• Applied Chemistry for Engineering
• /
• v.32 no.2
• /
• pp.143-148
• /
• 2021

A thermally conductive 200 ㎛ thick polyimide-based film was made from a polyamic acid (PAA) precursor containing graphene prepared from graphite rod using an electrostatic discharge method in order to improve the thermal conductivity and expand the applicability of polyimide (PI) film. Properties of graphene produced by electrostatic discharge were measured by Raman spectroscopy, transmission electron microscopy and X-ray photoelectron spectroscopy (XPS). As a result of Raman spectrum and XPS analyses of as-prepared graphene, the ID/IG ratio was 0.138 and C/O value was 24.91 which are excellent structural and surface chemical properties. Moreover, thermal conductivities of polyimide films increased exponentially according to graphene contents but when the graphene content exceeded 40%, the polyimide film could not maintain its shape. The thermal conductivity of carbonized PI film made from PAA containing 40 wt% of graphene was 51 W/mK which is greatly enhanced from the pristine carbonized PI film (1.9 W/mK). This result could be originated from superior properties of graphene prepared from the electrostatic discharge method.

• Composites Research
• /
• v.33 no.5
• /
• pp.268-274
• /
• 2020

This paper analyzed the degradation behaviors of silica nano epoxy composite based on the isoconversional method. The size of the silica nano particle was about 12 nm and the particles were mixed by three different weight ratios to make the degradation test samples. The thermogravimetric analyses were performed under six different temperature increase rates to measure the weight changes. Four different methods, Friedman, Flynn-Wall-Ozawa, Kissinger and DAEM (Distributed Activation Energy Method), were employed to calculate the activation energies depending on the conversion ratios, and their calculation results were compared. The results represented that the activation energy was increased when the silica nano particles were mixed up to 10%, indicating the definite contribution of the particles to the degradation behavior enhancements. However, the enhancement was not proportional to the particle mixture ratio by demonstrating the similar activation energies between 10% and 18% samples. The calculation results by the different methods were also compared and discussed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.11
• /
• pp.1004-1009
• /
• 2012

Carbon nanotube are nanostructure with extraordinary field emission properties like high current density, low driving voltage and long time stability, because of their high electrical conductivity, high aspect ratio for geometrical field enhancement and superior thermal stability. But, there is some problem to mate metal and carbon nanotube, we have resolved this problem by using interfacial graphene. This approach takes advantage of superior electric and thermal conductivity between metal and carbon nanotube and shows superior performance compared to the existing field emitters. This result shows that such a carbon nanotube emitter in a stage where it can be used for Field Emission Electric Propulsion (FEEP).

• Journal of IKEEE
• /
• v.13 no.1
• /
• pp.57-64
• /
• 2009

The optoelectrical characteristics of the ZnO nanoparticles (NPs) annealed in vacuum or oxygen condition from $200^{\circ}C$ to $600^{\circ}C$ were examined. Increased on-off ratio (or, the ratio of photocurrent to dark current) was observed when they were annealed at $300^{\circ}C$, $400^{\circ}C$ and $500^{\circ}C$ with the values enhanced about 4 orders compared to the as-prepared ZnO NPs in both annealing conditions, while the maximum efficiency was shown at the annealing temperature of $600^{\circ}C$ for the ZnO NPs annealed in vacuum with the value of 29.8 mA/W and at the temperature of $500^{\circ}C$ for those annealed in oxygen condition with the value of 40.3 mA/W. Photoresponse behavior of the ZnO NPs annealed in oxygen showed the sharp increase right after the ir exposure to the light followed by the slow decay and saturation during steady illumination, differing from the ZnO NPs annealed in vacuum which only exhibited the gradual increase. This difference occurred due to the curing effect of the oxygen vacancies. SEM images indicated no change in their morphologies with annealing, indicating the change in their internal structures by annealing, and most remarkably at $600^{\circ}C$. As for their photoluminescence(PL) spectra, the decrease of the deep-level(DL) emission was observed when they were annealed in oxygen at $400^{\circ}C$, and not at $200^{\circ}C$ and $600^{\circ}C$.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.3
• /
• pp.343-350
• /
• 2012

