• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• 제12권1호
• /
• pp.41-48
• /
• 2016

To investigate the effect of long-term thermal aging on the microstructural and mechanical characteristics of weldment made of nickel base alloy and its weld metal, an accelerated heat treatment was applied to simulate the process of long-term thermal aging in the operating condition of nuclear power plant. A representative nickel-based weldment with Alloy 600 and Alloy 182 was fabricated and heat-treated at $400^{\circ}C$ for 1,713 h and 3,427 h to simulate the thermal aging for the period equivalent to 15 and 30 years in operating pressurized water reactors, respectively. The microstructural and mechanical characteristics were analyzed by using optical microscopy, scanning electron microscopy and Vickers microhardness measurement. Changes were observed in precipitation behavior and microhardness of each specimen, and these changes were mainly attributed to the change in precipitated morphology and residual stress across the weld during the thermal aging process.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제20권5호
• /
• pp.1717-1724
• /
• 1996

The present study investigates the effect of the shear rate-dependent thermal conductivity of non-Newtonian fluids on the heat transfer enhancement in a pipe flow. An axially-constant heat flux boundary condition was adopted in the thermal fully developed region. The present analytical results of Nusselt numbers for various non-Newtonian fluids show heat transfer enhancement over those of a shear rate-independent thermal conductivity fluids. The present analytical results showed good agreement with the previous experiments which excluded the temperature-dependent viscosity effect on heat transfer. This study also proposes the use of a shear rate-dependent thermal conductivity fluids in the design of a heat exchanger for heat transfer enhancement as well as reduction of fouling.

• Journal of Korea Foundry Society
• /
• 제32권6호
• /
• pp.276-283
• /
• 2012

This study presents the results on the changes of crucible thermal conductivity and inflow of Ar, and constructed the mathematical model about heat transfer into furnace. As process variables, simulation model was designated thermal conductivity of crucible to $0.5W{\cdot}m^{-1}{\cdot}K^{-1}$, $1W{\cdot}m^{-1}{\cdot}K^{-1}$, $2W{\cdot}m^{-1}{\cdot}K^{-1}$, $4W{\cdot}m^{-1}{\cdot}K^{-1}$, and inflow rate of Ar to 15 L/min, 30 L/min, 60 L/min. Initial condition and boundary condition were set respectively in two terms of process. Each initial conditions were set up by the preceding simulation of heat and fluid flow. The primary goal is the application of unidirectional growth of Si ingot using the result. In the result of the change of heat conductivity of crucible, the higher thermal conductivity of crucible shows the shorter solidification time and the bigger temperature difference. And the flow patterns are changed with the inflow rate of Ar. Finally, we found that the lower crucible's thermal conductivity, the better crucible is at polycrystalline Si ingot growth. But in case of Ar inflow, it is hard to say about good condition. This data will be evaluated as useful reference used in allied study or process variable control of production facilities.

• Journal of the Korean Society of Safety
• /
• 제14권2호
• /
• pp.122-126
• /
• 1999

In this study, using the temperature history analysis, the influences of the conductive values of wooden form, which are specified by Korean Standard for Concrete and ACI Practice Manual for Concrete, on the temperature history were examined. And, the calculated temperature history is compared with the measured temperature history. In the examination for the influences of the conductive values of wooden form, the value recommended by the Korean Standard can more closely predict the themperature history at the points which the variation of the boundary condition should be considered.

• Bulletin of the Korean Chemical Society
• /
• 제17권4호
• /
• pp.365-373
• /
• 1996

Time profile of the transient grating signal induced by a nanosecond pulsed laser excitation of methyl red is investigated in alcohols and toluene at several solvent temperatures. The signal decays biexponentially with well-separated time constants; the faster decay is identified as due to thermal diffusion of the solvents and the slower one as mainly due to translational diffusion of the solute. The measured translational diffusion constants of methyl red in toluene are close to a hydrodynamic prediction with a slip boundary condition while those in alcohols are larger by 30% and increase slightly with the size of alcohols. We compare the results with modified hydrodynamic models.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제6권3호
• /
• pp.1-10
• /
• 1998

In this paper, we investigated the improvement of characteristics of knock, emission and fuel consumption rate by optimizing the location and size of water transfer holes in cylinder head gasket without change of engine water jacket design itself. The cooling system was modified in the direction of reducing the metal temperature in the head and increasing the metal temperature in the block. The optimization of water transfer holes in cylinder head gasket was obtained by "flow visualization test". The water transfer holes were concentrated in front side of the engine in order to reduce thermal boundary layer in the water jacket of No. 2 and No. 3 combustion changer in the cylinder head, which would have a large knock intensity, and increase thermal boundary layer in the water jacket of the cylinder block. When the modified coolant flow pattern was applied as proposed in this paper, the knock characteristic was improved. The spark timing was advanced up to 2$^{\circ}$ in low and middle speed range at a full load. In addition, HC emission at MBT was reduced by 5.2%, and the fuel consumption rate was decreased up to 1% in the driving condition of 2400 rpm and 250 KPa. However, since this coolant flow pattern mentioned in this paper might deteriorate the performance of vehicle cooling system due to the coolant flow rate reduction, a properly optimized point should be obtained. obtained.

