the abutment screws to investigate the difference in 10 coated and 10 non-coated abutment screws. Results : The results indicated that the implants with DLC coating group were not more resistant to the applied force in screw loosening. At 32Ncm, the 3 times removal torque in DLC group were $27.75{\pm}2.89,\;25.85{\pm}2.35$ and $26.2{\pm}2.57$. The removal torque in no-coated abutment screws were $27.85{\pm}4.23,\;27.35{\pm}2.81$ and $27.9{\pm}2.31$, respectively. Conclusion : The lubricant layer used in this study was Diamond Like Carbon(DLC) and it have a properties of hard and stable layer. The DLC coating layer was hard enough to prevent distortion of screws in the repeated unscrewing procedure in clinical situation. The reduced friction coefficient in hard DLC layer was not effective to prevent screw loosening.