A planar solid oxide fuel cell (PSOFC) is studied in its application in a high-temperature stationary power plant. Even though PSOFCs with external reformers are designed for application from the distributed power source to the central power plant, such PSOFCs may sacrifice more system efficiency than internally reformed SOFCs. In this study, modeling of the PSOFC with an external reformer was developed to analyze the feasibility of thermal energy utilization for the external reformer. The PSOFC system model includes the stack, reformer, burner, heat exchanger, blower, pump, PID controller, 3-way valve, reactor, mixer, and steam separator. The model was developed under the Matlab/Simulink environment with Thermolib$^{(R)}$ modules. The model was used to study the system performance according to its configuration. Three configurations of the SOFC system were selected for the comparison of the system performance. The system configuration considered the cathode recirculation, thermal sources for the external reformer, heat-up of operating gases, and condensate anode off-gas for the enhancement of the fuel concentration. The simulation results show that the magnitude of the electric efficiency of the PSOFC system for Case 2 is 12.13% higher than that for Case 1 (reference case), and the thermal efficiency of the PSOFC system for Case 3 is 76.12%, which is the highest of all the cases investigated.

• Nuclear Engineering and Technology
• /
• v.37 no.5
• /
• pp.479-490
• /
• 2005

The thermalhydraulic performance of a CANDU-6 reactor loaded with various CANFLEX fuel bundles is evaluated by the NUCIRC code, which is incorporated with recent models of pressure drop and critical heat flux (CHF) predictions based on high-pressure steam-water tests for the CANFLEX bundle as well as a 37-element bundle. The distributions of channel flow rate, channel exit quality, critical channel power (CCP), and critical power ratio (CPR) for the CANFLEX bundles (with natural or recycled uranium fuel) in the CANDU-6 reactor fuel channel are calculated by the code. The effects of axial and radial heat flux on CCP are evaluated by assuming that the recycled uranium fuel (CANFLEX-RU) has the same geometric data as the natural uranium fuel bundle (CANFLEX-NU), but a different power distribution due to different fuel composition and refueling scheme. In addition, the effects of pressure tube creep and bearing-pad height are examined by comparing various results of uncrept, and $3.3\%\;and\;5.1\%$ crept channels loaded with CANFLEX bundles with 1.4 mm or 1.7 mm high bearing-pads with those of the 37-element bundle. The distributions of the channel flow rate and CCP for the CANFLEX-NU or -RU bundle show a typical trend for a CANDU-6 reactor channel, and the CPRs are maintained above at least 1.444 (NU) or 1.455 (RU) in the uncrept channel. The enhanced CHF of the CANFLEX bundle (particularly with 1.7mm height bearing-pads) produces a higher thermal margin and considerably less sensitivity to CCP reduction due to the pressure tube creep than the 37-element bundle. The CCP enhancement due to the raised bearing-pads is estimated to be about $3\%\~5\%$ for the CANFLEX-NU and $2\%\~6\%$ for the CANFLEX-RU bundle, respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.7 no.1
• /
• pp.63-70
• /
• 1990

Influence of mixing ratio of blending oil (rice bran oil : RBD palm olein = 1 : 1, 1 : 4 mixture: w/w) and natural tocopherol, citric acid, and sodium polyphosphate on enhancement of oxidation stability of blending oil under the condition of tap water infulx(1 ml/min/200g oil) were compared by AOM test after heating these system at l80$^{\circ}C$. In addition, the effects of tocopherol, and synergist on oxidition stability were also tested with potato chips fried with blending oil(1 : 4 mixture). The result obtained were as followes; 1. The test of RBD palm olein addition of 50% and 80% against rice bran oil on oxidation stability showed that the higher the palm olein contents in blending oil, the higher the oxidation stability. 2. The test of oxidation stability, adding l00ppm, 200ppm and 400ppm of natural tocopherol in two different types of blending oils, A(1 : 1 mixture) and B(1 : 4 mixture), disclosed that blending oil B was more positively effective, and this trend was superior at 200ppm level particularly, Furthermore, oxidation stability was enhanced remarkably upon addition of 100ppm of natural tocopherol, and 50ppm of citric acid together with 50ppm, 100ppm and 200ppm of sodium polyphosphate in general. Especially, 200ppm of sodium polyphosphate addition induced the most synergetic effect on oxidation stability showing as much as 3 times compare to control. 3. The results of oxidation stability obtained by peroxide value on potato chips fried with blending oil (1:4 mixture} added tocopherol, citric acid and sodium polyphosphate and preserved at $60^{\circ}C$ revealed that addition of tocopherol and 50ppm of citric acid together with 200ppm of sodium polyphosphate treatment was the most synergistic coinciding with AOM test results.