• The Korean Journal of Ecology
• /
• 제21권5_2호
• /
• pp.501-518
• /
• 1998

Mt. Paektu(2,749.6m)m the biggest mountain in Northeast Asia, located on the border line of Korea and China is characterized as an aspite with broad gentle mountain area and rich biota. however, it seems that the study of forest vegetational feature or vegetation zones in the whole area of this mountain is not yet sufficient in spite of contribution by many investigators. in this paper thermal climatic approach was carried out for the determination of vegetation zones of the mountain with the meteorological data of four stations including Cheonjj and various vegetational data. the application of Warmth Index and/or coldness Index(Kira 1977) for the determination of forest vegetation boundary was useful also here, and their boundaries largely coincided with those of thermal indicies obtained in the Korean Peninsula(Yim and Kira, 1975), including the lapse rate of air temperature along increasing elevation. However, in the mountain the boundary of vegetation zones in not clear like those of mountains in Korea. It may be due so the topographic differences between this area and the Korean Peninsula. Besides, the broad ecotones between different vegetations in this area support the vegetation continum concept rather than the unit concept, and the limit of timber line or tree line reflects various hypothesis(Steven and fox 1991). Therefore, for the explantion of vegetation zone of this area should be considered topography or soil condition, for example, as known the hierachy of ecological units (zonobiomes, orobiomes and pedobiomes, Walter, 1973).

• Coupled systems mechanics
• /
• 제1권2호
• /
• pp.205-217
• /
• 2012

A smart beam made of magneto-electro-elastic (MEE) material having piezoelectric phase and piezomagnetic phase, shows the coupling between magnetic, electric, thermal and mechanical under thermal environment. Product properties such as pyroelectric and pyromagnetic are generated in this MEE material under thermal environment. Recently studies have been published on the product properties (pyroelectric and pyromagnetic) for magneto-electro-thermo-elastic smart composite. Hence, the magneto-electro-elastic beam with different volume fractions, investigated under uniform temperature rise is the main aim of this paper, to study the influence of product properties on clamped-free boundary condition, using finite element procedures. The finite element beam is modeled using eight node 3D brick element with five nodal degrees of freedom viz. displacements in the x, y and z directions and electric and magnetic potentials. It is found that a significant increase in electric potential observed at volume fraction of $BaTiO_3$, $v_f$ = 0.2 due to pyroelectric effect. In-contrast, the displacements and stresses are not much affected.

• Proceedings of the KSME Conference
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.396-401
• /
• 2008

The disc-pad brake system is an important part of automobile safety system. During braking, the kinetic energy and potential energies of a moving vehicle are converted into the thermal energy through frictional heat between the brake disc and the pads. Most of the thermal energy dissipated through the brake disc. The temperature could be exceed the critical value for a given material, which leads to undesirable effects, such as the brake fade, premature wear, brake fluid vaporization, bearing failure, thermal cracks, and thermallyexcited vibration. The object of the present study is to investigate temperature field and temperature variation of brake disc and pad during single brake. The brake disc is decelerated at the initial speed with constant acceleration, until the disc comes to stop. The pad-disc brake assembly is built by 3D model with the appropriate boundary condition. In the simulation process, the mechanical loads are applied to the thermomechanical coupling analysis in order to simulate the process of heat produced by friction.

• Journal of the Korean Society of Mechanical Technology
• /
• 제20권6호
• /
• pp.745-750
• /
• 2018

In this study, the thermal behavior of adaptor housing was analyzed by the numerical method. The boundary conditions used to die casting process were the temperature of molten metal and injection time. As the temperature of the molten metal increased, the tensile strength of the product decreased by the blow hole generated in the molten metal, and the decreasing tendency was gradually decreased. As the injection time of the molten metal increased, the heat flux rose, but the degree of the increase was very small. So, the injection time of the molten metal had little effect on the thermal behavior and diffusion of the adapter housing. As a result, the heat of the molten metal was transferred into the housing and the thermal behavior spread widely.