• 한국공작기계학회논문집
• /
• 제11권3호
• /
• pp.102-109
• /
• 2002

The fatigue crack growth under mixed mode condition has been discussed within the scope of linear fracture mechanics such as maximum tangential stress, maximum tangential principal stress and minimum strain energy density. The purpose of this study is to investigate the characteristics of fatigue test crack growth in 304 stainless steel under mixed node. The fatigue test results carried out by using inclined pre-crack specimens was compared to both of the theoretical predictions of the criteria, maximum tangential stress and stain energy density. As difference from theoretical analysis, the transition region from mixed mode to mode I appeared in the fatigue test. There is deep relationship between the angle of slanted pre-crack and transition. Therefore, as applying the different stress intensity factor to each node I+II and mode I, the directions and rates of fatigue crack growth are evaluated more accurately under mixed mode.

• Journal of Power Electronics
• /
• 제12권3호
• /
• pp.487-494
• /
• 2012

A new low cost high power density photovoltaic power conditioning system (PV PCS) with an energy storage system is proposed in this paper. Its high power density and cost effectiveness can be achieved through the unification of the maximum power point tracker and the battery charger/discharger. Despite the reduced power stage, the proposed system can achieve the same performance in terms of maximum power point tracking and battery charging/discharging as the conventional system. When a utility power failure happens, the proposed system cannot perform maximum power point tracking at the UPS mode. However, the predetermined battery voltage near the maximum power point of the PV array can effectively generate a reasonable PV power even at the UPS mode. Therefore, it features a simpler structure, less mass, lower cost, and fewer devices. Finally, to confirm the operation, validity, and features of the proposed system, a theoretical analysis and experimental results from a single phase AC 220Vrms/1.5kW prototype are presented.

• 한국세라믹학회지
• /
• 제19권2호
• /
• pp.115-120
• /
• 1982

본 논문은 알루미나의 초기 성형밀도가 소결후 소결밀도에 미치는 영향에 대한 것이다. 실험에서는 두가지의 Reactive alumina powder (ALCOA A-16, A-17)를 사용하였으며, 넓은 범위의 성형밀도를 얻기 위하여 낮은 성형압을 가할 수 있는 기계적으로 작동하는 press와, 높은 성형압을 가할 수 있는 유압식 press를 사용하여, 이론밀도의 35%에서 65% 범위의 시편들 (A-16 alumina powder)과 46%에서 66% 범위의 시편들 (A-17 alumina powder)을 준비하였다. 성형밀도를 Log (성형압)에 대해 plot해 A-16과 A-17 alumina powder들에 대한 Compaction mechanism이 추론되었다. 1350, 1450, 155$0^{\circ}C$에서 소결하여 밀도증가량 ($D_T$-$D_P$)을 상대 성형밀도($D_P$/$D_T$) 에 대해 plot해 Ford가 제안한 두 변수 사이의 포물선 관계가 잘 성립 함을 보였다.

• Structural Engineering and Mechanics
• /
• 제71권3호
• /
• pp.271-282
• /
• 2019

The span record of cable-stayed bridges has exceeded 1,000 m, which makes research on the maximum possible span length of cable-stayed bridges an important topic in the engineering community. In this paper, span limit is discussed from two perspectives: the theoretical span limit determined by the strength-to-density ratio of the cable and girder, and the engineering span limit, which depends not only on the strength-to-density ratio of materials but also on the actual loading conditions. Closed form equations of both theoretical and engineering span limits of cable-stayed bridges determined by the cable and girder are derived and a detailed parametric analysis is conducted to assess the engineering span limit under current technical conditions. The results show that the engineering span limit of cable-stayed bridges is about 2,200 m based on materials used available today. The girder is the critical member restricting further increase in the span length; its compressive stress is the limiting factor. Approaches to increasing the engineering span limit are also presented based on the analysis results.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제15권12호
• /
• pp.4492-4507
• /
• 2021

In camera sensor networks (CSNs), in order to better identify the point, full-view problem requires capture any facing direction of target (point or intruder), and its coverage prediction and sensor density issues are more complicated. At present, a lot of research supposes that a large number of homogeneous camera sensors are randomly distributed in a bounded square monitoring region to obtain full-view rate which is close to 1. In this paper, we deduce the sensor density prediction model in heterogeneous deployed CSNs with arbitrary full-view rate. Aiming to reduce the influence of boundary effect, we introduce the concepts of expanded monitoring region and maximum detection area. Besides, in order to verify the performance of the proposed sensor density model, we carried out different scenarios in simulation experiments to verify the theoretical results. The simulation results indicate that the proposed model can effectively predict the sensor density with arbitrary full-view rate.