• Radiation Oncology Journal
• /
• v.8 no.1
• /
• pp.17-27
• /
• 1990

The effects of both hyperthermia alone and X-ray irradiation combined with hyperthermia on rat testis have been investigated. The histological changes were observed on 15 and 30 days after treatment. There was no histological change of rat testis by hyperthermia alone. The earliest change by X-ray irradiation was the degeneration of the spermatogonia of the seminiferous tubule, which was appeared in 2 Gy group. Necrosis of the spermatogonia was severe in 6 Gy group and complete atrophy was developed in 8 Gy group. With increased dose of radiation, the degree of changes of tubules was increased. In combined group of X-ray irradiation and hyperthermia, the histological change of the seminiferous tubule was more severe than X-ray alone group. Necrosis and atrophy of the spermatogonia were appeared in 2 Gy and complete atrophy of spermatogonia was seen in 6 Gy group. Thermal enhancement ratio (calculated at the complete atrophy of the spermatogonia) was 1.3 in this experiment. There was no difference in observation time inverval between 15 and 30 days after each treatment in all groups.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.4
• /
• pp.40-49
• /
• 2016

This study aims to confirm the characteristics of low swirl combustion at our low swirl model combustor. To do it, it is experimentally conducted by evaluating the flame shape, stability region and emissions according to the swirl angle. The most significant feature of low swirl combustion is a occurrence of lifted flame. Such lifted flames happen to combine exquisitely propagating feature of premixed flame with diverging flow. This feature of lifted flame was confirmed through a velocity flow field and visualized the flame in this model combustor. The visualized flame was classified according to the thermal power and equivalence ratio. The variation study in swirl angles showed that the lean flammable limit could be extended only by swirl angles. Also, as the swirl angle increased, it was confirmed that the NOx and CO emissions were decreased due to the mixing enhancement and shorter resident time.

• Nuclear Engineering and Technology
• /
• v.51 no.5
• /
• pp.1373-1380
• /
• 2019

Besides promising implications as fertile nuclear materials, thorium carbonitrides are of great interest owing to their peculiar physical and chemical properties, such as high density, high melting point, good thermal conductivity. This paper reports first-principles simulation results on the structural, electronic and magnetic properties of cubic thorium carbonitrides $ThC_xN_{(1-x)}$ (X = 0.03125, 0.0625, 0.09375, 0.125, 0.15625) employing formalism of density-functional-theory. For the simulation of physical properties, we incorporated full-potential linearized augmented plane-wave (FPLAPW) method while the exchange-correlation potential terms in Kohn-Sham Equation (KSE) are treated within Generalized-Gradient-Approximation (GGA) in conjunction with Perdew-Bruke-Ernzerhof (PBE) correction. The structural parameters were calculated by fitting total energy into the Murnaghan's equation of state. The lattice constants, bulk moduli, total energy, electronic band structure and spin magnetic moments of the compounds show dependence on the C/N concentration ratio. The electronic and magnetic properties have revealed non-magnetic but metallic character of the compounds. The main contribution to density of states at the Fermi level stems from the comparable spectral intensity of Th (6d+5f) and (C+N) 2p states. In comparison with spin magnetic moments of ThSb and ThBi calculated earlier with LDA+U approach, we observed an enhancement in the spin magnetic moments after carbon-doping into ThN monopnictide.