• Journal of the Korean Society of Combustion
• /
• v.20 no.4
• /
• pp.10-18
• /
• 2015

Combustion instability is a major issue in design and maintenance of gas turbine combustors for efficient operation with low emissions. With the thermoacoustic view point the instability is induced by the interaction of the unsteady heat release of the combustion process and the change in the acoustic pressure in the combustion chamber. In an effort to study the combustion dynamics of gas turbine combustors, Morgans et al (2014) have developed OSCILOS (open source combustion instability low order simulator) code and it is currently available online. In this study the code has been utilized to predict the combustion instability of a reported case for lean premixed gas turbine combustion, and then its prediction results have been compared with the corresponding experimental data. It turned out that both the predicted and the experimental combustion instability results agree well. Further the effects of some typical inlet acoustic boundary conditions on the prediction have been investigated briefly. It is believed that the validity and effectiveness of the open source code is reconfirmed through this benchmark test.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.9
• /
• pp.659-668
• /
• 2008

Combustion instability has been considered as very important issue for developing gas turbine and rocket engine. There is a need for fundamental understanding of combustion instability. In this study, combustion instability was numerically and experimentally investigated in a dump combustor with bluff body. The fuel and air mixture had overall equivalence ratio of 0.9 and was injected toward dump combustor. The pressure oscillation with approximately 256Hz was experimentally obtained. For numerical simulation, the standard k-$\varepsilon$ model was used for turbulence and the hybrid combustion model (eddy dissipation model and kinetically controlled model) was applied. After calculating steady solution, unsteady calculation was performed with forcing small perturbation on initial that solution. Pressure amplitude and frequency measured by pressure sensor is nearly the same as those predicted by numerical simulation. Furthermore, it is clear that a combustion instability involving vortex shedding is affected by acoustic-vortex-combustion interaction. The phase difference between the pressure and velocity is $\pi$/2, and that between the pressure and heat release rate is in excitation range described by Rayleigh, which is obvious that combustion instability for the bluff body combustor meets thermoacoustic instability criterion.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.896-904
• /
• 2017

Lean premixed combustion was successful in meeting current NOx emission regulations. However, these often leads to combustion instability. This phenomena results from the feedback relationship between heat release perturbations and acoustic pressure oscillations in the combustor. Researches on the combustion instability in an annular combustor have recently received great attention due to the enhanced NOx requirement in aero-engines. In this study, the thermoacoustic network model has been developed in order to calculate the acoustics for longitudinal as well as circumferential modes in the annular combustor. The combustion model in the network model is calculated by flame transfer function(FTF). Numerical and analytical results are compared to an measurement data.

• Journal of the Korean Society of Combustion
• /
• v.23 no.1
• /
• pp.13-20
• /
• 2018

Transverse acoustic mode in annular combustion chambers affects air-fuel mixing characteristics in the nozzle and can result in heat release fluctuations in the combustor. In addition, the acoustic mode coupling between the nozzle and the combustion chamber is one of the key parameters determining combustion instability phenomenon in the annular combustor. In this study, acoustic coupling between the nozzle and annular combustor was numerically analyzed using 3D-based in house FEM code. As a result, it was found that the acoustic mode inside the combustion chamber at anti-node locations of the transverse mode was strongly influenced by the nozzle inlet boundary conditions.

• Journal of ILASS-Korea
• /
• v.24 no.2
• /
• pp.58-65
• /
• 2019

A 3D FEM (Finite Element Method) based Helmholtz solver has been commonly used to characterize fundamental acoustic behavior and investigate dynamic instability features in many combustion systems. In this approach, a geometrical simplification of the target system has been generally made in order to reduce computational time and cost because a real combustor and fuel nozzle have a very complicated flow passage. The feasibility of these simplifications is quantitatively investigated in a small aero gas turbine nozzle in term of acoustic characteristics. It is found that the simplification in a nozzle geometry during the 3D FEM analysis process has no great influence on the acoustic modeling results, while the calculation complexity can be improved for a similar modeling accuracy.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.6
• /
• pp.49-56
• /
• 2017

The current study has developed an in-house 3D FEM code in order to model thermoacoustic problems in an annular system and compared the acoustic field calculation results with measured ones from a benchmark combustor. From the comparison of calculation results with the measured data, the current acoustic code could successfully capture the various acoustic mode found in the annular system. In addition, it was found that the transverse waves in the combustor were strongly affected by the nozzle acoustic impedances, as well, the pressure distributions were closely related with the combustor acoustic pressure field.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.2
• /
• pp.38-45
• /
• 2019

The present work suggests a numerical approach using a thermoacoustic network model for the eigenvalue calculation of thermoacoustic instability problems in an aero gas turbine combustor. The model is developed based on the conservation laws for mass, momentum, and energy between acoustic network elements with an area change. Acoustic field in a practical aero gas turbine combustor which has a complicated flow path is analyzed using the current model. The predictive capabilities of the current modeling approach are compared with the acoustic characteristics calculated using Helmholtz solver based on 3D finite element method(FEM).

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.3
• /
• pp.72-80
• /
• 2018

Combustion instabilities are caused by the feedback relationship between heat release perturbations and acoustic pressure oscillations in the combustor. Studies on the combustion instability in an annular combustor have recently received great attention due to the enhanced NOx requirement in aero-engines. In this study, a thermoacoustic network model was developed in order to calculate the acoustic characteristics for various modes in the annular combustor. The network model is combined with flame transfer function(FTF) in order to calculate the stability of the combustor. Numerical results are compared with measurement data.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.4
• /
• pp.1-9
• /
• 2022

In the current study, in order to understand the dynamic response characteristics of the system according to the external acoustic forcing, a numerical approach was developed by adding an sign-sweep forcing function to the existing network model. Through this model, the sensitivity of frequency and pressure amplitude changes according to system parameters such as the physical dimensions and boundary conditions of the target combustor was analyzed in a wide frequency range. Analysis results of dynamic response characteristics of the target combustor are shown that the frequency regime with high dynamic pressure response was similar to the instability frequency range measured in the same combustor, and in particular, the response of the system depends greatly on the location of the acoustic forcing source term.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.11
• /
• pp.783-789
• /
• 2022

In a recent study, it was observed that the combustion gas entering the post chamber of a hybrid rocket contains vortices with very small size and high frequency characteristics. In addition, it was observed that small vortices collided with the nozzle wall to create a counter-flow, resulting in additional combustion with ignition delay. This study investigated the physical relationship between ignition delay induced by the counter-flow and the formation of beating pressure. To do this, a newly modified model was proposed by including ignition delay in the existing energy kicked oscillator model proposed by Culick. Numerical results show that the ignition delay is an important factor in determining the occurrence of the combustion pressure beats through the periodic formation of thermoacoustic coupling. In addition, when the ignition delay was reduced by increasing the post chamber length, the phase difference between the energy kick and the pressure generation was increased, the periodic pressure beats did not occur at all.