• Journal of Mechanical Science and Technology
• /
• 제16권12호
• /
• pp.1594-1603
• /
• 2002

In this paper, when the initial propagation angle of a branched crack is calculated from the maximum tangential stress criterion (MTSC) and the minimum strain energy density criterion (MSEDC), it is essential that you use stress components in which higher order terms are considered and stress components at the position in a distance 0.005㎜ from the crack tip (=r). When an interfacial crack propagates along the interface at a constant velocity, the initial propagation angles of the branched crack are similar. to the mode mixities (phase angle) and the theoretical values obtained from MTSC and MSEDC. The initial propagation angle of the branched crack depends considerably on the stress intensity factor K$_2$.

• 대한기계학회논문집B
• /
• 제30권10호
• /
• pp.982-986
• /
• 2006

It is well known that the surface tension forces can make a particle denser than water float when the size of the particle is of the order of 1 mm. This is deeply related to the basic mechanism enabling small insects to wander around on the pond surface and also to a newly emerging technology of self-assembly using capillary forces. For the quantitative understanding of this effect, we experimentally study the maximum density of a cylinder that can float on water and how fast the cylinder sinks when the density exceeds the maximum value. We compare our experimental results with the theoretical prediction and find good agreement between them.

• 한국세라믹학회지
• /
• 제20권3호
• /
• pp.211-216
• /
• 1983

This work aims at characterizing silicon grains and its compacts. In order to remove iron silicon grains were washed with 5N hydrochloride at 60-7$0^{\circ}C$ for 170 hrs, and then followed the chemical analysis by atomic absorption spectrophotometer X-ray diffraction analysis SEM observation and specific surface area determination by B. E. T. Mixtures of graded silicon particles with two or three different sizes were made into packings by mechanical vibration. The mixtures were used to make compacts with 10 mm in diameter and 70mm in length by isostatically pressing at 1, 208 kg/$cm^2$ (20 kpsi) and 4, 255kg/$cm^2$ (60 kpsi) respectively. Bulk densities of packings and compacts were measured. A slip made of magnesium nitrate solution and fine silicon particles was spray-dried and then decomposed at 30$0^{\circ}C$ for the purpose of coating the uniform layer of magnesium oxide on the surface of particles. The results obtained are as follows: (1) About two thirds of iron content could be removed from silicon by washing silicon powders with hydrochloride. (2) Uniform layer of magnesium oxide on the surface of silicon could be prepared by spray-drying suspension and by decomposing it. (3) B. E. T. specific surface area of fine silicon particles was 2, 826.753$m^3$/kg. (4) In the binary system with two sizes of 40-53$\mu\textrm{m}$ particles and <10$\mu\textrm{m}$ particles the maximum bulk density of packing was 55% of theoretical value and that of compacts made at the pressure of 4, 255 kg./$cm^2$ (60 kpsi) was 73% of theoretical value. (5) In the ternary system with three sizes the maximum bulk density of packing was 1.43 g/$cm^3$and that of compacts was 1.80g/$cm^3$which is equivalent to 77.6% of theoretical value. The composition of the closest compact was consisted of 50% of 40-53$\mu\textrm{m}$ particles 20% of 10-30$\mu\textrm{m}$ particles and 30% of <10$\mu\textrm{m}$ parti-cles.

• 한국염색가공학회지
• /
• 제27권2호
• /
• pp.132-141
• /
• 2015

Fall-arrest systems(maximum arrest force and allowable free-fall) have been widely applied to provide a safe stop during fall incidents for various industrial activities. Fabric structure affects on the mechanical properties of shock energy absorber. The object of this study is to perform the basic research for the evaluation of the capacity of fall arrest energy absorber in relation to the different interlace yarn density. In this work, pack style energy absorber was prepared by weaving 10 types(Interlace yarn density used high tenacity PET 1000D : 60, 59, 58, 57, 56, 55, 54, 53, 52, 51). The paper presents the results of theoretical investigations of the performance of adjustable absorber during fall arrest. Dynamic load tests based on the EU fall protection equipment standard(CE : EN355:2002) were conducted. Results showed that the maximum arrest force by dynamic load test of energy absorber was satisfied with global standard(below 6,000N). Also, Maximum allowable free-fall of energy absorber showed below 1.75m.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.267-270
• /
• 1998

We measured the dielectric properties with YMnO$_3$ ceramics using solution method based procedure via by citrate. The crystalline phases were determined using XRD. Also we observed morphologies of YMnO$_3$ ceramics using SEM. We proved the structure of YMnO$_3$ ceramics which is hexagonal. But lots of pores were observed the microstructure. It would be considered as volatile organic. The maximum density of YMnO$_3$ ceramics is obtained sintering temperature 135$0^{\circ}C$ and the ratio 0.95/1.05 of Y/Mn. But even though the density we obtained is the highest, that is lower than theoretical density because of remaining organics by citric acid. Dielectric constant and dissipation factor were improved as increasing sintering temperature and the Y/Mn ratio (0.95/1.05)