• 대한기계학회논문집A
• /
• 제20권2호
• /
• pp.488-499
• /
• 1996

SMC(Sheet molding compound) is a thermosetting material reinforced with chopped fiberglass. The compression molding of SMC was analyzed based on a rigid thermo-viscoplastic approach using a three dimensional finite element program coupled with temperatures. Only the temperature analysis part was tested in this paper by solving one-dimensional heat transfer problem and comparing with the exact solutions available in the literature. Based on this comparison the program was proved to be valid and was further applied in solving compression molding of SMC between flat dies. To investigate the usefulness of a rigid thermo-viscoplastic approach in the compression molding analysis of SMC charge, compression of rectangular shaped SMC charge at plane strain and three dimensionalde formation condition was analyzed under the same condition as given in the literature. From this comparison it was found out that the rigid thermo-viscoplastic approach was useful in analyzing SMC compression molding between flat dies.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1992년도 춘계학술대회 논문집 92
• /
• pp.177-200
• /
• 1992

A thermo-viscoplastic finite element program was developed to analyze the compression molding of SMC process. Deformation of the material was modelled by using the flow-rule. Heat balance during the process was coupled to the deformation. In the cure study, a kinetic model was adopted to describe the cure behavior. The numerical kinetic model was integrated with the thermo-viscoplastic numerical analysis by adding heat generation due to the chemical reaction of the workpiece in the heat transfer analysis. The integrated finite element program can simulate a whole sequential molding process including deformation, heat transfer, and chemical reaction. A practical SMC molding process with T-shaped substructure was simulated. The simulated results showed good agreements with experiments.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.136-142
• /
• 2001

Recently, a much amount of attention has been paid not only to produce products with precise dimensional accuracy, but also to predict and control the microstructural evolution and mechanical properties of parts. Especially, to do the latter through computer simulation, the history of states factors influencing on these evolution such as temperature, strain, strain rate etc., should be calculated and a appropriate mathematical models for the prediction of microstructural evolution must be developed. Thus, in this study thermo-viscoplastic finite element program including the model for predicting microstructural has been developed. Also for the verification of developed program warm forging process for the rotor pole was simulated and the comparison between the results calculated and ones in the literature was made.

• 대한기계학회논문집A
• /
• 제26권10호
• /
• pp.2211-2218
• /
• 2002

In this study, an optimal design study has been made to determine dimensions of die and multi stress rings for extrusion process. For this purpose, a thermo-rigid-viscoplastic finite element program, CAMPform, was used fur forming analysis of extrusion process and a developed elastic finite element program fur elastic stress analysis of the die set including stress rings. And an optimization program, DOT, was employed for the optimization analysis. From this investigation, it was found out that the amount of shrink fitting incurred by the order of assembly of the die set should be taken into account for optimization when the multi stress rings are used in practice. In addition, it is construed that the proposed design method can be beneficial fur improving the tool life of cold extrusion die set.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.159-164
• /
• 1997

The optimal conditions were investigated in order to manufacture the light automotive body parts using the semi-solid forging process by the finite element nalysis. Considering about macro-segregation cause to difference of relative velocity between solid phase and liquid phase, solidificational phenomenon cause to heat transfer from die and export of the latent heat, so solid fraction updating algorithm can be proposed. The rigid thermo-viscoplastic finite element analysis was carried out according to die temperature with proposed algorithm, so availability of forming part were understood. The finite element program can be used to the analysis of semi solid forging process.

• 대한기계학회논문집A
• /
• 제24권11호
• /
• pp.2836-2844
• /
• 2000

Thickness control of hot-rolled strips has become an important issue in recent years because of the need for improving the quality of the hot-rolled strip. In this study, a modifying method of rolling force set-up with consideration of spread was developed to improve the thickness uniformity at the finishing rolling units in hot rolling. Through the analysis of real production data it was found that the accuracy of the rolling force determined from the finishing mill set-up (FSU) model dominantly governed the thickness uniformity in rolled plates at the front. Based on this analysis , several examples were selected to calculate the spread of rolled plate using three dimensional rigid thermo-viscoplastic finite element program. FE analysis results were used to train the neural network system that can predict the spread hot-rolled plate and the rolling force was modified based on the predicted value of spread. The modified rolling forces were closer to the measured rolling force so it can be expected that the accuracy of thickness uniformity of hot-rolled plate will be improved.