• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.880-883
• /
• 2000

Temperature generated in the workpiece during grinding process can cause thermal damages. Therefore it is important to understand surface temperature generated during grinding process. In this paper, a theoretical and experimental investigation were performed for the grinding temperature. Grinding experiments were performed in machining center using vitrified bonded CBN cup-type wheel. The surface temperature was measured using thermocouple and calculated through a model of the partition of energy between wheel and workpiece. The residual stress and hardness of ground surface were measured. The experimental results indicate that the surface temperature was in good agreement with theoretical ones. Residual stress and hardness of ground surface were more affected by the change of table speed than the depth of cut.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.190-194
• /
• 2003

Two different types of nondestructive evaluation (NDE) techniques were employed to investigate the tensile behavior of ceramic matrix composites (CMCs). Two NDE methods, ultrasonic testing (UT) and infrared (IR) thermography, were used to assess defects and/or damage evolution before and during mechanical testing. Prior to tensile testing, a UTC-scan and a xenon flash method were performed to obtain initial defect information in light of UT C-scans and thermal diffusivity maps, respectively. An IR camera was used for in-situ monitoring of progressive damages. The IR camera measured temperature changes during tensile testing. This paper has presented the feasibility of using NDE techniques to interpret structural performance of CMCs.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.49-54
• /
• 2003

Most of the operating pressurized water reactors (PWRs)has chosen Inconel 600 as steam generator tubing. The long-term operation of steam generators showed that the use of this material induced localized corrosion damages. The current trend is using Inconel 690 as a tube material for the replacement steam generators. Based on the current trend, we have chosen Inconel 690 for the advanced Power Reactor 1400 (APR1400) steam generator tube material. In this paper, we examined the technical consideration in this modification: the effect of chemical composition, thermal conductivity, corrosion resistance and wear characteristics

• Vacuum Magazine
• /
• v.1 no.2
• /
• pp.19-23
• /
• 2014

Transparent and top emission organic light-emitting device (OLEDs) are the important issues in realizing new display applications such as see-through electronic displays, and flexible displays. The cathode of the transparent and top emission OLEDs should be transparent in the visible light and should not give any damage to the underlying organic layers, in addition to its intrinsic role of injecting electrons into the organic layers. Several authors have investigated the transparent conducting oxide films prepared by sputtering methods. They have introduced the sophisticated sputtering process for reducing the damages. Other groups have developed thermally evaporated transparent cathodes which are believed to be damage free without causing any permanent defect to the organic layers. This review focuses on the vacuum evaporated damage free transparent cathodes.

• International Journal of Precision Engineering and Manufacturing
• /
• v.8 no.3
• /
• pp.24-44
• /
• 2007

Cylindrical grinding is one of the important metal cutting processes used extensively in the finishing operation of discrete components. The inherent high cutting temperature in grinding if not controlled may lead to rapid tool wear, which in turn will lead to dimensional inaccuracy. The very nature of the grinding mechanism in material removal impairs the grounded surfaces by inducing residual stress, micro cracks and other thermal damages at the machined surface. This paper is an attempt to review some of the surface integrity issues in cylindrical grinding taken up and reported by number of researchers over the years. This review may have been planned to be useful to the researchers and other professionals interested to work on grinding.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.267-270
• /
• 2005

Recently, the damaged concrete structures are often strengthened or repaired using the polymer concrete or the polymer cement mortar. In the repaired concrete structures at early ages, internal stresses could be developed due to the differential drying shrinkage of the repair material. Due to the difference of the thermal coefficients of the repair material and existing concrete, additional stresses also could be developed as the structures are subjected to the ambient temperature changes. Theses environmentally-induced stresses can sometimes be large enough to cause damage to the structures, such as debonding of the interface between the two materials. In this study, a rational procedure was developed where anchors can be designed and installed to prevent damages in such structures by thermally-induced stresses. Finally, through the experimental and numerical study, the effects of the repair method using anchors with debonding was investigated and discussed the results.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.640-643
• /
• 2007

The effect of plasma damage was investigated on amorphous gallium-indium-zinc oxide (a-GIZO) films and transistors. Ion-bombardment by plasma process affects to turn semiconductor to conductor materials and plasma radiation may degrade to transistor electrical properties. All damages are easily recovered with a $350^{\circ}C$ thermal annealing.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.6
• /
• pp.181-186
• /
• 2007

UBM (Under Bump Metallurgy) of flip chip assemblies consists of several layers such as the solder wetting, the diffusion barrier, and the adhesion layers. In addition, IMC layers are formed between the solder wetting layers (e.g. Cu, Ni) and the solder. The primary failure mechanism of the solder joints in flip chips is widely known as the fatigue failure caused by thermal fatigues or electromigration damages. Sometimes, the premature brittle failure occurs in the IMC layers. However, these phenomena have thus far been viewed from only experimental investigations. In this sense, this paper presents a method for solid modeling of IMC layers in flip chip assemblies, thus providing a pre-processing tool for finite element analysis to simulate the IMC failure mechanism. The proposed modeling method is CSG-based and can also be applied to the modeling of UBM structure in flip chip assemblies. This is done by performing Boolean operations according to the actual sequences of fabrication processes

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.668-673
• /
• 2003

A wheel and axle failure can cause a derailment with its attendant loss of life and property. The service conditions of railway vehicles have become severe in recent years due to a general increase in operating speeds. Damages of railway wheel are a spalling by wheel/rail contact and thermal crack by braking heat etc. One of the main source of damage is a residual stress. therefore it is important to evaluate exactly. A Residual stress of wheel is formed at the process of heat treatment when manufacturing. it is changed by contact stress developed by wheel/rail contact. Distributions of residual stress vary according to a magnitude of wheel load, a magnitude of friction when acceleration and deceleration. The objective of this paper is to estimate the influence of wheel motion on the residual stress distribution in the vicinity of the running surface.

• Journal of the Korea Safety Management & Science
• /
• v.3 no.2
• /
• pp.25-31
• /
• 2001

Gas accidents are increasing every year, whereas the amount of using gas has been sharply increased due to conveniences, low-pollution, thermal efficiency of the gas. Gas accident has been recognizing serious social unstable elements as well as incredible economic damages of casualties of men and properties. For the prevention of the accidents, basic pre-countermeasure must be arranged to reduce gas accidents. The purpose of this study is to find out the strength of preliminary preventable functions against gas accidents throughout reformation of laws and regulations for insurance related in gas laws.